Specifications
www.ellettbrothers.com
™
•Smallest & lightest hydraulic jack on the market - weighs
23 pounds •Perfect for shallow water skis & at boats
•Smallest footprint available: 14-5/8"W x 11-1/2"H
•Strong & fast actuator - 8 seconds top to boom •75 HP
outboards max.
AHJM-4-DP
Marine Catalog Page 665
$629.85
AtlAs
™
•Self-contained hydraulic pump system (V6 300hp Max) built
for today's powerful outboards, even the heaviest of 4-strokes
•No reservoir or lines to install •Boom to top in less than
8 seconds •Innovave rod and slot liing design - trouble
free liing acon •High-tech engineered polymer rods are 6
mes more abrasion-resistant than steel •Easy 2-pin pump
removal •Quick maintenance
AHJ-4V-DP 4" $878.75
AHJ-6V-DP 6" 891.25
AHJ-8V-DP 8" 1007.84
AHJ-10V-DP 10" 1020.78
AHJ-12V-DP 12" 1058.99
Marine Catalog Page 666
•Protects transoms from stress of engine when trailering •Heavy-wall tubing for strength
•Adjustable for boats with jack plates
AMS-1-DP
Marine Catalog Page 656
$23.75
•Polypropylene hold-down strap, locking quick
disconnect buckle •Molded base mounts with four
#10 pan head screws
BH-24P-DP 24/24M Series
BH-27P-DP 27/27M Series
BH-31P-DP 29/31 Series
Marine Catalog Page 521
$3.70
™
•Provides added safety & performance •All cast-aluminum
w/stainless steel hardware •Nylon & Teon
®
bushings on all
crical pivot points •Patented idle stop for FICHT & Opmax
engines •Requires longer throle cable (not included) •Fits:
Johnson/Evinrude, Mercury, Mariner, Honda, Yamaha & Chrysler
HF-1-DP
Marine Catalog Page 671
$84.60
™
•Inexpensive short transom x •Solid 3/8" aluminum extrusion
•3 engine mount holes, 2 transom holes •Total vercal of
5-1/2" •Max HP: 150
JP-4FA-DP
Marine Catalog Page 666
$91.45
™
•4" vercal height adjustment •6" setback •3/8" high
strength aluminum with polished mirror nish. •1-piece
design, top adjust •Locking bars allow one wrench adjust
•Handles all V6 outboards.
JP-6PW-DP
Marine Catalog Page 666
$207.40
™
™
•Full 1/2" thick aluminum material & Z-Lock
™
design
provides maximum strength •Design prevents side slippage
& movement •Easily adjusts up or down w/center bolt
•Handles all V6 outboards - 300hp Max.
JPZ-6-DP 6" $252.19
JPZ-8-DP 8" 301.22
JPZ-10-DP 10" 346.35
Marine Catalog Page 666
™
•Fits over trim rams •Supports outboard while trailering
•Takes the pressure o of hydraulic system •Strong
aluminum tubing w/molded ends •Salt or fresh water •Most outboards 150hp and up
MSS-1-DP
Marine Catalog Page 656
$22.75
•6061 T6 extruded aluminum alloy, stainless steel
fasteners •1-piece design •Centrally located
adjustment screw for convenience, posive alignment
•Can be adjusted from the top or the boom •5-
1/2" set-back from transom •5" vercal adjustment
•Designed to t standard BIA bolt paern w/o drilling or modicaons •For V-6 & smaller motors
65012
Marine Catalog Page 664
$252.29
•Incorporates a 6" setback which enhances boat
stability and enables the prop to get a beer "bite"
at a higher prop seng •With the touch of a
switch, you can raise the motor to protect the prop
from damage and also your back from strain •20º
of Trim and 90º of Trim & Tilt •Tuck your motor
in to get the boat on plane smoother and faster
•Change the angle of the motor to obtain the best
performance for your load and water condions
•Constructed of 1/2" 6061 T6 alloy aluminum extrusions and fastened w/stainless steel fasteners
•100% non-ferrous material which makes it impervious to saltwater and freshwater •Totally
waterproof marine electric hydraulic system that is rated over 7800 lbs. of thrust •Fits on
virtually any type of boat and outboard motor •Rated for 10hp-130hp motors and ts standard
B.I.A. bolt paern motors without drilling holes •OPTIONAL Tilt & Trim gauge is sealed, drip-
proof, mounts in dash •Sending unit is completely sealed & waterproof
13001 With Trim Gauge $674.00
13002 Without Trim Gauge 571.80
Marine Catalog Page 667