Product Manual

Section 4: Know Your Chipper Shredder:
Stopping the engine: The only way to
VWRSWKH HQJLQHLV WKURXJK D6723 EXWWRQ
SODFHG LQ WKH HQJLQH E\ WKH HQJLQH¶V
PDQXIDFWXUHU $OVR GLVFRQQHFW WKH VSDUN
plug wire if you will not use the machine for
DVLJQLILFDQWDPRXQWRIWLPH
Engine Controls: 6HH WKH VHSDUDWH
engine manual for the location and function
RIWKHFRQWUROVRQWKHHQJLQH
Starter Handle: The starter handle is
ORFDWHG RQ WKH HQJLQH 3XOO WKH VWDUWHU
hanGOHWRVWDUWWKHHQJLQH
Engine Adjustable Mount Base: We
have designed the machine with an
adjustable mount base to allow the use of
GLIIHUHQW EHOWV LQ FDVH \RX FDQ¶W KDYH WKH
RQH VSHFLILHG E\ WKH PDQXIDFWXUHU $OVR
PDNHV LW PRUH FRPIRUWDEOH WR DGMXVW WKe
tension on the belt since the force will be
exerted by a wrench on a nut instead of
\RXRQWKHHQJLQH
Deflector:<RXFDQDGMXVWGHIOHFWLQJDQJOH
of the product by placing its location pin on
RQH RI WKH WKUHH KROHV JLYHQ IRU LW 7KHVH
three holes are inDKRUL]RQWDOSDWWHUQVHH
ILJXUH,I\RXQHHGWRUHSDLULQVLGHFKDQJH
a sieve, or just clean up, then you can use
a fourth hole placed on the upper part of
WKH PDFKLQH IRU VXSSRUWLQJ WKH GHIOHFWRU
5HPHPEHU LI \RX DUH HYHU WR EH ZRUNLQJ
on the inner parts of the machine, then you
must allow the machine come to a
FRPSOHWH VWRS GLVFRQQHFW WKH VSDUN SOXJ
ZLUHDQGJURXQGLWDJDLQVWWKHHQJLQH
Side Hopper: This hopper is for chipping
EUDQFKHV RQO\ <RX FDQ FKLS IURP ò´ LQ
GLDPHWHU XS WR ´ LQ GLDPHWHU :Ken
chipping big diameter branches, it is
UHFRPPHQGHG\RXFKLSLQDEUHDNSDWWHUQ
that is -\RXFKLS\RXJREDFN\RXFKLS\RX
JR EDFN - 7U\LQJ WR FRQWLQXRXVO\ FKLS ELJ
branches may stall the machine and will
cause discomfort in your hands even when
using OHDWKHU JORYHV 5HPHPEHU WR XVH
only leather gloves when chipping
EUDQFKHVWKURXJKWKHVLGHKRSSHU
Main Hopper: This hopper is for inserting
OHDYHVRIDQ\NLQGGU\ZHWDQGVPDOOGU\
EUDQFKHV XS WR ò´ LQ GLDPHWHU ,W LV
preferably that all wood and leaves are of a
GU\NLQG7KLVJXDUDQWHHVORQJHUOLIHRIWKH
PDFKLQHEHFDXVHRIUXVWIRUH[DPSOH
<RXU<$5'%($67&KLSSHU6KUHGGHUKDYH
clearly two different ways of operation, or
better said, two different applications, that
is shred leaves and chip branchHV 7KHUH
are two ways of feeding the machine,
through the main hopper and through the
VLGH KRSSHU <RX QHHG WR NQRZ D IHZ
components and controls before operating
WKLVPDFKLQH

6WRS(QJLQH%XWWRQ

(QJLQH$GMXVWPHQW%DVH
3
Main Hopper

6WDUWHU+DQGle
5
'HIOHFWRU$QJOH$GM
6
6LGH+RSSHU
7
6LHYH+ROGLQJ5RG

'LVFKDUJH&KXWH
Sharpening or replacing chipping blades:
For sharpening or replacing blades you will need to
take off both front-cover and side hopper.
Read more below. This 11-step operation can take from
15min to 1 hour (for unexperienced users).
BEFORE STARTING TO SERVICE YOUR EQUIPMENT,
YOU MUST DISCONNECT THE ENGINE’S SPARK
PLUG. FAILURE TO DO SO MAY RESULT IN INJURY
OR DEATH TO YOU OR OTHERS.
1
2
You will need to use (2) two 9/16” hex wrench. First loosen top bolts
that are fastening the front cover against the Top Hopper and cutting
chamber. Repeat for bolts below.
Repeat as indicated on step 1.