Instructions / Assembly
BEAM
TOW BAR
SUPPORT LEG
Retighten the axle nut until "nger tight."
Insert the cotter pin through the hole in the axle. Bend open
and spread the prongs in opposite directions so the axle nut
will not come off (make sure the tire spins freely).
Use a soft-faced hammer to tap the anti-dust washer in the
right position.
Align the wheel cap against the wheel hub. Use a soft-faced
hammer to tap the wheel cap onto the wheel hub properly.
Follow the same procedure to assemble the other wheel
(follow steps 4 – 12 under wheel assembly.)
Insert the tow bar into the tank pivot mount. Align the holes in
the tow bar with the holes in the tank pivot mount. Connect and
tighten the tow bar to the tank by using the M12x90 bolts, flat
washers, spring washer, and nuts. (See
Figure 4
)
Lift the tow bar slightly. Pull out the lock lever and put the
support leg in the DOWN position, then release the lever and
make sure the leg is secured. Remove the bottom pallet.
Hold and pull the beam until the log cradle mount and the
beam is against the wooden block in-pallet.
Slowly lift the top of the beam and stand the beam on the end
plate in the vertical position.
11.
10.
13.
1.
2.
9.
12.
Support Leg
Support Leg Lock
Lifting Handle
PIVOT BRACKET
BEAM TO RESERVOIR
BEAM LOCK BRACKET
Align the holes in the pivot bracket with the holes on the beam
and insert and tighten bolts, spring washers, and at washers.
M10x25 (x4)
Pivot Bracket
Beam
Parallel Lines
Make sure a helper holds on to the beam to keep it from
falling. Reposition the beam and reservoir so the back of the
tank is facing the vertical beam as shown in
Figure 7a
.
When mounting the lock latch assembly, make sure the latch
rod side of the bracket is on the same side as the engine.
Install the beam lock bracket to the beam by using the beam
lock M10x25 bolts, spring washer, and flat washers. (See
Figure 8a
)
Align the pivot bracket on the beam assembly to the pivot
mount on the tank weldment and insert the beam pivot pin
and washer. (See
Figure 7b
)
Insert the bridge pin through the hole in the beam pivot pin.
1.
1.
2.
3.
The beam can be very heavy and dangerous if
that it tips over and may cause personal injury.
Beam Pivot Pin (x1)
Tank Pivot Mount
Washer (x1)
Bridge Pin (x1)
Pivot Bracket
M10x25 (x2)
Beam Lock Bracket
Beam
Parallel Lines
After the beam and cylinder assembly is in the
vertical position, a helper is needed to prevent
the beam from tipping over until it is secured on
the hydraulic tank assembly with the hitch pin
and R-clip.
The beam assembly is heavy and has a small foot
print. When in the vertical position, the beam may
fall, causing damage to the machine and could
result in personal injury.
M12 X 90 X 2
2
M10 X 25 X 4
3
20 X 110 X 1
4
Bridge Pin
X 1
M10 X 25 X 2
5
M12x90 (x2)
Tank Assembly
Tow Bar
Tank Pivot Mount
M12 (x2)
16
mm
13
mm
18
mm
19
mm
30
mm
32
mm
X 2
32
mm
13
mm
16
mm
19
mm
32
mm
13
mm
16
mm
19
mm
Figure 3a
Figure 4
Figure 6
Figure 7b
Figure 8a
Figure 7a
Figure 5Figure 3b
Beam
Installation of the cotter pin is important and
required. Failure to install the cotter pin can result in
loss of wheel retention. Always assemble using a new
cotter pin. Do not reuse.
Wooden Block
Log Cradle Mount
Beam
13 14
Gas Log Splitter
»
Operator’s Manual
|
Assembly Assembly
|