User Manual

APPENDIX “A” ENGINEERING DATA
Pump Size 8x6x13 8x6x17M 8x6x17L 8x6x18 8x8x12 8x8x17 10x8x12S 10x8x12L 10x8x17S 10x8x17L 10x8x20S
K
CASING DATA (All Dimensions in Inches)
125# FF Std Max. Suction Pressure 75 75 75 75 75 75 75 75 75 75 75
f
ASA Flanges Max. Working Pressure 175 175 175 175 175 175 175 175 175 175 175
h
NOMINAL 175 PSI Max. Hydrostatic Test Pressure 262 262 262 262 262 262 262 262 262 262 262
Working Press. Casing material Cast I Cast I Cast I Cast I Cast I Cast I Cast I Cast I Cast I Cast I Cast I
g
250# FF Max. Suction Pressure 200 200 200 200 200 200 200 200 200 200 200
c
NOMINAL 280 PSI Max. Working Pressure 280 280 280 280 280 280 280 280 280 280 280
h
Working Press. Max. Hydrostatic Test Pressure 420 420 420 420 420 420 420 420 420 420 420
Casing material Ductile I Ductile I Ductile I Ductile I Ductile I Ductile I Ductile I Ductile I Ductile I Ductile I Ductile I
g
250# FF Max. Suction Pressure 300 300 300 300 300 300 300 300 300 300 300
d
NOMINAL 400 PSI Max. Working Pressure 400 400 400 400 400 400 400 400 400 400 400
e
Working Press. Max. Hydrostatic Test Pressure 600 600 600 600 600 600 600 600 600 600 600
h
Casing material Ductile I Ductile I Ductile I Ductile I Ductile I Ductile I Ductile I Ductile I Ductile I Ductile I Ductile I
Casing Wall Thickness .44 .44 .44 .44 .44 .44 .44 .44 .50 .50 .62
STUFF BOX DATA (All Dimensions in Inches)
Packing Bore 3.25 3.25 3.25 3.25 3.25 3.75 3.75 3.75 3.75 3.75 3.75
Dimensions Depth 3.50 3.50 3.50 3.50 3.50 3.62 3.62 3.62 3.62 3.62 3.62
Sleeve O.D. 2.25 2.25 2.25 2.25 2.25 2.75 2.75 2.75 2.75 2.75 2.75
Packing Size/No. Rings W/O S. Cage 6.50 6.50 6.50 6.50 6.50 6.50 6.50 6.50 6.50 6.50 6.50
Packing Size/No. Rings W/ S. Cage 5.50 5.50 5.50 5.50 5.50 5.50 5.50 5.50 5.50 5.50 5.50
Seal Cage Width .75 .75 .75 .75 .75 .94 .94 .94 .94 .94 .94
Mech. Seal Bore 2.75 2.75 2.75 2.75 2.75 3.125 3.125 3.125 3.125 3.125
On Shaft Depth 3.00 3.00 3.00 3.00 3.00 3.25 3.25 3.25 3.25 3.25
i
Dimensions Mech. Seal Size (Type 21 or 1) 1.75 1.75 1.75 1.75 1.75 2.000 2.000 2.000 2.000 2.000
Balanced Mech. Major Dia.--> 1.88 1.88 1.88 1.88 1.88 2.12 2.12 2.12 2.12 2.12
l{
Seal Size (Type 1B) Minor Dia.--> 1.75 1.75 1.75 1.75 1.75 2.00 2.00 2.00 2.00 2.00
Mech. Seal Bore 3.38 3.38 3.38 3.38 3.38 4.00 4.00 4.00 4.00 4.00 4.00
On Sleeves Depth 3.00 3.00 3.00 3.00 3.00 3.12 3.12 3.12 3.12 3.12 3.12
Dimensions Mech. Seal Size (Type 21 or 1) 2.25 2.25 2.25 2.25 2.25 2.75 2.75 2.75 2.75 2.75 2.75
Balanced Mech. Major Dia.--> 2.38 2.38 2.38 2.38 2.38 2.88 2.88 2.88 2.88 2.88 2.88
l{
Seal Size (Type 1B) Minor Dia.--> 2.25 2.25 2.25 2.25 2.25 2.75 2.75 2.75 2.75 2.75 2.75
IMPELLER DESIGN DATA (All Dimensions in Inches)
No. of Vanes 7 6 6 6 7 7 6 6 7 5 6
Inlet Area (Sq. Inches) 44.4 29.5 38.7 18.3 61.9 40.2 62.9 57.4 57.5 65.4 68.4
Inlet Velocity per 100 GPM (Ft/Sec) .73 1.09 .83 1.75 .52 .90 .51 .54 .54 .49 .47
Maximum Diameter 12.2 17.0 17.0 17.2 12.8 17.7 12.8 12.8 17.7 17.3 20.2
Minimum Diameter 7.0 10.0 10.0 13.0 8.0 10.0 8.0 8.5 10.0 12.0 12.0
Maximum Sphere 1.0 .47 .50 .70 1.13 .98 1.4 1.47 .97 1.16 .53
WR ^2 for Maximum Diameter (Lbs-Ft^2) 5.3 16.5 18.0 18.0 8.1 17.0 9.8 11.2 20.7 22.4 21.7
j
Wear Ring Clearance – Diam. 175# & 280# W.P. .010-.012 .010-.012 .010-.012 .010-.012 .010-.012 .010-.012 .010-.012 .010-.012 .010-.012 .010-.012 .010-.012
ej
Wear Ring Clearance – Diam. 400# W.P. .020-.024 .020-.024 .020-.024 .020-.024 .020-.024 .020-.024 .020-.024 .020-.024 .020-.024 .020-.024 .020-.024
SHAFT AND BEARING DATA (All Dimensions in Inches)
Under Sleeve 1.874 1.874 1.874 1.874 1.874 2.374 2.374 2.374 2.374 2.374 2.374
Under Mech. Seal on Shaft Type 21 or Type 1 1.750 1.750 1.750 1.750 1.750 2.000 2.000 2.000 2.000 2.000
Under Mech. Seal on Shaft Type 1B 1.875 1.875 1.875 1.875 1.875 2.125 2.125 2.125 2.125 2.125
At Coupling 1.375 1.375 1.375 1.375 1.375 1.625 1.625 1.625 1.625 1.625 1.625
Thru Impeller with Packing – Mech. Seal on Sleeve 1.937 1.937 1.937 1.937 1.937 2.437 2.437 2.437 2.437 2.437 2.437
k
Thru Impeller with Mech. Seal on Shaft 1.939 1.939 1.939 1.939 1.939 2.439 2.439 2.439 2.439 2.439
Shaft Span Bearing to Bearing Centerline 27.25 27.25 27.25 27.25 27.25 29.90 29.90 29.90 29.90 29.90 29.90
Inboard 6208 6208 6208 6208 6208 6309 6309 6309 6309 6309 6309Ball Bearings
Outboard 5307 5307 5307 5307 5307 5308 5308 5308 5308 5308 5308
Packing F20-D4 F20-D4 F20-D4 F20-D4 F20-D4 F20-E4 F20-E4 F20-E4 F20-E4 F20-E4 F20-E4
Mech. Seal on Shaft F20-D5 F20-D5 F20-D5 F20-D5 F20-D5 F20-E5 F20-E5 F20-E5 F20-E5 F20-E5 F20-E5
Frame Designation
Mech. Seal on Shaft Sleeve F20-D6 F20-D6 F20-D6 F20-D6 F20-D6 F20-E6 F20-E6 F20-E6 F20-E6 F20-E6 F20-E6
c With 250# FF flanges and 280# PSIG working pressure refer to pump as
M3x2x11S.
d With 250# FF flanges and 400# PSIG working pressure refer to pump as
H3x2x11S.
e For pumps with 400 PSI working pressure, wear ring clearances are doubled.
Derate pump efficiencies by 2 percentage points.
f Flange dimensions are in accordance with ANSI A21.10, AWWA C110 & ANSI
B16.1 class 125.
g Flange dimensions are in accordance with ANSI B16.1 class 250 except flanges
are flat faced, i.e. FF.
h The hydrostatic test will be accordance with the latest edition of the Hydraulic
Institute Standards, test will maintained for a minimum of 5 minutes.
i Type 1 and 21 seals have the same working lengths.
j For bronze impellers and casing rings. For diametral clearances for other
materials, consult factory.
l Impeller is a light press fit on shaft, do not use construction with stainless steel
impellers.
K Not available in mechanical seal on shaft arrangement.
55