User Manual
Table Of Contents
- How to Use This Reference Manual
- Contents
- Function Tree
- SELECTED CHANNEL section
- Channel Strip section
- Input and output patching
- Input channels
- Signal flow for input channels
- Specifying the channel name, icon, and channel color
- Making HA (Head Amp) settings
- Sending the signal from an input channel to the STEREO/MONO bus
- Added pan function (Monaural input channels only)
- Sending a signal from an input channel to a MIX/ MATRIX bus
- Channel name display indication
- Correcting delay between channels (Input Delay)
- Surround output for input channels
- Channel library operations
- OUTPUT channels
- Signal flow for output channels
- Specifying the channel name, icon, and channel color
- Sending signals from MIX channels to the STEREO/ MONO bus
- Sending signals from MIX channels and STEREO/ MONO channels to MATRIX buses
- Correcting delay between channels (Output Delay)
- Using the PORT TO PORT function
- Channel library operations
- EQ and Dynamics
- Channel Job
- Scene memory
- Monitor and Cue functions
- Talkback and Oscillator
- Meters
- Graphic EQ, Parametric EQ, effects, and Premium Rack
- I/O devices and external head amps
- MIDI
- Recorder
- AFC IMAGE Control
- Setup
- About the SETUP screen
- User settings
- Preferences
- USER DEFINED keys
- Functions that can be assigned to USER DEFINED keys
- USER DEFINED knobs
- Functions that can be assigned to USER DEFINED knobs
- Custom fader bank
- Console Lock
- Saving and loading setup data to and from a USB flash drive
- Remount function to USB flash drives
- Word clock and slot settings
- Using cascade connections
- Basic settings for MIX buses and MATRIX buses
- Switching the entire phantom power supply on/ off
- Specifying the brightness of the touch screen, LEDs, channel name displays, and lamps
- Setting the date and time of the internal clock
- Setting the network address
- Setting up the Dante audio network
- Dante Device Lock
- Support for Dante Domain Manager
- Using GPI (General Purpose Interface)
- Help function
- Other functions
- Initializing the unit to factory default settings
- Adjusting the detection point of the touch screen (Calibration function)
- Adjusting the faders (Calibration function)
- Fine-tuning the input and output gain (Calibration function)
- Adjusting the LED color (Calibration function)
- Adjusting the brightness of the channel name display
- Adjusting the contrast of the channel name display
- Initializing the Dante audio network settings
- Update procedure for NAME SUB CPU firmware
- Update function to Dante firmware
- Warning/Error Messages
- Index
- Data List
- Table of Contents
- EQ Library List
- DYNAMICS Library List
- Dynamics Parameters
- Effect Type List
- Effects Parameters
- Premium Rack Processor Parameters
- Parameters That Can Be Assigned to Control Changes
- NRPN Parameter Assignments
- Mixing Parameter Operation Applicability
- MIDI Data Format
- Input/Output Characteristics
- Electrical Characteristics
- Mixer Basic Parameters
- Pin Assignment
- MIDI Implementation Chart
Setup
V5.8 Reference Manual
264
NOTE
• With latched operation, the function will switch between active and inactive each time a trigger is
input from the external switch. In this case, we recommend that you use a non-locking type of
external switch.
• With unlatched operation, the function will be active only while the signal from the external switch
is at the high level or low level. In this case, you may use either a non-locking or a locking type
of external switch as appropriate for your needs.
• Settings in the GPI page of the MIDI/GPI screen are common to all scenes. They can be saved
as SETUP data.
MIDI/GPI screen (GPI page)
1 GPI IN status indicator
This indicates the status of the voltage being input to the GPI IN port.
2 Switch attribute select button
This button selects the switch attribute. Each time you press the button, its indication
will alternate between LATCH and UNLATCH.
................. LATCH (a switch that alternately turns on/off each time it is pressed)
is selected.
................. UNLATCH (a switch that is on only while pressed and is off when
released) is selected.
3 POLARITY MODE select button
This button selects the polarity of the GPI IN port.
..................... (Low active) When operating an on/off-type parameter, it will
become active when the switch is grounded.
..................... (High active) When operating an on/off-type parameter, it will
become active when the switch is opened or when a high-level
voltage is input.
4 GPI IN SETUP button
The button shows the name of the currently-selected function or parameter. Press this
button to display the GPI IN SETUP window.
NOTE
The items that can be selected in the GPI IN SETUP window are the same as for the USER
DEFINED keys (page 221).
Using GPI OUT
The GPI OUT ports of the GPI OUT connector allow you to control an external device by
performing operations on the QL series console.
1
2
3
4
STEP
1. Connect an external device to the QL series console’s GPI connector.
2. In the Function Access Area, press the SETUP button.
3. In the SETUP screen, press the MIDI/GPI button.
4. In the MIDI/GPI screen, press the GPI tab.
5. Specify the POLARITY MODE for each port as appropriate for the specifications of
the external device you’re using.
6. To assign a function or parameter that you want to control, press the GPI OUT
SETUP button.
7. In each field of the GPI OUT SETUP window, select the desired function and
parameter, then press the OK button.