Operator’s Manual Two-Stage Snow Thrower Style L IMPORTANT: READ SAFETY RULES AND INSTRUCTIONS CAREFULLY Warning: This unit is equipped with an internal combustion engine and should not be used on or near any unimproved forest-covered, brushcovered or grass-covered land unless the engine’s exhaust system is equipped with a spark arrester meeting applicable local or state laws (if any). If a spark arrester is used, it should be maintained in effective working order by the operator.
TABLE OF CONTENTS Content Important Safe Operation Practices Assembling Your Snow Thrower Know Your Snow Thrower Operating Your Snow Thrower Making Adjustments Page 3 6 8 10 13 Content Maintaining Your Snow Thrower Servicing Your Snow Thrower Troubleshooting Illustrated Parts List Warranty Page 15 15 20 22 Back Cover FINDING MODEL NUMBER This Operator’s Manual is an important part of your new snow thrower. It will help you assemble, prepare and maintain the unit for best performance.
SECTION 1: IMPORTANT SAFE OPERATION PRACTICES WARNING: Engine Exhaust, some of its constituents, and certain vehicle components contain or emit chemicals known to the State of California to cause cancer, birth defects or other reproductive harm. DANGER: This machine was built to be operated according to the rules for safe operation in this manual. As with any type of power equipment, carelessness or error on the part of the operator can result in serious injury.
Operation 18. Never put your hand in the discharge or collector openings. Always use the clean-out tool provided to unclog the discharge opening. Do not unclog chute assembly while engine is running. Shut off engine and remain behind handles until all moving parts have stopped before unclogging. 19. Use only attachments and accessories approved by the manufacturer (e.g. wheel weights, tire chains, cabs etc.). 20. If situations occur which are not covered in this manual, use care and good judgment.
YOUR RESPONSIBILITY Restrict the use of this power machine to persons who read, understand and follow the warnings and instructions in this manual and on the machine. Do not modify engine Notice regarding Emissions To avoid serious injury or death, do not modify engine in any way. Tampering with the governor setting can lead to a runaway engine and cause it to operate at unsafe speeds. Never tamper with factory setting of engine governor.
SECTION 2: ASSEMBLING YOUR SNOW THROWER 1 2 3 NOTE: References to right or left side of the snow thrower are determined from behind the unit in the operating position (standing directly behind the snow thrower, facing the handle panel). IMPORTANT: Two replacement auger shear pins are included with this manual (or stowed in the plastic handle panel). Refer to Augers on page 19 for more information regarding shear pin replacement.
NOTE: If the flange keepers will not easily click into place, use the palm of your hand to apply swift, firm pressure to the back of each. 5 5. Remove the clevis pin and hairpin clip from the upper portion of the chute mast. • Position the control head over the chute mast and rear portion of the chute assembly. • Re-insert the clevis pin and secure with the hairpin clip removed earlier. CAUTION: Prior to operating your snow thrower, refer to Auger Control Test on page 11.
SECTION 3: KNOW YOUR SNOW THROWER Drive Control Shift Lever Chute Directional Control Auger Control Electric Starter Button Engine Controls Gas Cap Recoil Starter Handle Oil Fill Electric Starter Outlet Chute Assembly Primer Clean-out Tool Ignition Key Choke Control Throttle Control Skid Shoe Augers Choke Control WARNING: Read, understand, and follow all instructions and warnings on the machine and in this manual before operating.
Auger Control Ignition Key The ignition key is a safety devise. It must be fully inserted in order for the engine to start. Remove the ignition key when the snow thrower is not in use. AUGER CONTROL IMPORTANT: Do not turn the ignition key in an attempt to start the engine. Doing so may cause it to break. Clean-Out Tool WARNING: Never use your hands to clear GO a clogged chute assembly. Shut off engine and remain behind handles until all moving parts have stopped before unclogging.
SECTION 4: OPERATING YOUR SNOW THROWER Before Starting WARNING: If your home electrical system is grounded, but a three-hole receptacle is not available, do not use your snow thrower’s electric starter. WARNING: Read, understand, and follow all instructions and warnings on the machine and in this manual before operating.
• To Engage Drive Pull the starter handle with a firm, rapid stroke. IMPORTANT: Do not release the handle and allow it to • snap back. Keep a firm hold on the starter handle and allow it to slowly recoil. • As the engine warms, slowly rotate the choke control to the OFF position. If the engine falters, quickly rotate the choke control back to the FULL position and then slowly into the OFF position again.
• • • • To readjust the control cable, loosen the hex jam nut on the auger control cable “Z” fitting. Rotate the coupling end of the cable counterclockwise to provide more slack. Retighten the hex jam nut. See Figure 1. Repeat Auger Control Test to verify proper adjustment has been achieved. • • Remove the clean-out tool from the clip which secures it to the rear of the auger housing.
SECTION 5: MAKING ADJUSTMENTS WARNING: Never attempt to make any adjustments while the engine is running, except where specified in operator’s manual. 1 Shift Rod Adjustment If the full range of speeds (forward and reverse) cannot be achieved, refer to the figures to the right and adjust the shift rod as follows: 1. Place the shift lever in the fastest forward speed position and remove the hairpin clip which secures the ferrule to the shift lever. 2. Rotate the shift arm clockwise as far as it will go. 3.
Drive Control When the drive control is released and in the disengaged “up” position, the cable should have very little slack. It should NOT be tight. Check the adjustment of the drive control as follows: 1. With the drive control released, push the snow thrower gently forward. The unit should roll freely. 2. Engage the drive control and gently attempt to push the snow thrower forward. The wheels should not turn. The unit should not roll freely. 3.
SECTION 6: MAINTAINING AND SERVICING YOUR SNOW THROWER WARNING: Before lubricating, repairing, or Auger Shaft inspecting, disengage all controls and stop engine. Wait until all moving parts have come to a complete stop. • At least once a season, remove the shear pins on auger shaft. Spray lubricant inside shaft, around the spacers. Also lubricate the flange bearings found at either end of the shaft. See Figure 6.
Auger Belt Replacement 1 To remove and replace your snow thrower’s auger belt, proceed as follows: 1. Remove the plastic belt cover on the front of the engine by removing the two self-tapping screws. • Drain the gasoline from the snow thrower, or place a piece of plastic under the gas cap. • Carefully pivot the snow thrower up and forward so that it rests on the auger housing. 2. Remove the frame cover from the underside of the snow thrower by removing four self-tapping screws which secure it. 3.
Drive Belt Replacement 1 To remove and replace your snow thrower’s auger belt, proceed as follows: 1. Remove the plastic belt cover on the front of the engine by removing the two self-tapping screws. • Drain the gasoline from the snow thrower, or place a piece of plastic under the gas cap. • Carefully pivot the snow thrower up and forward so that it rests on the auger housing. 2. Remove the frame cover from the underside of the snow thrower by removing four self-tapping screws which secure it. 3. a.
Friction Wheel Removal 1 If the snow thrower fails to drive with the drive control engaged, and performing the drive control cable adjustment on page 14 fails to correct the problem, the friction wheel may need to be replaced. Follow the instructions below. Examine the friction wheel for signs of wear or cracking and replace if necessary • • Place the shift lever in third Forward (F3) position. Drain the gasoline from the snow thrower, or place a piece of plastic under the gas cap.
Augers • • IMPORTANT: NEVER replace the auger shear pins with anything other than OEM Part No.738-04124 replacement shear pins. Any damage to the auger gearbox or other components as a result of failing to do so will NOT be covered by your snow thrower’s warranty. The augers are secured to the spiral shaft with two shear pins and cotter pins. If the auger should strike a foreign object or ice jam, the snow thrower is designed so that the pins may shear. Refer to Figure 6.
SECTION 8: TROUBLE SHOOTING GUIDE Trouble Possible Cause(s) Engine fails to start Fuel tank empty, or stale fuel. Corrective Action Fill tank with clean, fresh gasoline. Fuel will not last over thirty days unless a fuel stabilizer is used. Blocked fuel line. Clean fuel line. Choke control not in ON position Move choke control to ON position Faulty spark plug. Clean, adjust gap or replace. Ignition key not present. Insert key into ignition switch. Spark plug wire disconnected. Connect spark plug wire.
NOTES 21
SECTION 9: PARTS LIST 5 30 25 21 10 15 26 9 7 22 13 28 3 8 16 48 19 18 40 35 1 4 17 47 15 34 12 23 33 27 2 29 11 49 31 24 6 14 32 41 52 20 46 37 50 38 55 53 51 36 44 43 42 45 39 54 22
Style L REF. PART NO. NO. 1 631-04124 631-04128 2 631-04133 3 631-04134 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 684-04105 684-04106 710-04326 710-04354 710-1026 710-1233 711-04287 711-0677 712-04064 712-04081A 714-0104 720-0274 720-04039 725-04213 725-04214 725-1649 726-0470 731-04894 731-04896 732-0193 732-04219 732-04238 735-0199A NOTE: DESCRIPTION Panel Assembly, L-Style, Yellow (Inc. Ref. 47) Panel Assembly, L-Style, Black (Inc. Ref.
Style L 37 27 7 40 38 36 28 31 29 26 48 39 33 7 1 17 9 23 13 69 41 3 15 5 43 9 25 32 19 34 7 18 30 12 22 14 24 6 9 4 2 8 4 6 35b 51 35a 7 7 45 64 53 55 60 56 57 67 49 59 68 62 42 54 65 63 66 58 61 20 46* 50 47 44 10 21 24 52
Style L REF. NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 PART NO.
Style L 58 55 41 50 17 7 9 66 58 53 46 57 47 40 54 44 59 49 7 52 45 51 43 48 56 7 13 9 39 20 24 30 21 6 24 29 16 18 27 12 1 14 15 34 2 36 28 35 24 14 9 4 3 10 22 33 26 32 19 11 23 5 42 8 20 9 31 9 37 28 38 25 4 9 63 62 61 65 64 60 26 7
Style L REF. NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 PART NO.
MANUFACTURER’S LIMITED WARRANTY FOR: The limited warranty set forth below is given by MTD LLC with respect to new merchandise purchased and used in the United States, its possessions and territories. “MTD”warrants this product against defects in material and workmanship for a period of two (2) years commencing on the date of original purchase and will, at its option, repair or replace, free of charge, any part found to be defective in materials or workmanship.
