User Manual

ManualsBrandsYamaha ManualsSynthesizersCP STAGE Series

CP4 STAGE/CP40 STAGE Data List

MIDI Data Format

(3-1-4) PROGRAM CHANGE

STATUS 1100nnnn (CnH) n = 0 - 15 CHANNEL NUMBER

PROGRAM NUMBER 0ppppppp p = 0 - 127

(3-1-5) CHANNEL AFTER TOUCH

STATUS 1101nnnn (DnH) n = 0 - 15 CHANNEL NUMBER

VALUE 0vvvvvvv v = 0 - 127 AFTER TOUCH VALUE

(3-1-6) PITCH BEND CHANGE

STATUS 1110nnnn (EnH) n = 0 - 15 CHANNEL NUMBER

LSB 0vvvvvvv PITCH BEND CHANGE LSB

MSB 0vvvvvvv PITCH BEND CHANGE MSB

Transmitted with a resolution of 7 bits.

(3-2) CHANNEL MODE MESSAGES

STATUS 1011nnnn (BnH) n = 0 - 15 CHANNEL NUMBER

CONTROL NUMBER 0ccccccc c = CONTROL NUMBER

CONTROL VALUE 0vvvvvvv v = DATA VALUE

(3-2-1) ALL SOUND OFF (CONTROL NUMBER = 78H, DATA VALUE = 0)

All the sounds currently played including the channel messages such as note-on and hold-on in a certain

channel are muted when receiving this message.

(3-2-2) RESET ALL CONTROLLERS (CONTROL NUMBER = 79H, DATA VALUE = 0)

Resets the values set for the following controllers.

PITCH BEND CHANGE 0 (center)

MODULATION 0 (minimum)

EXPRESSION 127 (maximum)

FOOT CONTROLLER 1 0 (minimum)

FOOT CONTROLLER 2 0 (minimum) *8

SUSTAIN SWITCH 0 (off)

SOSTENUTO SWITCH 0 (off)

RPN Not assigned; No change

Doesn’t reset the following data:

PROGRAM CHANGE, BANK SELECT MSB/LSB, VOLUME, PAN, HARMONIC CONTENT, RELEASE TIME,

ATTACK TIME, DECAY TIME, BRIGHTNESS, EFFECT1 DEPTH, EFFECT3 DEPTH, PORTAMENTO SWITCH,

PITCH BEND SENSITIVITY, FINE TUNING, COARSE TUNING

*8 For CP4 STAGE only

(3-2-3) ALL NOTE OFF (CONTROL NUMBER = 7BH, DATA VALUE = 0)

All the notes currently set to on in certain channel(s) are muted when receiving this message. However, if Sustain

or Sostenuto is on, notes will continue sounding until these are turned off.

(3-2-4) OMNI MODE OFF (CONTROL NUMBER = 7CH, DATA VALUE = 0)

Performs the same function as when receiving ALL NOTES OFF.

(3-2-5) OMNI MODE ON (CONTROL NUMBER = 7DH, DATA VALUE = 0)

Performs the same function as when receiving ALL NOTES OFF.

(3-2-6) MONO (CONTROL NUMBER = 7EH, DATA VALUE = 0..16)

Performs the same function as when receiving ALL SOUNDS OFF. If the 3rd byte (mono) is within 0 through 16,

the channel will be Mode 4 (m = 1).

(3-2-7) POLY (CONTROL NUMBER = 7FH, DATA VALUE = 0)

Performs the same function as when receiving ALL SOUNDS OFF. The channel will be Mode 3.

(3-3) REGISTERED PARAMETER NUMBER

STATUS 1011nnnn (BnH) n = 0 - 15 CHANNEL NUMBER

LSB 01100100 (64H)

RPN LSB 0ppppppp p = RPN LSB

(Refer to the table as shown below.)

MSB 01100101 (65H)

RPN MSB 0qqqqqqq q = RPN MSB

(Refer to the table as shown below.)

DATA ENTRY MSB 00000110 (06H)

DATA VALUE 0mmmmmmm m = Data Value

DATA ENTRY LSB 00100110 (26H)

DATA VALUE 0lllllll l = Data Value

First, designate the parameter using RPN MSB/LSB numbers. Then, set its value with data entry MSB/LSB.

RPN D.ENTRY

LSB MSB MSB LSB PARAMETER NAME DATA RANGE

00H 00H mmH --- PITCH BEND SENSITIVITY 00H - 18H (0 - 12 semitones)

01H 00H mmH llH MASTER FINE TUNE {mmH,llH}={00H,00H}-{40H,00H}-{7FH,7FH}

(-8192*100/8192) - 0 - (+8192*100/8192)

02H 00H mmH --- MASTER COARSE TUNE 28H - 40H - 58H (-24 - 0 - +24 semitones)

7FH 7FH --- --- RPN RESET

RPN numbers will be left not designated.

The internal values are not affected.

(3-4) NON-REGISTERED PARAMETER NUMBER

There are no applicable parameters.

(3-5) SYSTEM REAL TIME MESSAGES

(3-5-1) ACTIVE SENSING

STATUS 11111110 (FEH)

Transmitted at every 200 msec.

Once this code is received, the instrument starts sensing. When no status nor data is received for over

approximately 350 ms, MIDI receiving buffer will be cleared, and the sounds currently played and the Sustain

Switch are forcibly turned off. Also, the values of the Controllers are reset to the default settings.

(3-6) SYSTEM EXCLUSIVE MESSAGE

(3-6-1) UNIVERSAL NON REALTIME MESSAGE

(3-6-1-1) IDENTITY REQUEST (Receive only)

F0H 7EH 0nH 06H 01H F7H

(“n” = Device No. However, this instrument receives under “omni.”)

(3-6-1-2) IDENTITY REPLY (Transmit only)

F0H 7EH 7FH 06H 02H 43H 00H 41H ddH 06H 00H 00H 00H 7FH F7H

dd = CP4 STAGE: 49, CP40 STAGE: 4A

(3-6-2) PARAMETER CHANGE

(3-6-2-1) NATIVE PARAMETER CHANGE

11110000 F0 Exclusive Status

01000011 43 YAMAHA ID

0001nnnn 1n Device Number

01111111 7F Model ID

0******* ** Model ID CP4 STAGE: 1A, CP40 STAGE: 1B

0aaaaaaa aaaaaaa Address High

0aaaaaaa aaaaaaa Address Mid

0aaaaaaa aaaaaaa Address Low

0ddddddd ddddddd Data

11110111 F7 End of Exclusive

For parameters with data size of 2 or more, the appropriate number of data bytes will be transmitted.

See the following MIDI Data Table for Address.

(3-6-3) BULK DUMP

11110000 F0 Exclusive Status

01000011 43 YAMAHA ID

0000nnnn 0n Device Number

01111111 7F Model ID

0******* ** Model ID CP4 STAGE: 1A, CP40 STAGE: 1B

0bbbbbbb bbbbbbb Byte Count

0aaaaaaa aaaaaaa Address High

0aaaaaaa aaaaaaa Address Mid

0aaaaaaa aaaaaaa Address Low

0 0 Data

0ccccccc ccccccc Check-sum

11110111 F7 End of Exclusive

See the following BULK DUMP Table for Address and Byte Count.

The Check sum is the value that results in a value of 0 for the lower 7 bits when the Byte Count, Start Address,

Data and Check sum itself are added.

(3-6-4) DUMP REQUEST

11110000 F0 Exclusive Status

01000011 43 YAMAHA ID

0010nnnn 2n Device Number

01111111 7F Model ID

0******* ** Model ID CP4 STAGE: 1A, CP40 STAGE: 1B

0aaaaaaa aaaaaaa Address High

0aaaaaaa aaaaaaa Address Mid

0aaaaaaa aaaaaaa Address Low

11110111 F7 End of Exclusive

See the following DUMP REQUEST Table for Address and Byte Count.

(3-6-5) PARAMETER REQUEST

11110000 F0 Exclusive Status

01000011 43 YAMAHA ID

0011nnnn 3n Device Number

01111111 7F Model ID

0******* ** Model ID CP4 STAGE: 1A, CP40 STAGE: 1B

0aaaaaaa aaaaaaa Address High

0aaaaaaa aaaaaaa Address Mid

0aaaaaaa aaaaaaa Address Low

11110111 F7 End of Exclusive

See the following MIDI Data Table for Address.

(4) SYSTEM OVERVIEW (Keyboard and Tone Generator)

Although two types of note on/note off data, received via MIDI and played on the keyboard will be distinguished, the other

controllers (channel messages) equally affect the entire notes.

ALL SOUND OFF clears all the sounds in the specific channel(s) played by both the keyboard and the data via MIDI.

ALL NOTES OFF received via MIDI clears the sounds in the specific channel(s) played via MIDI.

KBD

MIDI In

MIDI Out

From USB

To USB

USB/MIDI = MIDI

Local Sw

KBD

Local Sw

Thru Port

USB/MIDI = USB

MIDI In

MIDI Out

From USB

To USB