User Manual
Table Of Contents
- How to Use This Reference Manual
- Contents
- Function Tree
- SELECTED CHANNEL section
- Channel Strip section
- Input and output patching
- Input channels
- Signal flow for input channels
- Specifying the channel name, icon, and channel color
- Making HA (Head Amp) settings
- Sending the signal from an input channel to the STEREO/MONO bus
- Added pan function (Monaural input channels only)
- Sending a signal from an input channel to a MIX/ MATRIX bus
- Channel name display indication
- Correcting delay between channels (Input Delay)
- Surround output for input channels
- Channel library operations
- OUTPUT channels
- Signal flow for output channels
- Specifying the channel name, icon, and channel color
- Sending signals from MIX channels to the STEREO/ MONO bus
- Sending signals from MIX channels and STEREO/ MONO channels to MATRIX buses
- Correcting delay between channels (Output Delay)
- Using the PORT TO PORT function
- Channel library operations
- EQ and Dynamics
- Channel Job
- Scene memory
- Monitor and Cue functions
- Talkback and Oscillator
- Meters
- Graphic EQ, Parametric EQ, effects, and Premium Rack
- I/O devices and external head amps
- MIDI
- Recorder
- AFC IMAGE Control
- Setup
- About the SETUP screen
- User settings
- Preferences
- USER DEFINED keys
- Functions that can be assigned to USER DEFINED keys
- USER DEFINED knobs
- Functions that can be assigned to USER DEFINED knobs
- Custom fader bank
- Console Lock
- Saving and loading setup data to and from a USB flash drive
- Remount function to USB flash drives
- Word clock and slot settings
- Using cascade connections
- Basic settings for MIX buses and MATRIX buses
- Switching the entire phantom power supply on/ off
- Specifying the brightness of the touch screen, LEDs, channel name displays, and lamps
- Setting the date and time of the internal clock
- Setting the network address
- Setting up the Dante audio network
- Dante Device Lock
- Support for Dante Domain Manager
- Using GPI (General Purpose Interface)
- Help function
- Other functions
- Initializing the unit to factory default settings
- Adjusting the detection point of the touch screen (Calibration function)
- Adjusting the faders (Calibration function)
- Fine-tuning the input and output gain (Calibration function)
- Adjusting the LED color (Calibration function)
- Adjusting the brightness of the channel name display
- Adjusting the contrast of the channel name display
- Initializing the Dante audio network settings
- Update procedure for NAME SUB CPU firmware
- Update function to Dante firmware
- Warning/Error Messages
- Index
- Data List
- Table of Contents
- EQ Library List
- DYNAMICS Library List
- Dynamics Parameters
- Effect Type List
- Effects Parameters
- Premium Rack Processor Parameters
- Parameters That Can Be Assigned to Control Changes
- NRPN Parameter Assignments
- Mixing Parameter Operation Applicability
- MIDI Data Format
- Input/Output Characteristics
- Electrical Characteristics
- Mixer Basic Parameters
- Pin Assignment
- MIDI Implementation Chart
Input channels
V5.8 Reference Manual
29
2 HA section (If patched to a wireless mic)
•Frequency
Indicates the frequency that is currently set for the RF signal.
• Signal quality meter
Displays the quality of the received RF signal. The vertical axis represents quality and the
horizontal axis represents time, and the display of connection status is updated every
second. If you move away from the transmitter, or the quality of the RF signal decreases
due to the influence of disturbing radio waves, the bar indication becomes lower. It
displays in purple for Shure devices, and in white for the other developer’s devices.
• RX.GAIN knob/TX.GAIN knob/TX.ATT knob
Sets the HA gain for the transmitter or receiver. The level meter located at the immediate
right of the knob indicates the input level.
The knob name will change depending on the connected device.
• MUTE indicator
Indicates the mute status (on/off) of the audio signal for the receiver.
• RF (Radio Frequency) signal meter
Shows bars to indicate the level of the RF signal.
An active antenna indicator is shown on the right side. It indicates which antenna is
enabled by lighting up.
NOTE
For more information about the relationship between the number of bars and the actual strength
of the RF signal, refer to the manual from each developer.
• Battery indicator
Shows bars to indicate the remaining battery power.
NOTE
For more information about the relationship between the number of bars and maximum operation
time, refer to the manual from each developer.
3 INPUT PORT button
Indicates the port that is assigned to the channel. Press this button to display the PORT
SELECT window, in which you can select a port to patch.
4 Icon/Channel name button
Indicates the channel number, icon, and name. Press this button to access the PATCH/
NAME window, in which you can patch the input port and specify the channel name.
5 AG-DG LINK button
Turns the analog gain and digital gain link on or off. When the link is turned on, the
digital gain is linked to adjustments made to the analog gain, even if Gain
Compensation is on.
6 Ø (Phase) button
Switches between normal and reverse phase settings of signals input.
7 D. GAIN (digital gain) knob
Indicates the digital gain value. You can use the [TOUCH AND TURN] knob to adjust the
digital gain. If the Gain Compensation function is turned on, no changes will be made
to the input level of the analog gain, and therefore the input gain is adjusted with the
digital gain.
8 Digital gain meter
Indicates the level after the signal passes through the digital gain.
9 GC ALL ON button/GC ALL OFF button
Switch Gain Compensation on or off for all input channels simultaneously.
0 AG-DG ALL ON button/AG-DG ALL OFF button
Switch all analog gain and digital gain links on or off simultaneously.