Studio Manager for Owner’s Manual E
Important Information Special Notices • • • • • • • The software and this owner’s manual are the exclusive copyrights of Yamaha Corporation. Copying of the software or reproduction of this manual in whole or in part by any means is expressly forbidden without the written consent of the manufacturer. Yamaha makes no representations or warranties with regard to the use of the software and documentation and cannot be held responsible for the results of the use of this manual and the software.
Contents 1 Getting Started . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Starting Studio Manager . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Quitting Studio Manager . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Specifying the MIDI Port (Windows only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Configuring Studio Manager . . . . . . . . . . . . . . . . . . . . . . . . . .
Chapter 1—Getting Started 1 Getting Started Starting Studio Manager Windows: Click the Start button and then click Programs–>YAMAHA OPT Tools–>YAMAHA Studio Manager for 01V96–>Studio Manager for 01V96. Macintosh: Open the Studio Manager for 01V96 folder and double-click “SM_01V96.” If a 01V96 is detected while Studio Manager starts up, the Synchronization dialog box appears, from which you can choose to transfer the settings of the 01V96 to Studio Manager or vice versa.
Configuring Studio Manager 5 Configuring Studio Manager Selecting Ports In order to use Studio Manager, you must specify the input and output ports that Studio Manager should use to communicate with the 01V96. Windows: Choose System Setup from the File menu, and specify the input and output ports on the Setup dialog box, as shown below.
Chapter 1—Getting Started This is the Macintosh Setup window Input Port/Output Port: (Windows only) These pop-up menus are used to select the ports with which Studio Manager communicates with the 01V96. Console Device ID: Studio Manager can control any one of up to eight 01V96s, each with its own exclusive ID. Select the ID of the 01V96 that you want to control. Channel Select: These options determine whether or not channel selection is linked.
Working with Sessions 7 Working with Sessions • • • A Studio Manager Session consists of all 01V96 mix settings, including Scene and library data. To create a new Session, choose New Session from the File menu. To open a previously saved Session, choose Open Session from the File menu. To save the current Session, choose Save Session from the File menu. • To save the current Session with a new name, choose Save Session as from the File menu.
Chapter 2—Console Window 2 Console Window Studio Manager’s Console window displays 20 channel strips and a master section. When an Input Channel Layer is selected, 16 Input Channels and four Stereo Input channels are displayed. When the Master Layer is selected, the Bus Out, Aux Send and four Stereo Input channels channels are displayed. And when the Remote layer is selected, 16 Remote Channels and four Stereo Input channels are displayed.
Input Channels 9 Input Channels 1 B C D 5 6 7 8 9 J K L M N O P Q R This parameter is used to select an Input source. To select an Input source, click the parameter and choose from the list that appears. B Routing buttons These buttons are used to route the Input Channel to the Bus Outs. C STEREO button This button is used to route the Input Channel’s signal to the Stereo Out. D DIRECT button This button turns on and off the Input Channel’s routing to its Direct Out.
Chapter 2—Console Window P Delay parameter This parameter is used to set the delay time of the Delay function. Delay times can be set by dragging. Q Channel number This is the channel number. R AUX section These controls are used to set the levels of the Aux Sends. To set an Aux Send level, drag its bar or click a point along the length of the bar. To turn an Aux Send on or off, click its number.
Stero Input Channel 11 Stero Input Channel 1 B C 4 A SOURCE parameter This parameter is used to select an Input source. To select an Input source, click the parameter and choose from the list that appears. B Routing buttons These buttons are used to route the Input Channel to the Bus Outs. C STEREO button This button is used to route the Input Channel’s signal to the Stereo Out. D PHASE button This button is used to reverse the signal phase of the channel.
Chapter 2—Console Window O Short channel name This is the channel’s short name. To edit the name, click it and type. P Channel fader This is the Input Channel’s fader. Q Channel meter This meter displays the signal level of the channel L or R. Master Section 1 A ONLINE/OFFLINE status indicator This indicator shows whether Studio Manager is online or offline.
Output Channels 13 Output Channels When the Master Layer is selected, the Bus Out and Aux Send channels are displayed. A Bus Out channel is shown here. Aux Send channels appear the same except that they do not have a STEREO button. A STEREO button (Bus Out only) This button is used to route the Bus Out to the Stereo Out. B INSERT button 1 This button is used to turn on and off the Bus Out’s Insert. C COMP button This button is used to turn on and off the Bus Out’s Compressor.
Chapter 2—Console Window Remote Channels When the Remote Layer is selected, Remote Channels are displayed. A Channel number This is the channel number. B SELECT button This button is used to select the Remote Channel. C ON button This button turns the Remote Channel on and off. It appears orange while the channel is on. D Short channel name This is the Remote Channel’s short name. To edit the name, click it and type. E Channel fader This is the Remote Channel’s fader.
Selected Channel Window 15 3 Selected Channel Window • • • • • • The Selected Channel window allows detailed editing of the currently selected channel. To open the Selected Channel window, choose Selected Channel from the Windows menu. The layout of the Selected Channel window depends on the currently selected channel.
Chapter 3—Selected Channel Window B GATE section This section contains the Gate controls and display graph for the currently selected Input Channel. The rotary controls are used to set the threshold, range, attack, decay, and hold. The GR meter indicates the amount of gain reduction being applied by the Gate. The ON button turns the Gate on and off. The LINK button links the Gate of the currently selected Input Channel with the Gate of its partner channel.
Stereo Input Channels 17 I PAIR, FADER GROUP & MUTE GROUP section This section contains the Pair, Fader and Mute group functions for the currently selected Input Channel. Click the heart icon to pair and unpair the channel with its partner channel. Use the FADER GROUP buttons to add the channel to Fader groups, and use the MUTE GROUP buttons to add it to Mute groups. Stereo Input Channels This is the Selected Channel window for Input Channels.
Chapter 3—Selected Channel Window D Routing, pan & level section This section contains the routing, pan, and level controls and the, SOLO, and ON buttons for the currently selected Stereo Input Channel. ROUTING buttons 1–8 are used to route the channel to the Bus Outs. The STEREO button routes the channel to the Stereo Out. The DIRECT button routes the channel to its Direct Out, and the Direct Out parameter below it selects a Direct Out destination. The F.
Bus Outs 19 A CHANNEL SELECT section Channels can be selected by clicking the Channel ID and selecting from the list that appears, or by clicking the left and right Channel Select buttons. The long channel name is displayed below the Channel ID. The LIBRARY button opens the Channel Library window. B EQUALIZER section This section contains the EQ controls and display graph for the currently selected Bus Out. It’s layout is identical to the EQUALIZER section for Input Channels.
Chapter 3—Selected Channel Window Aux Sends This is the Selected Channel window for Aux Sends. 2 1 5 6 3 4 7 A CHANNEL SELECT section Channels can be selected by clicking the Channel ID and choosing from the list that appears, or by clicking the left and right Channel Select buttons. The long channel name is displayed below the Channel ID. The LIBRARY button opens the Channel Library window.
Stereo Out 21 F INSERT section This section contains the Insert parameters for the currently selected Aux Send. The INSERT button turns the Insert on and off. The OUT and IN parameters are used to specify the insert out destination and insert in source respectively. The POSITION parameter is used to specify the position of the Insert in the signal path. G PAIR, FADER GROUP & MUTE GROUP section This section contains the Pair, Fader and Mute group functions for the currently selected Aux Send.
Chapter 3—Selected Channel Window C DELAY section This section contains the delay controls for the Stereo Out. The rotary control is used to set the delay time, and the ON button turns the Delay function on and off. D Balance & level section This section contains the balance control and ON buttons, and channel fader for the Stereo Out. E COMPRESSOR section This section contains the Compressor controls and display graph for the currently selected Stereo Out.
Library Window 4 Library Window The Library window allows you to control and manage 01V96 Scenes and libraries. In addition, Scenes and libraries can be saved to disk on your computer.
Chapter 4—Library Window D SAVE button This button is used to save the currently open Library file. E SAVE AS button This button is used to save the currently open Library file with a different name. F TITLE pane This pane displays the memory list. G PROTECT pane This pane displays a padlock icon for protected memories. H INPUT PATCH LINK pane This pane displays the number of the linked input patch memory. I OUTPUT PATCH LINK pane This pane displays the number of the linked output patch memory.
Patch Editor Window 25 5 Patch Editor Window The Patch Editor window is used to patch Inputs, Outputs, Inserts, Effects, and Direct Outs. It consists of five pages, which are selected by clicking the tabs along the top of the window. To open the Patch Editor window, choose Patch Editor from the Windows menu. INPUT PATCH Page 1 2 3 4 5 6 A Channel IDs These are the Channel IDs. B Long channel names These are the Channel long names. To edit a name, click it and type.
Chapter 5—Patch Editor Window OUTPUT PATCH Page 1 2 3 4 5 6 A Channel IDs These are the Channel IDs. B Long channel names These are the Channel long names. To edit a name, click it and type. C AUTO SETUP button Clicking this button sets the patches on this page to their initial values. D ALL CLEAR button This button clears all patches on this page. E LIBRARY button This button opens the Output Patch Library window. F Patchbay The patchbay is used to patch output ports to Output Channels.
INSERT PATCH Page 27 INSERT PATCH Page 1 3 2 5 4 A Channel IDs These are the Channel IDs. B Long channel names These are the Channel long names. To edit a name, click it and type. C LIBRARY buttons These buttons open the Input and Output Patch Library windows. D Insert Out Patchbay This patchbay is used to patch output ports to the Insert Outs of Input Channels, Bus Outs, Aux Sends, and the Stereo Out. Active patches are indicated by a red dot. To make a patch, click a square.
Chapter 5—Patch Editor Window EFFECT PATCH Page 1 2 A Effects processor #1—#4 inputs These parameters are used to select input sources for internal effects processors #1—#4. B LIBRARY button This button opens the Input Patch Library window.
DIRECT OUT Patch Page 29 DIRECT OUT Patch Page 1 2 3 4 A Channel IDs These are the Channel IDs. B Long channel names These are the Channel long names. To edit a name, click it and type. C LIBRARY button This button opens the Output Patch Library window. D Patchbay The patchbay is used to patch output ports to the Direct Outs. Active patches are indicated by a red dot. To make a patch, click a square. To unpatch, click a red dot.
Chapter 6—Surround Editor Window 6 Surround Editor Window The Surround Editor window allows you to edit the surround pan position of the currently selected Input Channel. To open the Surround Editor window, choose Surround Editor from the Windows menu. 1 3 2 5 4 6 87 A CHANNEL SELECT section Channels can be selected by clicking the Channel ID and selecting from the list that appears, or by clicking the left and right Channel Select buttons.
Effect Editor Window 31 7 Effect Editor Window The Effect Editor window allows you to edit the internal effects processors. To open the Effect Editor window, choose Effect Editor from the Windows menu. 1 6 3 4 5 2 7 8 A Effects processor select These buttons are used to select the internal effects processors. B Effect select section The EFFECT NAME, TYPE, and IN/OUT are the name, type and I/O configuration of the effect recalled to the currently selected effects processor.
Chapter 8—Keyboard Shortcuts 8 Keyboard Shortcuts File Menu Windows CTRL+N Macintosh Action -N Creates a new Session CTRL+O -O Opens a previously saved Session CTRL+S -S Saves the current Session Windows Menu Windows Macintosh Action CTRL+W -W Closes the foremost window except the Console window CTRL+ALT+W -Option-W Closes all windows except the Console window CTRL+1 -1 Opens the Selected Channel window CTRL+2 -2 Opens the Library window CTRL+3 -3 Opens the Patch Editor wind
Index Numerics 01V96 INTERNAL DATA pane 24 A ALL CLEAR button 25, 26 All Lib, synchronization 6 AUTO SETUP button 25, 26 AUX section 10, 11 Aux Send masters selected channel window 20 AUX SEND section 16, 18 B BAL control 22 Bus Outs console window 13 selected channel window 18 BYPASS button 31 C Channel 10 Channel fader 10, 12, 13, 14, 16, 18, 19 Channel IDs 25, 26, 27, 29 Channel library 23 Channel meter 10, 12, 13 Channel number 10, 11, 13, 14 CHANNEL SELECT section 15, 17, 19, 20, 21, 22, 30 Chan
K Keyboard shortcuts 32 L Launching Studio Manager 4 LAYER buttons 12 Layer Select, preference 6 LFE control 10, 11, 30 LIBRARY button 15, 16, 17, 19, 20, 21, 25, 26, 27, 28, 29, 31 Library window 23 LINK button (6.
Y Yamaha Web Site 2 Studio Manager for 01V96—Owner’s Manual
Yamaha Manual Library http://www2.yamaha.co.jp/manual/english/ M.D.G.
