Safety data sheet

ManualsBrandsXYZPRINTING Manuals3D PrintingDa Vinci 1.0 Pro 3D printer incl. filament

Material Safety Data Sheet

Product Name : PLA Model

Company

Address

Information Phone No.

Emergency Phone No.

1.COMPANY IDENTIFICATION

XYZprinting, Inc.

No.147, Sec. 3, Beishen Rd., Shenkeng Dist., New Taipei City, Taiwan (R.O.C.)

886-2-7705 8001

2.HAZARD IDENTIFICATION

Emergency Overview

CAUTION! May cause eye/skin irritation. Burning produces obnoxious and toxic fumes. Avoid

contact with skin and eyes. Avoid formation of dust and aerosols

Appearance: Clear, translucent, opaque, pellets.

Color: Clear Translucent Opaque

Physical state: Solid

Odor: Sweet

Potential health effects:

Eye contact: Contact with eyes may cause irritation.

Skin contact: Substance may cause slight skin irritation.

Ingestion: Ingestion may cause gastrointestinal irritation, nausea, vomiting and diarrhoea.

Inhalation: Inhalation of dust may cause shortness of breath, tightness of the chest, a sore throat and cough.

Low hazard for usual industrial or commercial handling.

Target organ effects: There were no target organ effects noted following ingestion or dermal exposure in animal

studies.

Sensitization: Did not cause sensitisation on laboratory animals

Specific hazards: No information available

Flammability: Fine dust dispersed in air may ignite.

Environmental precautions: Not determined See Section 12 for more information.

NFPA rating:

Health: 1

Special:

Data not available

Flamm: 1

Not determined

Reactivity: 0

HMIS classification:

Health: 1 Flamm: 1

Personal Protective Equipment: Not determined

Reactivity: 0

3.COMPOSITION / INFORMATION ON INGREDIENTS

Chemical name

Weight %

OSHA Exposure Limits

ACGIH Exposure Limits

Polylactide resin

9051-89-2

>98

None

All ingredients in quantities > 1.0% (0.1% for carcinogens) that are potentially hazardous per OSHA definitions.

This material can generate Particulates Not Otherwise Classifiable (PNOC). The

Occupational Safety and Health Administration (OSHA) PEL/TWA for PNOC is 15

mg/m3 for total dust and 5 mg/m3 for the respirable fraction. The American Conference

of Governmental Industrial Hygienists (ACGIH) TLV/TWA for PNOC is 10 mg/m3 for

inhalable particulates and 3mg/m3 for respirable particulates.

Other Standards:

1/5

Summary of content (5 pages)

PAGE 1
/5 Material Safety Data Sheet Product Name : PLA Model 1.COMPANY IDENTIFICATION Company Address Information Phone No. Emergency Phone No. XYZprinting, Inc. No.147, Sec. 3, Beishen Rd., Shenkeng Dist., New Taipei City, Taiwan (R.O.C.) 886-2-7705 8001 886-2-7705 8001 2.HAZARD IDENTIFICATION Emergency Overview CAUTION! May cause eye/skin irritation. Burning produces obnoxious and toxic fumes. Avoid contact with skin and eyes.
PAGE 2
/5 4.FIRST AID MEASURES Eye contact: Rinse immediately with plenty of water, also under the eyelids, for at least 15 minutes. Call a physician immediately. Skin contact: Rinse immediately with plenty of water for at least 15 minutes. If skin irritation persists, call a physician. Cool skin rapidly with cold water after contact with hot polymer. Inhalation: Move to fresh air. Call a physician immediately. Ingestion: Drink water as a precaution. Never give anything by mouth to an unconscious person.
PAGE 3
/5 8. EXPOSURE CONTROLS / PERSONAL PROTECTION Engineering measures: Where reasonably practicable this should be achieved by the use of local exhaust ventilation and good general extraction. Provide appropriate exhaust ventilation at places where dust is formed. Control parameters: None PERSONAL PROTECTIVE EQUIPMENT: Safety glasses with side-shields. Goggles. Eye protection: Skin and body protection: Impervious clothing. Respiratory protection: Respirator must be worn if exposed to dust.
PAGE 4
/5 11.TOXICOLOGICAL INFORMATION Principle Routes of Exposure: Eye contact. Skin contact. Inhalation. Ingestion. Acute toxicity: There were no target organ effects noted following ingestion or dermal exposure in animal studies. Local effects: May cause eye/skin irritation. Product dust may be irritating to eyes, skin and respiratory system. Caused mild to moderate conjuctival irritation in eye irritation studies using rabbits.
PAGE 5
/5 15.REGULATORY INFORMATION (Not meant to be all inclusive--selected regulations represented) NOTICE: The information herein is presented in good faith and believed to be accurate. However, no warranty, express or implied is given. Regulatory requirements are subject to change and may differ from one location to another; it is the buyer's responsibility to ensure that its activities comply with federal, state or provincial, and local laws.