Instructions / Assembly

ManualsBrandsYARDMAX ManualsGas Leaf BlowersWalk-Behind Gas Blower

■■■■■

Y�

■

■■■■



Walk-Behind Blower

Assembly Manual

MODEL NUMBER

YF1565

SERIAL NUMBER

PURCHASE DATE





Page 2, Fure 











READ AND UNDERSTAND THE ENTIRE MANUAL BEFORE OPERATING MACHINE.

FAILURE TO COMPLY WITH THE SAFETY INSTRUCTIONS IN THE MANUAL

MAY RESULT IN PERSONAL INJURY.

Tame the Great Outdoors·

Summary of content (9 pages)

PAGE 1
7 ■■■■■ ■ ■■■■ Save This Manual for Future Reference YARDMAX� Walk-Behind Blower Assembly Manual MODEL NUMBER YF1565 SERIAL NUMBER PURCHASE DATE Both model number and serial number may be found on the main label. (See Page 2, Figure 1 of your User Manual) You should record both of them in a safe place for future use. READ AND UNDERSTAND THE ENTIRE MANUAL BEFORE OPERATING MACHINE. FAILURE TO COMPLY WITH THE SAFETY INSTRUCTIONS IN THE MANUAL MAY RESULT IN PERSONAL INJURY.
PAGE 2
7 ■■■■■ Walk-Behind Blower » Operator's Manual sealed by the manufacturer or distributor. Only a qualified service technician may adjust parts that increase or decrease governed of any moving parts. Parts that are broken or worn down that may affect the machine's operation. If damage or worn parts are engine speed. identified, they should be repaired before use. Many accidents are caused by poorly maintained equipment.
PAGE 3
7 ■■■■■ ■■■■ ■ ASSEIMBLY This walk-behind blower was partially assembled at the factory. To assemble your machine follow the below instructions. FRAME Insert the end of the front swivel caster tube into the opening of the frame tube, and align the holes. Attach the tubes to the engine deck with M8x40 bolt, arc washer, spring washer and lock nut in four places. Tighten securely using two 13mm wrenches.
PAGE 4
7 ■■■■■ Walk-Behind Blower UPPER HANDLE � NOTE » Operator's Manual THROTTLE CONTROL LEVER There are two positions in which the handle can be attached - a high position and a lower position. Hook the upper handle tabs into the holes on the frame tube (See Figure 5, illustration1). Use the bottom hole for the lower handle position. Use the middle hole for the high handle position. Mount the throttle control lever onto the right upper handle with M5x25 screw and lock nut.
PAGE 5
7 ■■■■■ FLOW ANGLE ADJUSTMENT CONTROL CABLE ■ FRONT DISCHARGE CHUTE Attach the Z type end of the cable into the lever as shown. (See Figure 7, illustration 1) Secure the buckle on the cable onto the upper handle. (See Figure ■■■■ � NOTE The front discharge chute is used to redirect the air flow to the front of the blower. Attach it when needed. 7, illustration 2) Secure the cable on the frame tube with cable clamp.
PAGE 6
7 ■■■■■ Walk-Behind Blower » Operator's Manual KNOW YOUR MACHINE FEATURES ANID CONTROLS l•Hffi05«@®■3M§ •--------------� lift\Hi¥%i: Intake Guard Upper Handle Frame Tube Front Discharge Chute lii·lllftbtildi§ Discharge Chute Know Your Machine I 12
PAGE 8
7 ■■■■■ Walk-Behind Blower » Operator's Manual Throttle Control Lever )) Regulates the speed of engine. Moving towards FAST9 to speed up the engine. Moving towards LOW-A to lower the engine speed. Flow Angle Adjustment Control Lever )) Adjusts the direction of air flow between 7 positions. Fan Housing )) Contains the fan. Flow Angle Adjustment Index Lever )) Recoil Starter Handle )) )) Front Swivel Caster )) 360 degree swiveling caster to allow for maneuverability.
PAGE 9
■■■■■ ■ ■■■■ yardmax.com Tame the Great Outdoors* 847-327-0566 or 844-YARDMAX I info@yardmax.