Operator's Manual 3,200 PSI MAX* @ 2.5 GPM 2,400 PSI @ 2.7 GPM MAX* GAS PRESSURE WASHER Model No. Y0GWC3200R0 PRESSURE WASHER CUSTOMER HELPLINE 1-866-902-9690 HOURS: Mon. - Fri. 8 a.m. to 5 p.m. (ET) WARNING Before using this product, read this manual and follow all Safety Rules and Operating Instructions.
TABLE OF CONTENTS SAFETY RULES..............................................................3-5 STORAGE........................................................................ 21 FEATURES AND CONTROLS............................................6 TROUBLESHOOTING......................................................22 ASSEMBLY...................................................................7 -10 NOTES..............................................................................23 OPERATION............
SAFETY RULES Read this manual carefully and become familiar with your pressure washer. Know its applications, its limitations, and any hazards involved. WARNING POISONOUS GAS HAZARD. Engine exhaust contains carbon monoxide, a poisonous gas that could kill you in minutes. You CANNOT smell it, see it, or taste it. Even if you do not smell exhaust fumes, you could still be exposed to carbon monoxide gas.
WARNING Starter cord kickback (rapid retraction) will pull hand and arm toward engine faster than you can let go which could cause broken bones, fractures, bruises, or sprains resulting in serious injury. WARNING Fuel and its vapors are extremely flammable and explosive which could . cause burns, fire or explosion resulting in death or serious injury. WHEN ADDING OR DRAINING FUEL • NEVER pull starter cord without first relieving spray gun pressure.
WARNING Exhaust heat/gases could ignite combustibles, structures or damage fuel tank causing a fire, resulting in death or serious injury. WARNING Starter and other rotating parts could entangle hands, hair, clothing, or accessories resulting in serious injury. • NEVER operate pressure washer without protective housing or covers. Contact with muffler area could cause burns resulting in serious injury.
FEATURES AND CONTROLS KNOW YOUR PRESSURE WASHER Read the operator's manual and safety rules before operating your pressure washer. Compare the illustrations with your pressure washer to familiarize yourself with the locations of various controls and adjustments. Save this manual for future reference. C B A D E O F N G M L H K J I K- Engine switch - Set the engine in starting mode and stop a running engine. L- Oil Fill Cap/ Dipstick - Check, fill and drain engine oil here.
ASSEMBLY Your pressure washer requires some assembly and is ready for use only after it has been properly serviced with the recommended oil and fuel. Become familiar with each piece before assembling the pressure washer. Check all contents against the illustration. If any parts are missing or damaged, call the pressure washer helpline at 1-866-902-9690. If you have any problems with the assembly of your pressure washer, please call the pressure washer help line at 1-866-902-9690.
To protect the fuel system from gum formation, mix in a fuel stabilizer when adding fuel. See “Storage”. All fuel is not the same. If you experience starting or performance problems after using fuel, switch to a different fuel provider or change brands, This engine is certified to operate on gasoline. The emission control system for the engine is EM (Engine Modifications). 3.
NOTICE: ALWAYS apply a small amount of lubricant on o-rings prior to assembling the garden hose to the pump (C), high pressure hose (D), spray gun (E), and spray wand (F). WARNING! The high pressure stream of water that the pressure washer produces could cut through skin and its underlying tissues, resulting in serious injury and possible amputation. • NEVER connect high pressure hose to spray wand. E • Keep high pressure hose connected to pump and spray gun while system is pressurized.
CHECK LIST BEFORE STARTING ENGINE 5) Turn ON the water, point the spray gun at a safe direction, release the red trigger lock, then squeeze trigger to purge the pump system of air and impurities. Review the assembly to ensure you have performed all of the following: • Be sure to read "Safety Rules" and "Operation" sections before using the pressure washer. • Make sure handle is in place and secure. • Check that oil has been added to proper level in engine crankcase. • Add proper gasoline to fuel tank.
OPERATION HOW TO USE YOUR PRESSURE WASHER Risk of Fire Clearances WARNING Exhaust heat/gases could ignite combustibles, structures or damage fuel tank causing a fire, resulting in death or serious injury. If you have any problems operating your pressure washer, please call the pressure washer helpline at 1-866-902-9690. • Keep at least 5 ft. (1.5 m) clearance on all sides of pressure washer including overhead.
NOTICE: Before starting the pressure washer, be sure you are wearing safety goggles as described below. WARNING! Risk of eye injury. Spray could splash back or propel objects resulting in serious injury. Hold By One Hand • Always wear indirect vented (chemical splash) safety goggles marked to comply with ANSI Z87.1 when using or in vicinity of this equipment. Pull Recoil Starter By The Other Hand • NEVER substitute safety glasses or dry-condition goggles for indirect vented safety goggles. 10.
• Every time when you stop engine, ALWAYS point spray gun at safety direction, release the red trigger lock, and squeeze spray gun trigger to release high pressure. gun while system is pressurized. • NEVER aim spray gun at people, animals, or plants. • DO NOT secure spray gun in open position. • DO NOT leave spray gun unattended while machine is running. NOTE: A small amount of water will squirt out when you release the pressure.
Usage Tips washing and rinsing. Reapply as needed to prevent surface from drying. DO NOT allow detergent to dry on (prevents streaking). • For most effective cleaning, keep nozzle from 8 to 24 inches (20 to 61 cm) away from cleaning surface. • If you get nozzle too close, especially using a high pressure nozzle, you may damage surface being cleaned. Pressure Washer Rinsing • Do Not get closer than 6 inches (15 cm) when cleaning tires.
SPECIFICATIONS Pressure Washer Specifications Max. Outlet Pressure ....................................3200 PSI* @ 2.5 GPM Max. Flow Rate..............................................2400 PSI @ 2.7 GPM* Chemical Mix...............…………....................Use as directed Water Supply Temperature............................Not to Exceed 100°F Engine Specifications Bore .........................……………...................2.8 in. (70 mm) Stroke ........................................................... 2.1 in.
MAINTENANCE OWNER'S RESPONSIBILITIES NOTE: Once a year you should clean or replace the spark plug and replace the air filter. A new spark plug Follow the hourly or calendar intervals, whichever occurs first. More frequent service is required when operating in adverse conditions noted below. and clean air filter assure proper fuel-air mixture and help your engine run better and last longer. Pump Oil First 5 Hours DO NOT attempt any oil maintenance on this pump.
Check and Clean Inlet Screen To remove contaminants from the pump, follow these steps: Examine garden hose inlet screen. Clean if it is clogged or replace if it is torn. Please call help line 1-866-902-9690 for new purchase. • Set up the pressure washer as described in the "Assembly" section and connect water supply. • Remove the nozzle from the spray wand . • Start the engine according to instructions in "How To Use Your Pressure Washer" section. • Squeeze the trigger on the gun and hold.
3. Verify oil is at FULL mark (top hole) on dipstick. Replace and tighten dipstick. WARNING The high pressure stream of water that this pressure washer produces could cut through skin and its underlying tissues, resulting in serious injury and possible amputation. • NEVER repair leaking connections with sealant of any kind. replace o-ring or seal. ENGINE MAINTENANCE WARNING Unintentional sparking could cause fire or electric shock resulting in death or serious injury.
from the spark plug. When crankcase is empty, return the pressure washer to upright position. 5. Slowly pour recommended oil (about 20 oz. (0.6 I)) into oil fill opening. Pause to permit oil to settle. Fill to Full mark (top hole) on dipstick. 6. Wipe dipstick clean each time oil level is checked. DO NOT overfill. 7. Replace and tighten dipstick. 8. Wipe up any remaining oil. 9. Reconnect spark plug wire to spark plug. 6. Install spark plug, tighten securely.
Carburetor Adjustment 6.Store the spray gun, wand like below. The carburetor on this engine is low emission. It is equipped with a non-adjustable idle mixture valve. Top speed has been set at the factory. If adjustment is required, see an authorized service dealer. CAUTION! Excessively high operating speeds could result in minor injury. Excessively low speeds impose a heavy load. • DO NOT tamper with governor spring, links or other parts to increase engine speed.
STORAGE WINTER STORAGE Oil Cylinder Bore 1. Remove spark plug. Squirt about 1 tablespoon of clean engine oil into the cylinder. Cover spark plug hole with rag. Pull recoil handle slowly to distribute oil. Avoid spray from spark plug hole. CAUTION You must protect your pressure washer from freezing temperatures. • Failure to do so will permanently damage your pump and render your unit inoperable. 2. Install spark plug. Do Not connect spark plug wire. • Freeze damage is not covered under warranty.
TROUBLESHOOTING Problem Pump has following problems. No pressure, low pressure Cause 1.Nozzle tip not attached. 1. Attached required nozzle tip 2. Water inlet is blocked. 2. Clear inlet. 3. Inadequate water supply. 3. Provide adequate water flow. 4. Inlet hose is kinked or leaking. 4. Straighten inlet hose, patch leak. 5. Clogged inlet hose strainer 5. Check and clean inlet hose strainer. 6. Water supply is over 100°F. 6. Provide cooler water supply. 7. High pressure hose is blocked or leaks.
NOTES 23
PARTS Yard Force 3200PSI Gas Pressure Washer Y0GWC3200R0 Main Unit — Exploded View To purchase replacement parts, call 1-866-902-9690.
Yard Force 3200PSI Gas Pressure Washer Y0GWC3200R0 Main Unit — Parts List Item 1 2 3 4 5 6 7 Part # 75496001 75496002 75496003 75496004 75496005 75496006 75496007 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 75496008 75496009 75496010 75496011 75496012 75496013 75496014 75496015 75496016 75496017 75496018 75496019 75496020 75496021 75496022 75496023 24 25 26 27 28 29 30 31 32 33 34 75496024 75496025 75496026 75496027 75496028 75496029 75496030 75496031 75496032 75496033 75496034 35 36 75496035 75496
ENGINE, 7 HP, JFNT210 for Pressure Washer Y0GWC3200R0 - Exploded View To purchase replacement parts, call 1-866-902-9690.
ENGINE, 7 HP, JFNT210 for Pressure Washer Y0GWC3200R0 - Parts List Item 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 Part # 7549604801 7549604802 7549604803 7549604804 7549604805 7549604806 7549604807 7549604808 7549604809 7549604810 7549604811 7549604812 7549604813 7549604814 7549604815 7549604816 7549604817 7549604818 7549604819 7549604820 7549604821 7549604822 7549604823 7549604824 7549604825 7549604826 7549604827 7549604828 7549
EMISSION CONTROL SYSTEM WARRANTY California, U.S. EPA, and Yardforce Emissions Control Warranty Statement Yardforce Emissions Control Warranty Provisions The following are specific provisions relative to your Emissions Control Warranty Coverage. It is in addition to the Yardforce engine warranty for non-regulated engines found in the Operator's Manual. Your Warranty Rights And Obligations The California Air Resources Board, U.S. EPA, and Merotec Inc.
The warranty on emissions-related parts is as follows: • Any warranted part that is not scheduled for replacement as required maintenance in the Operator's Manual supplied, is warranted for the warranty period stated above. If any such part fails during the period of warranty coverage, the part will be repaired or replaced by Merotec at no charge to the owner. Any such part repaired or replaced under the warranty will be warranted for the remaining warranty period.
WARRANTY YARDFORCE TWO YEAR LIMITED WARRANTY Product Warranty Please keep your original purchase receipt in a safe place as proof of purchase. Warranty coverage for this product must be verified by the original purchase receipt. The warranty period begins on the day that the product was purchased from an authorized retailer of Yard Force products. Warranty coverage only applies to the original purchaser and is not transferrable.
Merotec Inc. 3655 Kennesaw North Industrial Parkway, Kennesaw, GA 30144 Copyright © 2017 Merotec Inc.
