UNO-2053E GX2-400 Universal Network Controller with PC Card, 2xLAN, 2xUSB, 2xRS-232, Audio User Manual
Copyright Notice The documentation and the software included with this product are copyrighted 2006 by Advantech Co., Ltd. All rights are reserved. Advantech Co., Ltd. reserves the right to make improvements in the products described in this manual at any time without notice. No part of this manual may be reproduced, copied, translated or transmitted in any form or by any means without the prior written permission of Advantech Co., Ltd.
Product Warranty (2 years) Advantech warrants to you, the original purchaser, that each of its products will be free from defects in materials and workmanship for two years from the date of purchase. This warranty does not apply to any products which have been repaired or altered by persons other than repair personnel authorized by Advantech, or which have been subject to misuse, abuse, accident or improper installation.
CE This product has passed the CE test for environmental specifications when shielded cables are used for external wiring. We recommend the use of shielded cables. This kind of cable is available from Advantech. FCC Class A This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
Contents Chapter Chapter Chapter 1 UNO-2053E Overview .................................... 2 1.1 1.2 1.3 1.4 Introduction ....................................................................... 2 Hardware Specifications ................................................... 2 Safety Precautions ............................................................. 4 UNO-2053E Series............................................................ 5 1.5 Chassis Dimensions................................................
A.7 VGA Display Connector (VGA1)................................... 18 A.8 A.9 CompactFlash Master/Slave Jumper Setting (JP2) ......... 19 Enhanced IDE Connector (CN2) .................................... 20 UNO-2053E User Manual Table A.8:VGA Adaptor Cable Pin Assignments ....... 18 Table A.9:IDE Hard Drive Connector Pin Assigns .....
CHAPTER 1 UNO-2053E Overview This chapter gives background information on the UNO-2053E. It shows you the UNO-2053E overview and specifications.
Chapter 1 UNO-2053E Overview 1.1 Introduction Are you looking forward to a suitable embedded Application Ready Platform (ARP) that could shorten your development time and offer rich networking interfaces to fulfill your extensive needs in different kind of projects? Advantech Universal Network Controller (UNO-2000 series) is your ANSWER concentrating the services on Network-enabled Application Ready Platform total solution.
• Serial Port: Two standard RS-232 ports - IRQ: All ports use the same IRQ assigned by BIOS - Data bits: 5, 6, 7, 8 - Stop bits: 1, 1.5, 2 - Parity: none, even, odd - Speed: 50~115.2 kbps - Data signals: TxD, RxD, RTS, CTS, DTR, DSR, DCD, RI, GND - Max data distance: 50 feet (15.2 meters) • USB interface: USB OpenHCI, Rev. 1.0 compliant USB specification version 1.
1.3 Safety Precautions The following sections tell how to make each connection. In most cases, you will simply need to connect a standard cable. All of the connector pin assignments are shown in Appendix A. Warning!! Always disconnect the power cord from your chassis when you are working on it. Do not connect while the power is on. A sudden rush of power can damage sensitive electronic components. Only experienced electronics personnel should open the chassis.
1.4 UNO-2053E Series There are two products in UNO-2053E series listed as below: • UNO-2053E: UNO-2053E hardware platform • UNO-2053ECE: UNO-2053E hardware platform with WinCE OS (built in 128MB CompactFlash card) • UNO-2053EXP: UNO-2053E hardware platform with WinXPe OS (built in 1GB CompactFlash card) 1.4.
1.5 Chassis Dimensions Figure 1.
CHAPTER 2 Hardware Functionality This chapter shows how to set up the UNO-2053E’s hardware functions, including connecting peripherals, switches and indicators.
Chapter 2 Hardware Functionality 2.1 UNO-2053E Peripherals The following two figures show the connectors on UNO-2053E. The following sections give you detail information about function of each peripheral. Figure 2.1: UNO-2053E Front Panel Figure 2.2: UNO-2053E Rear Panel 2.2 COM1~COM2: RS-232 Interfaces The UNO-2053E offers two standard RS-232 serial communication interface ports on COM1 and COM2. Please refer to A.2 for pin assignments. 2.
2.4 Power Connector The UNO-2053E comes with a Phoenix connector that carries 10~30 VDC external power input, and has reversed wiring protection. Therefore, it will not cause any damage to the system by reversed wiring of ground line and power line. Please refer to A.4 for its pin assignments. 2.5 LED Indicators There are two LEDs on the UNO-2053E front panel for indicating system status: PWR LED is for power status and IDE LED is for IDE bus status. 2.
2.9 VGA: VGA Display Connector The UNO-2053E provides a VGA controller for a high resolution VGA interface. It supports VGA and VESA, up to 1280 x 1024 @ 256 color and 1024 x 768 @ 24bpp resolution and up to 16 MB share memory. The VGA interface is reserved for system testing and debugging. 2.10 RESET: Reset Button Pressing the “RESET” button will reset UNO-2053E. 2.11 Audio UNO-2053E supports audio function with - Microphone - Line In - Line Out.
CHAPTER 3 Initial Setup This chapter shows how to initial the UNO-2053E, sections include: Sections include: • Insert CompactFlash Card • Chassis grounding • Connect the Power • BIOS Setup and System Assignments
Chapter 3 Initial Setup 3.1 CompactFlash Card Installation The procedure for installing a CompactFlash card into the UNO-2053E is as follows, please follows these steps carefully. Step 1: Remove power cord. Step 2: Unscrew four screws from the rear panel of the UNO-2053E. Step 3: Remove the rear panel. Step 4: Plug a CompactFlash card with user’s OS and application program into a CompactFlash card slot on board. Step 5: Screw back the rear panel with four screws. 3.
APPENDIX A Pin Assignments This appendix shows the UNO-2053E pin assignments •Board Connectors and Jumpers •RS-232 Serial Port •Ethernet RJ-45 Connector •Phoenix Power Connector •PS/2 Keyboard and Mouse Connector •USB Connector •VGA Display Connector •CompactFlash Master/Slave Jumper Setting •Enhanced IDE connector
Appendix A Pin Assignments A.1 Board Connectors and Jumpers There are connectors and jumpers on the UNO-2053E board. The following sections tell you how to configure the UNO-2053E hardware setting. Figure A-1 and figure A-2 show the locations of UNO-2053E connectors and jumpers. Figure A.1: Connector & Jumper Locations (Top) Figure A.
Table A.
A.2 RS-232 Serial Port 9C (COM1~C0M2)(Male DB9) Table A.2: RS-232 Serial Port Pin Assignments 1 DCD 2 RxD 3 TxD 4 DTR 5 GND 6 DSR 7 RTS 8 CTS 9 RI A.3 Ethernet RJ-45 Connector (LAN1~LAN2) Table A.
A.4 Phoenix Power Connector (C) Table A.4: Phoenix Power Connector Pin Assigns Pin Signal Name 1 +10~30 VDC 2 GND A.5 PS/2 Keyboard and Mouse Connector (KM1) PS/2 KB/MS Connector Pin Assignments 6 5 3 4 2 1 Table A.5: Table A.
A.6 USB Connector (CON1, CON2) Table A.7: USB Connector Pin Assignments Pin Signal Name Cable Color 1 VCC Red 2 DATA- White 3 DATA+ Green 5 GND Black A.7 VGA Display Connector (VGA1) Table A.8: VGA Adaptor Cable Pin Assignments Pin Signal Name Pin Signal Name 1 RED 9 NC 2 GREEN 10 GND 3 BLUE 11 NC 4 NC 12 NC 5 GND 13 H-SYNC 6 GND 14 V-SYNC 7 GND 15 NC 8 GND Chipset The UNO-2053E uses a AMD CS5535 chipset for its SVGA controller.
A.8 CompactFlash Master/Slave Jumper Setting (JP2) The CompactFlash interface uses a primary IDE channel, which can be set as the master or slave device by changing the setting of JP2. Master Device: (Default) JP2 Slave Device JP2 UNO-2053E has one internal CompactFlash card slot which supports CompactFlash type I (3mm thick) and type II (5 mm thick) cards.
A.9 Enhanced IDE Connector (CN2) Table A.
