User Manual

CP4 STAGE/CP40 STAGE Data List
17
Parameters marked with a dot () in the “Ctrl” column can be controlled from an FC1 (Foot Controller 1) etc.
Effect Parameter List
Reverb Block
•Rich Hall
•Rich Plate
•Rich Room
• Room 1
• Room 2
•Stage 1
•Stage 2
• Woody Room
*1 For details, refer to Effect Data Assign Table.
• NHall
• NRoom
•NPlate
Chorus/Insertion Block
In the Chorus Block, the Dry/Wet Balance and Mix parameters are not available.
For the effect types available for each block, refer to Effect Type List.
•Thru
When this type is selected, no parameters are available.
Category – DELAY
• Cross Delay
• Tempo Cross Delay
• Tempo Delay Mono
• Tempo Delay Stereo
•Delay L, R
No. Parameter Range Value Table No. C trl
1 Reverb Time 0.3s – 30.0s 0 – 69 4
2—
3—
4 HPF Cutoff Frequency 20Hz – 8.0kHz 0 – 52 3
5—
6—
7—
8—
9—
10 —
11 —
12 —
13 —
14 Feedback High Damp 0.1 – 1.0 1 – 10
15 —
16 —
No. Parameter Range Value Table No. C trl
1 Reverb Time 0.3s – xy.zs (*1) 0 – 69 26
2—
3—
4 HPF Cutoff Frequency 20Hz – 8.0kHz 0 – 52 3
5—
6—
7—
8—
9—
10 —
11 —
12 —
13 —
14 —
15 —
16 —
No. Parameter Range Value Table No. C trl
1 RevTime 0.3s – 30.0s 0 – 69 4
2 Plate Type Clear, Dark 0 – 2
3 Initial Delay 0.1ms – 200.0ms 0 – 127 5
4 High Damp 1.0kHz – 20.0kHz 34 – 60 3
5—
6 High Ratio 0.1 – 1.0 1 – 10
7—
8—
9—
10 —
11 —
12 —
13 EQ Low Frequency 22Hz – 1.0kHz 1 – 34 3
14 EQ Low Gain -12dB – 0dB – +12dB 52 – 76
15 EQ High Frequency 500Hz – 18.0kHz 28 – 59 3
16 EQ High Gain -12dB – 0dB – +12dB 52 – 76
No. Parameter Range Value Table No. C trl
1 Delay Time L>R 0.1ms – 1638.3ms 1 – 16383
2 Delay Time R>L 0.1ms – 1638.3ms 1 – 16383
3 Feedback Level -63 – +63 1 – 127
4 Input Select L, R, L&R 0 – 2
5 Feedback High Damp 0.1 – 1.0 1 – 10
6—
7—
8—
9—
10 Dry/Wet Balance D63>W – D=W – D<W63 1 – 127 
11 —
12 —
13 EQ Low Frequency 32Hz – 2.0kHz 4 – 40 3
14 EQ Low Gain -12dB – +12dB 52 – 76
15 EQ High Frequency 500Hz – 16.0kHz 28 – 58 3
16 EQ High Gain -12dB – +12dB 52 – 76
No. Parameter Range Value Table No. C trl
1 Delay Time L>R 32nd/3 – 4thx6 0 – 19 14
2 Delay Time R>L 32nd/3 – 4thx6 0 – 19 14
3 Feedback Level -63 – +63 1 – 127
4 Input Select L, R, L&R 0 – 2
5 Feedback High Damp 0.1 – 1.0 1 – 10
6 Lag -63ms – +63ms 1 – 127
7—
8—
9—
10 Dry/Wet Balance D63>W – D=W – D<W63 1 – 127 
11 —
12 —
13–16: Same as the parameters shaded in gray in Cross Delay above.
No. Parameter Range Value Table No. C trl
1 Delay Time 32nd/3 – 4thx6 0 – 19 14
2 Feedback Level -63 – +63 1 – 127
3 Feedback High Damp 0.1 – 1.0 1 – 10
4 L/R Diffusion -63ms – +63ms 1 – 127
5 Lag -63ms – +63ms 1 – 127
6—
7—
8—
9—
10 Dry/Wet Balance D63>W – D=W – D<W63 1 – 127 
11 —
12 —
13–16: Same as the parameters shaded in gray in Cross Delay above.
No. Parameter Range Value Table No. C trl
1 Delay Time L 0.1ms – 1638.3ms 1 – 16383
2 Delay Time R 0.1ms – 1638.3ms 1 – 16383
3 Feedback Time 1 0.1ms – 1638.3ms 1 – 16383
4 Feedback Time 2 0.1ms – 1638.3ms 1 – 16383
5 Feedback Level -63 – +63 1 – 127
6 Feedback High Damp 0.1 – 1.0 1 – 10
7—
8—
9—
10 Dry/Wet Balance D63>W – D=W – D<W63 1 – 127 
11 —
12 —
13–16: Same as the parameters shaded in gray in Cross Delay above.