Owner's Manual

PRECAUTIONS
PLEASE
READ
CAREFULLY
BEFORE
PROCEEDING
*
Please keep this manual
in
a safe place for future reference.
it
WARNING
Always
follow
the
ba+sic
precautions
listed
below
to
avoid
the
possibility
of
serious
injury
or
even
death
from
electrical
shock,
short-circuiting,
damages,
fire
or
other
hazards.
These
precautions
include,
but
are
not
limited
to,
the
following:
Do
not
open
•
This
device
contains
no
user-serviceable
parts.
Do
not
open
the
device
or
attempt
to
disassemble
the
internal
parts
or
modify
them
in
any
way
.
If
it
should
appear
to
be
malfunctioning
,
discontinue
use
immediately
and
have
it
inspected
by
qualified
Yamaha
service
personnel.
it
CAUTION
Always
follow
the
basic
precautions
listed
below
to
avoid
the
possibility
of
physical
injury
to
you
or
others,
or
damage
to
the
device
or
other
property.
These
precautions
include,
but
are
not
limited
to,
the
following:
Location
•
Do
not
place
the
device
in
a
location
where
it
may
come
into
contact
with
corrosive
gases
or
salt
air.
Doing
so
may
result
in
malfunction.
•
Before
moving
the
device,
remove
all
connected
cables
.
•
Always
consult
qualified
Yamaha
service
personnel
if
the
device
installation
requires
construction
work,
and
make
sure
to
observe
the
following
precautions
.
-
Avoid
locations
that
are
exposed
to
constant
vibration.
-
Use
the
required
tools
to
install
the
device
.
-
Inspect
the
device
periodically.
Handling
caution
•
Avoid
inserting
or
dropping
foreign
objects
(paper,
plastic,
metal,
etc.)
into
any
gaps
or
openings
on
the
device
.
If
this
happens,
have
the
device
inspected
by
qualified
Yamaha
service
personnel.
•
Do
not
rest
your
weight
on
the
device
or
place
heavy
objects
on
it,
and
avoid
use
excessive
force
on
the
buttons,
switches
or
connectors.
Yamaha
cannot
be
held
responsible
for
damage
caused
by
improper
use
or
modifications
to
the
device,
or
data
that
is
lost
or
destroyed.
Error Messages
LED Status
Meaning
NOTICE
To
avoid the possibility of malfunction/ damage to the
product, damage
to
data, or damage to other property,
follow the notices below.
•
Handling and Maintenance
•
Do
not use the device
in
the vicinity of a
TV,
radio,
stereo equipment, mobile phone, or other electric
devices. Otherwise, the device,
TV,
or radio
may
generate noise.
•
Do not expose the device
to
excessive dust or
vibration, or extreme cold or heat (such
as
in
direct
sunlight, near a heater, or
in
a car during the day),
in
order
to
prevent the possibility of panel disfiguration,
unstable operation, or damage
to
the internal
components.
•
Do
not place vinyl, plastic or rubber objects
on
the
device, since this might discolor the
panel.
• When cleaning the device, use a dry and soft cloth.
Do
not use paint thinners, solvents,
cleaning fluids, or
chemical-impregnated wiping
cloths.
•
About this manual
• The
illustrations
as shown
in
this manual are for
instructional purposes
only,
and may appear
somewhat different from those
on
your device.
• The company names and product names
in
this
manual are the trademarks or registered trademarks of
their respective companies.
Action ,
All
LEOs
are flashing Cannot start up properly
The control panel may have malfunctioned. Contact your Yamaha
quickly.
because of some problem with dealer.
the hardware.
The two
LEOs
are
The voltage supply
is
Use
CAT5e
or higher Ethernet straight cable that has
all
eight pins
flashing alternately.
insufficient due
to
low power connected. Also make sure
to
connect so that the
total
length of
supply from the connected
cables between the connected host device and the terminated
host device.
control panel
is
no longer than
200
meters.
Each
LED
lights
in
A malfunction has occurred
•If
the device
is
connected
to
an MTX, certain Panel
IDs
may be
sequence. with communication with the duplicated. Make sure that each control Panel connected
to
the
host device. same MTX has a unique
PaneiiD.
•
Make sure that the termination switch
is
set
to
ON
to
terminate the
last control panel
in
a daisy chain connection.
•
The cables may have been broken or there
is
some other cable
connection failure. Use the proper cables.