Installation Sheet

ManualsBrandsYale ManualsDeadboltsYale Single Cylinder Keyed Entry Deadbolt with C Keyway and Round Rose from the Edge Series

P/N - Rev AYE DBINSTL

Yale Edge Series

Single and Double Cylinder Deadlocks

Installation Instructions

For use on doors 1-3/8" to 1-3/4" (35mm - 45mm)

Backset is distance from door edge to center of hole on door face.

Select Proper Backset

Latch Tail

Notch

Latch Faceplate

Backset

2-3/8" or 2-3/4"

(60mm - 70mm)

To adjust backset from 2-3/8" to 2-3/4"

To adjust backset from 2-3/4" to 2-3/8"

Retract latchbolt. Hold latch tail and

rotate faceplate

clockwise.

Once notch is in

groove, push latch

faceplate towards

latch tail.

Rotate latch faceplate

counter clockwise and

check that notch is at

2-3/8" mark.

Retract latchbolt. Hold latch tail and

rotate faceplate

clockwise.

Once notch is in

groove, pull latch

faceplate away

from latch tail.

Rotate latch faceplate

counter clockwise and

check that notch is at

2-3/4" mark.

Template

NOTE:

TEMPLATE MUST

BE PLACED ON

HIGH EDGE OF

DOOR BEVEL

MARK

DRILL

2-1/8" (54mm)

HOLE

FOLD HERE

1-3/4" (45mm)

THICK DOOR

1-3/8" (35mm)

THICK DOOR

MARK

PROPER

DOOR

THICKNESS

DRILL 1" (25mm)

HOLE IN EDGE OF DOOR

2" (51mm) DEEP

CAUTION:

If printed from

website print 1:1

scale. Measure

dimensions for

accuracy before use.

2-3/8" (60mm) BACKSET

2-3/4" (70mm) BACKSET

Summary of content (4 pages)

PAGE 1
Yale Edge Series Single and Double Cylinder Deadlocks Installation Instructions ® Select Proper Backset For use on doors 1-3/8" to 1-3/4" (35mm - 45mm) Backset is distance from door edge to center of hole on door face. Latch Faceplate Latch Tail Backset 2-3/8" or 2-3/4" (60mm - 70mm) To adjust backset from 2-3/8" to 2-3/4" Retract latchbolt. Hold latch tail and Once notch is in rotate faceplate groove, pull latch clockwise. faceplate away from latch tail.
PAGE 2
1 Mark Door Fold and apply template to high edge of door bevel and mark center of door edge as indicated on template at desired height from floor. Mark center hole on door face through guide on template for either 2-3/8" (60mm) or 2-3/4" (70mm) backset. 2 Drill Holes Drill through door face as marked for deadlock. Note: Drill holes from both sides to prevent splitting. Hole size is 2-1/8" (54mm) for standard installations.
PAGE 3
Install Deadbolt Latch Insert deadbolt latch in hole keeping it parallel to face of door and in UP position as indicated on latch. Mark outline and remove latch. Chisel 1/8" (3.2mm) deep or until latch face is flush with door edge. Insert deadbolt latch in hole keeping it parallel to face of door and in UP position as indicated on latch.. Mark two (2) fastener holes, remove latch and drill pilot holes with 1/16" (1.6mm) drill bit.
PAGE 4
5 Install Exterior Cylinder Press cylinder flush against door making certain the torque blade is properly positioned in latch crank. Tapped holes in mounting plate of exterior cylinder should be aligned with latch holes. Key hole should be in down position. Torque blade inserted horizontally into latch crank. Key hole in down position. 6 Install Interior Mechanism Slide interior turn piece onto exterior cylinder torque blade. Insert machine screws through holes engaging holes in cylinder and tighten.