User Manual

Troubleshooting
51
• Is the GATE/COMP set to an extreme threshold or
ratio? (“CS1D Reference Manual (Hardware)”
→p.25, 27)
• Is the EQ attenuator raised?
(“CS1D Reference Manual (Hardware)” →p.29)
• Is the output channel [LEVEL] encoder raised?
(“CS1D Reference Manual (Hardware)” →p.63)
• Check the levels in the METER screen.
(“CS1D Reference Manual (Software)” →p.58)
• Is the [GAIN] switch (maximum output setting) of
the analog output card set to the correct position?
→refer to the manual included with the I/O cards.
• Has the DCA fader to which that channel is assigned
been raised? (“CS1D Operation Manual (Basic Oper-
ation)” →p.93)
■ Sound is distorted
• Is the word clock set correctly?
(“CS1D Operation Manual (Start-up)” →p.24, 28,
“CS1D Reference Manual (Software)” →p.53)
• Are the head amp and [GAIN] encoder set correctly?
(“CS1D Reference Manual (Hardware)” →p.21, 31)
• Is the input channel fader raised excessively? (“CS1D
Reference Manual (Hardware)” →p.32)
• Is the STEREO A/B channel fader raised excessively?
(“CS1D Reference Manual (Hardware)” →p.53)
• Is the EQ gain raised excessively? (“CS1D Reference
Manual (Hardware)” →p.29)
• Is the analog output card [GAIN] switch (maximum
output setting) set to the correct position? →refer to
the manual included woth the I/O cards.
■ Sound is output even though not patched to
an output channel
• Is the signal set to DIRECT OUT? (“CS1D Operation
Manual (Basic Operation)” →p.91)
• Is the signal set to INSERT OUT? (“CS1D Operation
Manual (Basic Operation)” →p.85)
■ No response when the MIX SEND encoder is
rotated
• Is the MIX bus set to FIX MODE?
(“CS1D Reference Manual (Software)” →p.155)
• Is MIX SEND turned on? (“CS1D Reference Manual
(Hardware)” →p.23)
• In the case of the send point is set to POST, has the
fader been lowered? (“CS1D Reference Manual
(Hardware)” →p.23, “CS1D Reference Manual (Soft-
ware)” →p.158)
■ A paired channel does not sound like stereo
• Is the pan mode setting and the pan value correct?
(“CS1D Reference Manual (Hardware)” →p.30,
“CS1D Reference Manual (Software)” →p.158)
■ The volume of a specific channel rises and
falls
• Is ducking specified for GATE/COMP? (“CS1D
Operation Manual (Basic Operation)” →p.55)
■ Cannot save a scene memory or library data
• Are you attempting to save over read-only memory
number or number that has been memory protected?
(“CS1D Reference Manual (Software)” →p.18, 166)
• In TC EVENT, the EVENT RECALLING parameter
may have been set to ENABLE. (“CS1D Reference
Manual (Software)” →p.33)
■ Can’t save to memory card
• Is the memory card protected?
• Does the memory card contain sufficient space for
saving the data?
■ Can’t load from memory card
• TC EVENT IN may have been set to ENABLE.
■ Cannot transmit/receive MIDI data
• Does the MIDI PORT selection match the connec-
tions?
(“CS1D Reference Manual (Software)” →p.29)
• Are the MIDI MODE and channel settings made cor-
rectly for the transmitting and receiving devices?
(“CS1D Reference Manual (Software)” →p.29)
• Has an event been specified for the program change?
(“CS1D Reference Manual (Software)” →p.29)
■ Operating the faders does not produce the
desired level adjustment
• Are the [LAYER] or [FLIP] switches set to the appro-
priate fader mode or mixing layer? (“CS1D Reference
Manual (Hardware)” →p.5, 13)
■ Only a specific channel is heard from the
MONITOR or PHONES jack
• Is CUE turned ON? (“CS1D Operation Manual
(Basic Operation)” →p.116)
■ Noise is heard on a connected external
device (recorder, etc.)
• Is the word clock setting correct? (“CS1D Operation
Manual (Start-up)” →p.24, 28, “CS1D Reference
Manual (Software)” →p.53)
• Is an unsynchronized signal being input? (“CS1D
Reference Manual (Software)” →p.55)
• Is the Dither setting appropriate? (“CS1D Reference
Manual (Software)” →p.56)
• Is the OSCILLATOR, TALKBACK, or SUB IN oper-
ating? (“CS1D Operation Manual (Basic Opera-
tion)” →p.120)