User Manual

Quick GuideEditing a Program
Editing a Performance
65
Owner’s Manual
Editing a Performance by using the Knobs
The four knobs at the top left of the instrument are not only for tweaking the sound while you perform—you can also
use them to edit a Performance, either in the Performance Play mode or the Performance Edit mode.
● When the [PAN/SEND] indicator is turned on:
● When the [TONE] indicator is turned on:
n The settings above are applied as offsets to the AEG and FEG settings in the Performance Edit mode.
● When the [ARP FX] indicator is turned on:
● When the [EQ] indicator is turned on:
n The settings above are applied as offsets to the EQ settings in the [PERFORM] → Performance selection → [EDIT] → [COMMON] → [F2]
OUT/MEF → [SF2] MEQ (Master EQ) display.
● When both the [PAN/SEND] and [TONE] indicators are turned on (by pressing them simultaneously):
n In addition to above functions, Master Effect related parameters (set in the [PERFORM] → Performance selection → [COMMON] → [F2] OUT/
MEF → [SF3] MEF display) can be assigned to these four knobs by pressing the [ARP FX] and [EQ] buttons simultaneously. The particular
parameters are assigned to the four knobs can be set in the [UTILITY] → [F4] CTL ASN → [SF5] MEF display.
Editing a Performance by using the Control sliders
In the Performance mode, the four Control sliders let you independently adjust the levels of the Parts (Voices), letting you control the
overall balance of the Parts.
n Inadvertent use of the sliders may result in no sound. If this occurs, move the sliders upward.
PAN Determines the stereo pan position of the Performance. [PERFORM] → Performance selection → [EDIT] → [COMMON]
→ [F2] OUT/MEF → [SF1] OUT → Pan
Page 172
REVERB Determines the amount of Reverb effect that is applied to the
Performance.
[PERFORM] → Performance selection → [EDIT] → [COMMON]
→ [F2] OUT/MEF → [SF1] OUT → RevSend
Page 172
CHORUS Determines the amount of Chorus effect that is applied to the
Performance.
[PERFORM] → Performance selection → [EDIT] → [COMMON]
→ [F2] OUT/MEF → [SF1] OUT → ChoSend
Page 172
TEMPO Determines the tempo of the Arpeggio assigned to the currently
selected Performance.
[PERFORM] → Performance selection → [F6] ARP → Tempo Page 171
CUTOFF Raises or lowers the Filter cutoff frequency to adjust the tone
brilliance.
[PERFORM] → Performance selection → [F5] EG → CUTOF Page 171
RESONANCE Boosts or attenuates the level at the area around the Filter cutoff
frequency.
[PERFORM] → Performance selection → [F5] EG → RESO Page 171
ATTACK Determines the attack time of the sound. For example, you can
adjust a strings Voice so that the sound gradually swells in volume
by setting a slow attack time – simply turn this knob to the right.
[PERFORM] → Performance selection → [F5] EG → ATK (AEG) Page 171
RELEASE
Determines the release time of the sound. Turning the knob to the right
sets a long release time and (depending on the Voice assigned to the
selected Performance) lets the sound sustain after the key is released. To
produce a sharp release, in which the sound abruptly cuts off, set a short
release time.
[PERFORM] → Performance selection → [F5] EG → REL (AEG) Page 171
SWING Adjusts the swing feel of the Arpeggio playback. [PERFORM] → Performance selection → [EDIT] → [COMMON]
→ [F3] ARP → [SF3] PLAY FX → Swing
Page 173
GATE TIME Adjusts the Gate Time (length) of the Arpeggio notes. [PERFORM] → Performance selection → [EDIT] → [COMMON]
→ [F3] ARP → [SF3] PLAY FX → GateTimeRate
Page 173
VELOCITY Adjusts the velocity of the Arpeggio notes. [PERFORM] → Performance selection → [EDIT] → [COMMON]
→ [F3] ARP → [SF3] PLAY FX → VelocityRate
Page 173
UNITMULTIPLY
Adjusts the Arpeggio playback time based on tempo. [PERFORM] → Performance selection → [EDIT] → [COMMON]
→ [F3] ARP → [SF3] PLAY FX → UnitMultiply
Page 173
LO Determines the amount of boost or attenuation applied to the low
frequency band of the Master EQ.
[PERFORM] → Performance selection → [EDIT] → [COMMON]
→ [F1] GENERAL → [SF3] MEQ OFS → LOW
Page 172
LO MID Determines the amount of boost or attenuation applied to the low-
midrange frequency band of the Master EQ.
[PERFORM] → Performance selection → [EDIT] → [COMMON]
→ [F1] GENERAL → [SF3] MEQ OFS → LOW MID
Page 173
HI MID Determines the amount of boost or attenuation applied to the high-
midrange frequency band of the Master EQ.
[PERFORM] → Performance selection → [EDIT] → [COMMON]
→ [F1] GENERAL → [SF3] MEQ OFS → HIGH MID
Page 173
HI Determines the amount of boost or attenuation applied to the high
frequency band of the Master EQ.
[PERFORM] → Performance selection → [EDIT] → [COMMON]
→ [F1] GENERAL → [SF3] MEQ OFS → HIGH
Page 173
ASSIGN A Adjusts parameters assigned to these knobs in the [UTILITY] → [F4] CTL ASN → [SF2] ASSIGN display. Page 71
ASSIGN B
ASSIGN 1 Depends on the settings of the Voice assigned to the selected Performance. Page 70
ASSIGN 2
[PERFORM] ➞ Performance selection ➞ [EDIT] ➞ Part selection ➞ [F2] OUTPUT ➞ [SF1] VOL/PAN ➞ Volume
TIP
TIP