Instructions / Assembly

ManualsBrandsYARD FORCE ManualsLawn Mowers28-Volt 8 in. Cutting Width Robot Lawn Mower Revola X4E Mower, Brushless Wheel Motors, CloudHawk App and Wifi Control

10 11

Hotline: 1-866-902-9690 Hotline: 1-866-902-9690

PARTS LIST

KNOW YOUR TILLER

1. STOP button

2. Ultrasonic sensor

3. Charging inlet

4. Rear wheel

5. Height adjustment dial

6. Control panel

7. Blade plate

8. Power switch button

9. Firmware update port

SCOPE OF DELIVERY

INTENDED USE

The Robotic Mower is exclusively designed for mowing lawns. It is only intended for private use and is not

suitable for commercial use.

Any other use that is not specically approved in these instructions can result in damage to the Robotic

Mower and could be a serious danger to the user.

This appliance MUST NOT be used by children and persons with reduced physical, sensory or mental

capabilities or lack of experience and knowledge, unless they have been given supervision or instruction

concerning use of the appliance by a person responsible for their safety.

Children should be supervised to ensure that they do not play with the appliance.

The owner or operator is responsible for accidents or harm to others people and their property.

The manufacturer cannot be held liable for damage caused by other incorrect operation of the Robotic

Mower or if it is not used in line with its intended purpose.

TECHNICAL SPECIFICATIONS

Model RVX4E

Max cutting area 1/2 Acre

Battery pack 28 V/ 4000 mAh

Switch power supply

Input: 100-120 VAC~, 50/60 Hz, 102 W

Output: 34V , 3A

Power supply model* FY3403000S3

Mowing time on one charge 100 min

Rated voltage 28 V

Rated power 50 W

No load speed 2850 min

-1

Cung width 9 in

Cutting height 1-1/3"-3"

Charging time 80 min

Blade model 846210

Weight 29.3 lb

Frequency Band 0-148.5 kHz

Magnetic Field Strength 70 dBμA/m

Wifi Frequency Band 2400~2483.5MHz

Wifi Magnetic Field strength 20dBm

Max sound pressure level L

=53 dB, K=3 dB

Max sound power level L

=64 dB, K=3 dB

Degree of protection:

Robotic Mower IP24

Switching power supply IP67, Plug IP44

Spare parts

Spare Blades 9 Pcs

Boundary pegs 300 Pcs

Boundary wire 800'

Connectors 9 Pcs

* WARNING: For the purposes of recharging the battery, only use the detachable supply unit provided with

this appliance.

Robotic Mower

Wire pegs

Manuals

Spare blades

Extension cordDocking station

Connectors

Measurement ruler

Boundary wire

Switching Power Supply

Summary of content (5 pages)

PAGE 1
INTENDED USE PARTS LIST KNOW YOUR TILLER 1 2 5 6 3 4 The Robotic Mower is exclusively designed for mowing lawns. It is only intended for private use and is not suitable for commercial use. Any other use that is not specifically approved in these instructions can result in damage to the Robotic Mower and could be a serious danger to the user.
PAGE 2
ASSEMBLY ASSEMBLY Installation Guide This chapter explains how to install the Robotic Mower. Please read this completely before you start the installation. Introduction We recommend creating a drawing of your lawn, including all obstacles and how these should be protected. This makes it easier to find a good position for the docking station and how to correctly place the boundary wire around your garden perimeter protecting bushes, flower beds etc.
PAGE 3
ASSEMBLY ASSEMBLY If your lawn has a soft or uneven surface, we recommend fortifying the area around the docking station with a grass protection mesh. Otherwise, the repeated stress of the rear wheels can damage the turf. Once the position of the docking station is confirmed and mains electrical connection is laid out, please do not connect to main power yet. Finish all boundary layout work before connecting the docking station to the power supply.
PAGE 4
ASSEMBLY ASSEMBLY Flowerbeds Inventory and garage Use the boundary wire to exclude any flowerbeds from the cutting area. There are two options for the two lengths of boundary wire running between the flowerbed and the outer boundary: 1) Keep the distance between the parallel wires above 2 in. This way, the Robotic Mower will recognise the boundary wire as an ordinary obstacle. When cutting, it will "bounce" off it as usual.
PAGE 5
ASSEMBLY ASSEMBLY Press the buttons and OK button, then close the lid, a few seconds later, Mower should automatically return to the docking station by locating and following the boundary wire in anti- clockwise direction. If Robotic Mower fails to dock correctly, move the docking station to a more suitable position.