Owner`s manual

Warning/Error Messages
Reference Manual
216
Monitor Assignment is Restricted to
Max. 8 Sources!
The Monitor Define function allows a maximum of eight sources to
be selected, but you attempted to assign more than eight.
No Access From Recorder!
In the RECORDER screen, it is not possible to move to a level higher
than \YPE\SONGS\.
No Channel Selected. A copy-source channel was not selected in the GLOBAL PASTE screen.
No Copy Item Selected.
In the GLOBAL PASTE screen, you attempted to paste without having
selected an item to paste.
No Corresponding Help Items. The corresponding section was not found in the Help file.
No ID3 Tag exists. You can not edit. The music file cannot be edited because it has no ID3 tag.
No Response from External HA. No response from an external AD8HR.
No Response from I/O DEVICE. The I/O devices not responding.
Operating as the word clock master. The QL series is operating correctly as a word clock master.
Page Bookmarked. The current screen or popup has been bookmarked.
Parameter out of range! Some data could not be loaded because of a parameter mismatch.
Password Changed. The password has been changed.
PlayBack Failed: Recorder is Busy!
Audio file link playback is not possible because recording is in
progress.
PLAYBACK OUT CUE: Turned Off.
CUE was canceled for PLAYBACK OUT because you switched from the
RECORDER screen to another screen.
Please use Dante Controller. DANTE PATCH settings from the console are not enabled.
Please wait, Dante patch is proceeding
now.
You attempted to edit in the DANTE PATCH screen at a time when
patching was not possible.
Power Supply Fan has Malfunctioned!
The cooling fan of the internal power supply has stopped. Please
contact your Yamaha service center listed at the end of the Owner’s
Manual (separate document).
PREVIEW Mode : Cannot Use This
Function.
The operation was ignored because this function cannot be used
during Preview.
PREVIEW Mode : Disabled Preview was disabled.
PREVIEW Mode : Enabled Preview was enabled.
Processing Aborted. Processing was interrupted.
Recorder Busy: Operation Aborted!
Operation of the button was canceled because time is required for
recorder processing.
RECORDER: CODEC Error [0x%08X] ! A codec error occurred in the RECORDER screen.
RECORDER IN CUE: Turned Off.
CUE was canceled for RECORDER IN because you switched from the
RECORDER screen to another screen.
Re-Enter Password!
When specifying the user password, the password was not entered a
second time.
REMOTE: Data Framing Error!
REMOTE: Data Overrun!
An inappropriate signal has been input to the Remote connector.
REMOTE: Rx Buffer Full! Too much data has been received at the Remote connector.
REMOTE: Tx Buffer Full! Too much data has been transmitted from the Remote connector.
Removed from the Channel Link group. The channel was removed from the link group.
Message Meaning
Saving Aborted. Saving to the USB flash drive has been interrupted.
Saving Finished. Finished saving to USB flash drive.
SCENE #xxx is Empty!
No data has been stored in the scene you attempted to recall, or the
data has been damaged so that it cannot be recalled.
SCENE #xxx is Protected! You attempted to overwrite (store) a protected scene.
SCENE #xxx is Read Only! You attempted to overwrite (store) a read-only scene.
Scene Playback Link Canceled! The audio playback link for the scene was canceled.
SLOT x: Data Framing Error!
SLOT x: Data Overrun!
Invalid signals are being input to the SLOT x input port.
SLOT x: Rx Buffer Full! Too much data is being received at the SLOT x input port.
SLOT x: Tx Buffer Full! Too much data is being transmitted from the SLOT x output port.
Some Song Files Are Unidentified.
Some songs were not identified. Songs that have not been specified
might be used for DIRECT PLAY or SCENE PLAY BACK LINK.
Song File Not Found!
The file specified for SCENE LINK or DIRECT PLAY assigned to a USER
DEFINED key does not exist.
STAGEMIX: Data Framing Error!
STAGEMIX: Data Overrun!
Invalid signals are being exchanged with StageMix.
STAGEMIX: Rx Buffer Full! Too much data is being received at the StageMix input port.
STAGEMIX: Tx Buffer Full! Too much data is being transmitted from the StageMix output port.
Storage Full!
The file could not be saved because there is insufficient space on the
USB flash drive.
Storage Not Found! The USB flash drive could not be recognized.
Storage Not Ready! Access is not possible because the USB flash drive is not ready.
Sync Error! [xxx] The QL series console is not synchronized to the [xxx] signal.
Tap Operation Ignored.
Tap operation was ignored because the TAP TEMPO button is not
displayed in the screen.
This Operation is Not Allowed.
This operation has been ignored because the current user does not
have permission.
This page does not exist in this model.
You attempted to open a bookmark or window that does not exist in
the QL series.
Too Large Files! Loading Failed.
Loading is not possible because the bitmap file is too large. The
maximum supported file size is 307,256 Bytes.
Or loading is not possible because the bitmap file is too large. The
maximum supported file size is 1024 kilobytes.
Too Many Bands Used! Cannot
Compare.
Copying 31BandGEQ and comparing it to Flex15GEQ has failed
because more than 15 bands are included in the copy source.
Too Many Bands Used! Cannot Paste to
Flex15GEQ.
Copying and pasting 31BandGEQ to Flex15GEQ has failed because
more than 15 bands are included in the copy source.
Total Slot Power Capability Exceeded!
Power consumption of the I/O cards installed in the slots has
exceeded the rated value.
Unassigned Encoder.
Your operation has been ignored because there is no parameter that
corresponds to the knob you operated.
Unit Fan has Malfunctioned The fan of the R series has malfunctioned.
Message Meaning