User Manual
Table Of Contents
- How to Use This Reference Manual
- Contents
- Function Tree
- SELECTED CHANNEL section
- Channel Strip section
- Input and output patching
- Input channels
- Signal flow for input channels
- Specifying the channel name, icon, and channel color
- Making HA (Head Amp) settings
- Sending the signal from an input channel to the STEREO/MONO bus
- Added pan function (Monaural input channels only)
- Sending a signal from an input channel to a MIX/ MATRIX bus
- Channel name display indication
- Correcting delay between channels (Input Delay)
- Surround output for input channels
- Channel library operations
- OUTPUT channels
- Signal flow for output channels
- Specifying the channel name, icon, and channel color
- Sending signals from MIX channels to the STEREO/ MONO bus
- Sending signals from MIX channels and STEREO/ MONO channels to MATRIX buses
- Correcting delay between channels (Output Delay)
- Using the PORT TO PORT function
- Channel library operations
- EQ and Dynamics
- Channel Job
- Scene memory
- Monitor and Cue functions
- Talkback and Oscillator
- Meters
- Graphic EQ, Parametric EQ, effects, and Premium Rack
- I/O devices and external head amps
- MIDI
- Recorder
- AFC IMAGE Control
- Setup
- About the SETUP screen
- User settings
- Preferences
- USER DEFINED keys
- Functions that can be assigned to USER DEFINED keys
- USER DEFINED knobs
- Functions that can be assigned to USER DEFINED knobs
- Custom fader bank
- Console Lock
- Saving and loading setup data to and from a USB flash drive
- Remount function to USB flash drives
- Word clock and slot settings
- Using cascade connections
- Basic settings for MIX buses and MATRIX buses
- Switching the entire phantom power supply on/ off
- Specifying the brightness of the touch screen, LEDs, channel name displays, and lamps
- Setting the date and time of the internal clock
- Setting the network address
- Setting up the Dante audio network
- Dante Device Lock
- Support for Dante Domain Manager
- Using GPI (General Purpose Interface)
- Help function
- Other functions
- Initializing the unit to factory default settings
- Adjusting the detection point of the touch screen (Calibration function)
- Adjusting the faders (Calibration function)
- Fine-tuning the input and output gain (Calibration function)
- Adjusting the LED color (Calibration function)
- Adjusting the brightness of the channel name display
- Adjusting the contrast of the channel name display
- Initializing the Dante audio network settings
- Update procedure for NAME SUB CPU firmware
- Update function to Dante firmware
- Warning/Error Messages
- Index
- Data List
- Table of Contents
- EQ Library List
- DYNAMICS Library List
- Dynamics Parameters
- Effect Type List
- Effects Parameters
- Premium Rack Processor Parameters
- Parameters That Can Be Assigned to Control Changes
- NRPN Parameter Assignments
- Mixing Parameter Operation Applicability
- MIDI Data Format
- Input/Output Characteristics
- Electrical Characteristics
- Mixer Basic Parameters
- Pin Assignment
- MIDI Implementation Chart
Input channels
V5.8 Reference Manual
28
Making HA (Head Amp) settings
You can make HA (Head Amp) related settings (phantom power on/off, gain, phase) for the
input channel.
• To adjust only the HA analog gain, use the [TOUCH AND TURN] knob.
Setting the gain
Head amp settings are made in the GAIN/PATCH window.
NOTE
• The PAD will be switched on or off internally when the HA gain is adjusted between +17 dB and
+18 dB.
• Keep in mind that noise may be generated when using phantom power if there is a difference
between the Hot and Cold output impedance of an external device connected to the INPUT jack.
• The GAIN knob, +48V button, and Ø button are valid only on channels for which the assigned
input port is an INPUT jack on the I/O device, the INPUT jack on the QL unit, or a slot that is
connected to an external head amp device (e.g., Yamaha AD8HR or SB168-ES).
GAIN/PATCH window (1ch)
1 Channel icon/Channel number/Channel name indicator
Indicates the channel icon, number, and name.
2 HA section
Appears if the head amp is patched to the input channel.
NOTE
• If a slot is patched to the channel, the type of the slot/MY card and the slot meter will be displayed.
• If a rack is patched, the type of rack and type of effect will be displayed.
• +48V button
Switches head amp phantom power (+48V) on or off.
• A.GAIN (analog gain) knob
Indicates the analog gain of the head amp. You can use the [TOUCH
AND TURN] knob to adjust the gain. If the Gain Compensation function
is turned on, an indicator will appear, showing the position of the
analog gain when the function is turned on.
•HA meter
Displays the level of the HA input signal.
• GC (Gain Compensation) ON/OFF button
Turns the Gain Compensation (gain correction function) on or off. If the Gain
Compensation function is turned on, the level of the signal output from the I/O device
to the audio network will be stabilized. For example, if the FOH console and the
monitoring console are sharing an I/O device, or if you are performing digital recording
via Dante connections, using this function will maintain the signal output at a constant
level from the I/O device to the network even if the analog gain value on the I/O device
is changed. If the Gain Compensation button is turned off, the compensation gain will
be reset, while the analog gain will return to the level that was obtained before you
turned on the button. Therefore, the signal level on the digital network will remain the
same.
• Gain compensation meter
Indicates the level of the signal output to the audio network after gain compensation.
STEP
1. Press the Bank Select keys in the Fader Bank section and the [SEL] keys on the top
panel to select the channel.
2. Press the GAIN knob in the GAIN/PATCH field in the SELECTED CHANNEL VIEW
screen.
3. Press the 1ch or 8ch tab in the GAIN/PATCH window.
4. Make settings for the head amp.
SELECTED CHANNEL VIEW screen GAIN/PATCH window (1ch)
01 9
32 54 687