User Manual
Table Of Contents
- How to Use This Reference Manual
- Contents
- Function Tree
- SELECTED CHANNEL section
- Channel Strip section
- Input and output patching
- Input channels
- Signal flow for input channels
- Specifying the channel name, icon, and channel color
- Making HA (Head Amp) settings
- Sending the signal from an input channel to the STEREO/MONO bus
- Added pan function (Monaural input channels only)
- Sending a signal from an input channel to a MIX/ MATRIX bus
- Channel name display indication
- Correcting delay between channels (Input Delay)
- Surround output for input channels
- Channel library operations
- OUTPUT channels
- Signal flow for output channels
- Specifying the channel name, icon, and channel color
- Sending signals from MIX channels to the STEREO/ MONO bus
- Sending signals from MIX channels and STEREO/ MONO channels to MATRIX buses
- Correcting delay between channels (Output Delay)
- Using the PORT TO PORT function
- Channel library operations
- EQ and Dynamics
- Channel Job
- Scene memory
- Monitor and Cue functions
- Talkback and Oscillator
- Meters
- Graphic EQ, Parametric EQ, effects, and Premium Rack
- I/O devices and external head amps
- MIDI
- Recorder
- AFC IMAGE Control
- Setup
- About the SETUP screen
- User settings
- Preferences
- USER DEFINED keys
- Functions that can be assigned to USER DEFINED keys
- USER DEFINED knobs
- Functions that can be assigned to USER DEFINED knobs
- Custom fader bank
- Console Lock
- Saving and loading setup data to and from a USB flash drive
- Remount function to USB flash drives
- Word clock and slot settings
- Using cascade connections
- Basic settings for MIX buses and MATRIX buses
- Switching the entire phantom power supply on/ off
- Specifying the brightness of the touch screen, LEDs, channel name displays, and lamps
- Setting the date and time of the internal clock
- Setting the network address
- Setting up the Dante audio network
- Dante Device Lock
- Support for Dante Domain Manager
- Using GPI (General Purpose Interface)
- Help function
- Other functions
- Initializing the unit to factory default settings
- Adjusting the detection point of the touch screen (Calibration function)
- Adjusting the faders (Calibration function)
- Fine-tuning the input and output gain (Calibration function)
- Adjusting the LED color (Calibration function)
- Adjusting the brightness of the channel name display
- Adjusting the contrast of the channel name display
- Initializing the Dante audio network settings
- Update procedure for NAME SUB CPU firmware
- Update function to Dante firmware
- Warning/Error Messages
- Index
- Data List
- Table of Contents
- EQ Library List
- DYNAMICS Library List
- Dynamics Parameters
- Effect Type List
- Effects Parameters
- Premium Rack Processor Parameters
- Parameters That Can Be Assigned to Control Changes
- NRPN Parameter Assignments
- Mixing Parameter Operation Applicability
- MIDI Data Format
- Input/Output Characteristics
- Electrical Characteristics
- Mixer Basic Parameters
- Pin Assignment
- MIDI Implementation Chart
Setup
V5.8 Reference Manual
232
Specifying the CONSOLE LOCK screen image
If an image file has been saved on the USB flash drive, you can view that image on the
CONSOLE LOCK screen.
In the SAVE/LOAD window, specify the image file that you want to display, and then load it
from the USB flash drive. For details about loading files from the USB flash drive, refer to
“Loading a file from a USB flash drive” on page 235.
NOTE
Supported image file format is BMP in 800 x 600 pixels and 16/24/32-bit, but they will be
converted into 16-bit for display.
Saving and loading setup data to and from a USB
flash drive
You can connect a commercially-available USB flash drive to the USB connector located to
the right of the display, and save the internal settings and user authentication keys of the QL
series console to the USB flash drive or load them from the USB flash drive.
NOTICE
An ACCESS indicator is shown in the Function Access Area while data is being accessed (saved,
loaded, or deleted). During this time, do not disconnect the USB port or power-off the QL unit.
Doing so may damage the data in the flash drive.
NOTE
• Operation is guaranteed only for USB flash drives.
• The operation of USB flash drives with capacities of up to 32GB has been verified. (However, this
does not necessarily guarantee the operation of all USB flash drives.) The FAT16 and FAT32
formats are supported. A USB flash drive with a capacity of 4GB or larger will be formatted in
FAT32, and a USB flash drive with a capacity of 2GB or smaller will be formatted in FAT16.
Basic operation
SAVE/LOAD window
The list will show the files and sub-directories that have been saved.
1 COPY button
Copies a file into a memory buffer (a temporary holding area).
2 PASTE button
Pastes the file that has been copied into a buffer memory.
3 DELETE button
Deletes the selected file or directory.
NOTE
A directory cannot be deleted unless it is empty. The message “Directory Not Empty!” will appear.
STEP
1. In the Function Access Area, press the SETUP button.
2. In the SETUP screen, press the SAVE/LOAD button.
3. Save/load/edit the data.
SETUP screen
1 2 3 45 6
7
8 9 0 A BC