User`s manual

18
CHAPTER2 CC-Link Unit
SO216
SO217
SO218
SO219
SO220
SO221
SO222
SO223
SO224
SO225
SO226
SO227
SO228
SO229
SO230
SO231
Reserved
Initial data request flag
Not Used
Error flag
Remote READY
Reserved
RX(n+2)0
RX(n+2)1
RX(n+2)2
RX(n+2)3
RX(n+2)4
RX(n+2)5
RX(n+2)6
RX(n+2)7
RX(n+2)8
RX(n+2)9
RX(n+2)A
RX(n+2)B
RX(n+2)C
RX(n+2)D
RX(n+2)E
RX(n+2)F
RX(n+3)0
RX(n+3)1
RX(n+3)2
RX(n+3)3
RX(n+3)4
RX(n+3)5
RX(n+3)6
RX(n+3)7
RX(n+3)8
RX(n+3)9
RX(n+3)A
RX(n+3)B
RX(n+3)C
RX(n+3)D
RX(n+3)E
RX(n+3)F
SI216
SI217
SI218
SI219
SI220
SI221
SI222
SI223
SI224
SI225
SI226
SI227
SI228
SI229
SI230
SI231
Reserved
Initial data end flag
Not Used
Reserved
RY(n+2)0
RY(n+2)1
RY(n+2)2
RY(n+2)3
RY(n+2)4
RY(n+2)5
RY(n+2)6
RY(n+2)7
RY(n+2)8
RY(n+2)9
RY(n+2)A
RY(n+2)B
RY(n+2)C
RY(n+2)D
RY(n+2)E
RY(n+2)F
RY(n+3)0
RY(n+3)1
RY(n+3)2
RY(n+3)3
RY(n+3)4
RY(n+3)5
RY(n+3)6
RY(n+3)7
RY(n+3)8
RY(n+3)9
RY(n+3)A
RY(n+3)B
RY(n+3)C
RY(n+3)D
RY(n+3)E
RY(n+3)F
OUTPUT (Remote→Master) INPUT (Master→Remote)
Device No. Signal Name Device No. Signal Name
n: Value determined by station number settin
g
.
* Use RXn0-RXnF as dedicated outputs, RX(n+1)0 - RX(n+2)F as general-purpose out-
puts, RYn0 - RYnF as dedicated inputs, and RY(n+1)0 - RY(n+2)F as general-purpose
inputs.
* RX(n+3) 0 - RX(n+3)F and RY(n+3) 0 - RY (n+3)F are areas reserved for the CC-Link
system.
!
CAUTION
•The above profile is for cases where the I/O assignment selection parameter is
set to "Type 0: Conventional type" when the controller has an I/O assignment
function. For information on the profile when the I/O assignment selection pa-
rameter is set to another type, refer to "2-9-2 I/O assignment list".
•The zone output is supported by the following controller versions:
ERCX, SRCX : Ver. 13.50 or later DRCX : Ver. 18.50 or later
SRCP, SRCD : Ver. 24.00 or later SRCP30 : Ver. 24.30H or later