User Manual
PM5D/PM5D-RH V2 / DSP5D Bedienungsanleitung Referenzteil
385
Informationen auf
dem Bildschirm
Funktions-
menü
Globale
Funktionen
Ausgangs-
funktionen
Eingangs-
funktionen
Anhänge
*1. Sensitivity is the lowest level that will produce an output of +4 dBu (1.23 V) or the nominal output level when the unit is set to maximum gain. (all faders
and level controls are maximum position.)
*2. XLR-3-31 type connectors are balanced. (1=GND, 2=HOT, 3=COLD)
* In these specifications, 0 dBu = 0.775 Vrms.
* All input AD converters are 24bit linear, 128 times (@48 kHz) oversampling.
* +48V DC (phantom power) is supplied to INPUT (1-48) XLR type connectors via one master and each individual software switches.
❏ Analog Output Characteristics (PM5D, PM5D-RH)
*1. XLR-3-32 type connectors are balanced. (1=GND, 2=HOT, 3=COLD)
*2. Phone jacks are balanced. (Tip=HOT, Ring=COLD, Sleeve=GND)
*3. PHONES stereo phone jacks are unbalanced. (Tip=LEFT, Ring=RIGHT, Sleeve=GND)
*4. There are switches inside the body to preset the maximum output level.
*5. INSERT OUTs are only provided for PM5D.
*6. The position of the level control is 10 dB lowered from Max.
* In these specifications, 0 dBu = 0.775 Vrms.
* All output DA converters are 24bit, 128 times (@48 kHz) oversampling.
❏ Analog Output Characteristics (DSP5D)
*1. XLR-3-32 type connectors are balanced. (1=GND, 2=HOT, 3=COLD)
*2. There are switches inside the body to preset the maximum output level.
* In these specifications, 0 dBu = 0.775 Vrms.
* All output DA converters are 24bit, 128 times (@48 kHz) oversampling.
❏ Digital Input Characteristics (PM5D, PM5D-RH)
❏ Digital Input Characteristics (DSP5D)
*1. CASCADE (D-Sub 68pin) Max. Cable length: 200 m@48 kHz, 50 m@96 kHz
*2. CASCADE (RJ-45) Max. Cable length is based on EtherSound standard.
Output
Terminals
Actual Source
Impedance
For Use With
Nominal
GAIN SW
*4
Output Level
Connector
Nominal Max. Before Clip
STEREO A,B [L,R] 75Ω 600Ω Lines
+24 dB (default) +4 dBu (1.23 V) +24 dBu (12.28 V)
XLR-3-32 Type
(Balanced)
*1
+18 dB –2 dBu (616 mV) +18 dBu (6.16 V)
MONITOR OUT
[L,R,C]
75Ω 600Ω Lines
+24 dB (default) +4 dBu (1.23 V) +24 dBu (12.28 V)
XLR-3-32 Type
(Balanced)
*1
+18 dB –2 dBu (616 mV) +18 dBu (6.16 V)
CUE OUT [L,R] 75Ω 600Ω Lines
+24 dB (default) +4 dBu (1.23 V) +24 dBu (12.28 V)
XLR-3-32 Type
(Balanced)
*1
+18 dB –2 dBu (616 mV) +18 dBu (6.16 V)
MATRIX OUT 1-8 75Ω 600Ω Lines
+24 dB (default) +4 dBu (1.23 V) +24 dBu (12.28 V)
XLR-3-32 Type
(Balanced)
*1
+18 dB –2 dBu (616 mV) +18 dBu (6.16 V)
MIX OUT 1-24 75Ω 600Ω Lines
+24 dB (default) +4 dBu (1.23 V) +24 dBu (12.28 V)
XLR-3-32 Type
(Balanced)
*1
+18 dB –2 dBu (616 mV) +18 dBu (6.16 V)
INSERT OUT 1-48 150Ω 10kΩ Lines — +4 dBu (1.23 V) +24 dBu (12.28 V)
Phone Jack (TRS)
(Balanced)
*2 *5
PHONES (x 2) 15Ω
8Ω Phones
—
75 mW
*6
150 mW
Stereo Phone Jack
(TRS) (Unbalanced)
*3
40Ω Phones
65 mW
*6
150 mW
Output Terminals
Actual Source
Impedance
For Use With
Nominal
GAIN SW
*2
Output Level
Connector
Nominal Max. before clip
OMNI OUT 1-24 75Ω 600Ω Lines
+24 dB
(default)
+4 dBu
(1.23 V)
+24 dBu
(12.28 V)
XLR-3-32 type (Balanced)
*1
+18 dB
–2 dBu
(616 mV)
+18 dBu
(6.16 V)
Terminal Format Data Length Level Connector
2TR IN DIGITAL
1 AES/EBU AES/EBU 24bit RS422
XLR-3-31 Type (Balanced)
*1
*1. XLR-3-31 type connectors are balanced. (1=GND, 2=HOT, 3=COLD)
2 AES/EBU AES/EBU 24bit RS422
XLR-3-31 Type (Balanced)
*1
3 COAXIAL IEC-60958 24bit 0.5Vpp/75Ω RCA Pin Jack
CASCADE IN — RS422 D-Sub Half Pitch Connector 68P (Female)
Terminal Format Data Length Level Connector
CASCADE IN
*1
— — RS422 D-Sub Half Pitch Connector 68P (Female)
CASCADE IN
*2
— — 100Base-TX RJ-45