User Guide

ManualsBrandsXyron ManualsOther2500

AT400-300 Adhesive Application – High Tack

AT402-300 Adhesive Application – Low Tack

AT406-170 Adhesive Application – Repositionable

DL403-300 Two-Sided Lamination

SL403-300 One-Sided Lamination

LAT405-300 Combination Lamination/Adhesive Application - High Tack

LAT406-300 Combination Lamination/Adhesive Application - Low Tack

LAT409-170 Combination Lamination/Adhesive Application - Repositionable

Please follow the attached directions carefully.

The Xyron

™

2500 is an economical and easy to use document finishing system.

This versatile and non-electric system has been designed to laminate or apply

mounting adhesive to a variety of media. The same system is capable of laminating,

selectively applying adhesive or laminating and applying adhesive at the same time.

With the Xyron 2500, documents are easily laminated or can be transformed into

signs, stickers or labels instantly. The machine and supplies are compatible with all

types of computer-printed media including laser, inkjet, color and thermal in a wide

range of material sizes and thickness.

Supply rolls for 2500

Adhesive Application &

Laminating System

USER’S GUIDE

Adhesive Application and Laminating System

2500

1-800-793-3523

EDNord - Istedgade 37A - 9000 Aalborg - Telefon 9633 3500

Summary of content (10 pages)

PAGE 1
2500 Adhesive Application and Laminating System 1-800-793-3523 U S E R ’ S G U I D E Adhesive Application & Laminating System The Xyron™ 2500 is an economical and easy to use document finishing system. This versatile and non-electric system has been designed to laminate or apply mounting adhesive to a variety of media. The same system is capable of laminating, selectively applying adhesive or laminating and applying adhesive at the same time.
PAGE 2
Understanding the Xyron 2500’s Adhesive/Laminating System Parts and Functions Upper Idle Bar Lower Idle Bar Paddle Used to lock document in place Top Cover Removes to install/remove supplies Feed Tray Used to guide and align documents into the machine Crank Handle Used to advance documents and film thru machine Upper Supply Roll Rubber Rollers Cut Blade Used to trim output as it exits – the machine will cut when moved to either direction Slots for Supply Installation Upper Cut Bar Lower Cut Guide Lower
PAGE 3
Setting Up Remove the machine from the packaging and place on a level surface. Locate the crank handle and training video which are taped to the bottom inside of the machine. Install the crank handle by carefully threading clockwise (direction of the arrows) into the lower rubber roller. Cut the tie wraps holding the upper cut bar and lower guide together. Training Video The Xyron 2500 comes with an instructional video.
PAGE 4
Step 3: Step 4: Step 5: • On the bottom • Make certain the • Rotate the handle to supply roll, grasp the laminated starter section by the leading edge film. • Route over the bottom idler bar adjacent to the lower rubber roller. • Make sure the film is inserted squarely. Rotate the handle 1/4 turn in the direction of the arrows. lower film is tight. If necessary, rotate the supply roll in the direction of the arrows until the film is taut.
PAGE 5
How to apply Front & Back Lamination or Front-Side Lamination/Back-Side Permanent Adhesive Transfer Step 1: Step 2: • Pull back on the paddle so that it is in • Push forward on the paddle to lock the • Insert a document so the leading edge is under the paddle. The document should extend past the edge of the paddle 1-2 inches (2.5-5cm). • Ensure that the leading edge of the the “up” position.
PAGE 6
How to apply Back-Side Permanent Adhesive Transfer • Steps 1, 2 and 3... same as above. • Remove the protective clear mask layer and discard. • This process removes excess adhesive • Remove the document from the white release liner when you’re ready to mount it. from everywhere except the back of the item run through the machine. Replacement Cartridges Product No.
PAGE 7
Supply Roll Removal Step 1 — Step 2 — • Remove the top cover by lifting • Make a small hole with a knife about • Remove the feed tray by lifting and pulling away from the machine. • Slide the knife towards the right upward. one inch (2.54cm) from the left edge of the film. edge of the film and stop about one inch (2.54cm) from the edge. Use caution to avoid cutting into the rubber rollers.
PAGE 8
Maintenance, Safeguards & Tips When properly used, the Xyron 2500 is relatively maintenance-free. Listed below are safeguards and tips that will produce better results. Refer to the exploded view diagram for part descriptions. Importance of a clean document: For best results when laminating, it is highly recommended that the document be cleaned with a soft, lint-free cloth immediately prior to lamination.
PAGE 9
Troubleshooting Symptom Cause Solution Long documents (such as banners) are not aligned with film layers after laminating. Feed Tray not installed correctly or supply roll not seated at base of groove in side plate(s). Verify tray is completely installed such that it is approximately level and square. Also, verify supply rolls are completely seated at base of grooves in side plate(s). Cut Blade does not slide smoothly. Upper Blade Bar sticking in side plate groove or blade sticking on Blade Bar.
PAGE 10
Technical Specifications Mechanical Manual crank driven cold lamination Supplies Replaceable supply roll sets Document size (maximum) 25 in. (63.5cm) wide x length of supply 300 ft. (91.4m) Document thickness range 0.0 to 0.10 in. (2.54mm) Up to 3⁄16" (4.76mm) foam core mounting board with tray removed Machine size/ dimensions (W) 31.5 in. x (L) 28.25 in. x (H) 18.5 in. (W) 80cm x (L) 72cm x (H) 47cm Footprint (L) 15 in. x (W) 27.75 in. (L) 38cm x (W) 71cm Machine weight Approx. 90 lb. (40.