User Manual
Table Of Contents
- How to Use This Reference Manual
- Contents
- Function Tree
- SELECTED CHANNEL section
- Centralogic section
- Input and output patching
- Input channels
- Signal flow for input channels
- Specifying the channel name, icon and channel color
- Making HA (Head Amp) settings
- Sending a signal from an input channel to the STEREO/MONO buses
- Sending a signal from an input channel to a MIX/ MATRIX bus
- Correcting delay between channels (Input Delay)
- Channel library operations
- Output channels
- EQ and Dynamics
- Grouping and linking
- Scene memory
- About scene memories
- Using scene memories
- Editing scene memories
- Using the Global Paste function
- Using the Focus function
- Using the Recall Safe function
- Using the Fade function
- Outputting a control signal to an external device in tandem with scene recall (GPI OUT)
- Playing back an audio file that links to a scene recall
- Using Preview mode
- Monitor and Cue functions
- Talkback and Oscillator
- Meters
- Graphic EQ, effects, and Premium Rack
- I/O device and external head amp
- MIDI
- User settings (Security)
- Recorder
- Help function
- Other functions
- About the SETUP screen
- Word clock and slot settings
- Using cascade connections
- Basic settings for MIX buses and MATRIX buses
- Switching the entire phantom power supply on/ off
- Specifying the brightness of the touch screen, LEDs, channel name displays, and lamps
- Setting the date and time of the internal clock
- Setting the network address
- Initializing the unit to factory default settings
- Adjusting the detection point of the touch screen (Calibration function)
- Adjusting the faders (Calibration function)
- Fine-tuning the input and output gain (Calibration function)
- Adjusting the channel color (Calibration function)
- Adjusting the brightness of the channel name display
- Adjusting the contrast of the channel name display
- Dante audio network settings
- Using GPI (General Purpose Interface)
- Appendices
- EQ Library List
- DYNAMICS Library List
- Dynamics Parameters
- Effect Type List
- Effects Parameters
- Premium Rack Processor Parameters
- Effects and tempo synchronization
- Parameters that can be assigned to control changes
- NRPN parameter assignments
- Mixing parameter operation applicability
- Functions that can be assigned to USER DEFINED keys
- Functions that can be assigned to USER DEFINED knobs
- Functions that can be assigned to the assignable encoders
- MIDI Data Format
- Warning/Error Messages
- Electrical characteristics
- Mixer Basic Parameters
- M IDI Implementation Chart
- Index
Output channels
Reference Manual
52
Using the Centralogic section
This method lets you use the multifunction knobs (in the Centralogic section) to simultaneously adjust
the send levels from the eight channels selected in the Centralogic section to the desired MATRIX bus.
1. Make sure that an output port is assigned to the MATRIX bus to which you want
to send signals, and that your external device is connected to the corresponding
output port.
2. Use the Bank Select keys in the Centralogic section to access the OVERVIEW screen
that includes the channels (MIX channels or STEREO/MONO channels) that you
want to control.
In the OVERVIEW screen, you can use the TO MATRIX field to adjust the send levels to the
MATRIX bus.
3. Press the TO MATRIX SEND LEVEL knob for the desired send-destination MATRIX
bus.
A bold frame will appear around all TO MATRIX SEND LEVEL knobs for that MATRIX bus.
4. Use multifunction knobs 1–8 to adjust the send level of the signals sent from up to
eight MIX channels or the STEREO/MONO channels to the selected MATRIX bus.
If necessary, you can use the Bank Select keys and the [SEL] keys in the Centralogic section to
switch the send-source channel.
NOTE
• If you want to monitor signals being sent to a specific MATRIX bus, use the Bank Select keys to
access the corresponding MATRIX channel in the Centralogic section, and then press the [CUE]
key for that MATRIX channel.
• If you again press the currently-selected MATRIX bus select button, cue monitoring will be turned
on for the related MATRIX channel. This method is convenient if you want to monitor a signal that
is being sent to the selected MATRIX bus.
5. If you want to make detailed settings for MATRIX sends, press the TO MATRIX
SEND LEVEL knob inside the bold frame once again.
When you press the currently-selected TO MATRIX SEND LEVEL knob a second time, the
MATRIX SEND popup window will appear. The window includes the following items.
1 ALL PRE button
Sets the send point to “PRE.” (The send point is the point at which signals are sent from all send-
source channels — including the input and output channels — to the selected send destination.)
2 ALL POST button
Sets the send point to “POST.” (The send point is the point at which signals are sent from all send-
source channels — including the input and output channels — to the selected send destination.)
3 SEND FROM MODE button
Press this button to switch to the “SEND from 8ch” popup window.
4 Send destination indicator
Indicates the currently-selected send destination.
14 2 3
0
9
8
7
6
5