User Manual

APPENDIX “A” ENGINEERING DATA
Pump Size 6x4x12L 6x4x12XL 6x4x14S 6x4x14L 6x6x9 8x6x9 8x6x10 8x6x12S 8x6x12M 8x6x12L 8x6x12XL
K
CASING DATA (All Dimensions in Inches)
125# FF Std Max. Suction Pressure 75 75 75 75 75 75 75 75 75 75 75
f
ASA Flanges Max. Working Pressure 175 175 175 175 175 175 175 175 175 175 175
h
NOMINAL 175 PSI Max. Hydrostatic Test Pressure 262 262 262 262 262 262 262 262 262 262 262
Working Press. Casing material Cast I Cast I Cast I Cast I Cast I Cast I Cast I Cast I Cast I Cast I Cast I
g
250# FF Max. Suction Pressure 200 200 200 200 200 200 200 200 200 200 200
c
NOMINAL 280 PSI Max. Working Pressure 280 280 280 280 280 280 280 280 280 280 280
h
Working Press. Max. Hydrostatic Test Pressure 420 420 420 420 420 420 420 420 420 420 420
Casing material Ductile I Ductile I Ductile I Ductile I Ductile I Ductile I Ductile I Ductile I Ductile I Ductile I Ductile I
g
250# FF Max. Suction Pressure 300 300 300 300 300 300 300 300 300 300 300
d
NOMINAL 400 PSI Max. Working Pressure 400 400 400 400 400 400 400 400 400 400 400
e
Working Press. Max. Hydrostatic Test Pressure 600 600 600 600 600 600 600 600 600 600 600
h
Casing material Ductile I Ductile I Ductile I Ductile I Ductile I Ductile I Ductile I Ductile I Ductile I Ductile I Ductile I
Casing Wall Thickness .375 .375 .50 .50 .50 .50 .50 .50 .44 .44 .44
STUFF BOX DATA (All Dimensions in Inches)
Packing Bore 2.625 2.625 2.625 2.625 2.625 2.625 3.25 2.625 3.25 2.625 2.625
Dimensions Depth 2.56 2.56 2.56 2.56 2.56 2.56 3.50 2.56 3.50 2.56 2.56
Sleeve O.D. 1.875 1.875 1.875 1.875 1.875 1.875 2.25 1.875 2.25 1.875 1.875
Packing Size/No. Rings W/O S. Cage 6.375 6.375 6.375 6.375 6.375 6.375 6.50 6.375 6.50 6.375 6.375
Packing Size/No. Rings W/ S. Cage 5.375 5.375 5.375 5.375 5.375 5.375 5.50 5.375 5.50 5.375 5.375
Seal Cage Width .50 .50 .50 .50 .50 .50 .75 .50 .75 .50 .50
Mech. Seal Bore 2.25 2.25 2.25 2.25 2.25 2.25 2.25
On Shaft Depth 2.62 2.62 2.62 2.62 2.62 2.62 2.62
i
Dimensions Mech. Seal Size (Type 21 or 1) 1.38 1.38 1.38 1.38 1.38 1.38 1.38
Balanced Mech. Major Dia.--> 1.50 1.50 1.50 1.50 1.50 1.50 1.50
l{
Seal Size (Type 1B) Minor Dia.--> 1.38 1.38 1.38 1.38 1.38 1.38 1.38
Mech. Seal Bore 3.00 3.00 3.00 3.00 3.00 3.38 3.00 3.00
On Sleeves Depth 2.56 2.56 2.62 2.62 2.62 2.88 2.62 2.62
Dimensions Mech. Seal Size (Type 21 or 1) 1.875 1.875 1.875 1.875 1.875 2.25 1.875 1.875
Balanced Mech. Major Dia.--> 2.00 2.00 2.00 2.00 2.00 2.38 2.00 2.00
l{
Seal Size (Type 1B) Minor Dia.--> 1.88 1.88 1.88 1.88 1.88 2.25 1.88 1.88
IMPELLER DESIGN DATA (All Dimensions in Inches)
No. of Vanes 6 7 6 6 6 6 6557 7
Inlet Area (Sq. Inches) 19.1 28.4 19.1 22.9 5.9 12.0 15.2 27.0 20.4 38.9 40.6
Inlet Velocity per 100 GPM (Ft/Sec) 1.7 1.1 1.7 1.4 5.4 2.7 2.1 1.2 1.6 .83 .79
Maximum Diameter 12.8 14.0 13.8 13.8 9.8 9.8 10.0 12.8 12.8 12.8 13.7
Minimum Diameter 6.0 7.0 6.5 7.0 6.5 6.5 7.6 7.0 6.5 7.0 7.0
Maximum Sphere .60 .37 .47 .68 .48 .64 .75 .72 .87 1.0 1.0
WR ^2 for Maximum Diameter (Lbs-Ft^2) 3.1 3.5 7.5 8.0 2.5 2.6 3.1 3.6 3.7 3.8 8.5
j
Wear Ring Clearance – Diam. 175# & 280# W.P. .010-.012 .010-.012 .010-.012 .010-.012 .010-.012 .010-.012 .010-.012 .010-.012 .010-.012 .010-.012 .010-.012
ej
Wear Ring Clearance – Diam. 400# W.P. .020-.024 .020-.024 .020-.024 .020-.024 .020-.024 .020-.024 .020-.024 .020-.024 .020-.024 .020-.024 .020-.024
SHAFT AND BEARING DATA (All Dimensions in Inches)
Under Sleeve 1.499 1.499 1.499 1.499 1.499 1.499 1.874 1.499 1.874 1.499 1.499
Under Mech. Seal on Shaft Type 21 or Type 1 1.375 1.375 1.375 1.375 1.375 1.375 1.375
Under Mech. Seal on Shaft Type 1B 1.500 1.500 1.500 1.500 1.500 1.500 1.500
At Coupling 1.125 1.125 1.125 1.125 1.125 1.125 1.375 1.125 1.375 1.125 1.125
Thru Impeller with Packing – Mech. Seal on Sleeve 1.686 1.686 1.686 1.686 1.687 1.687 1.937 1.686 1.937 1.686 1.686
k
Thru Impeller with Mech. Seal on Shaft 1.689 1.689 1.689 1.689 1.689 1.689 1.689
Shaft Span Bearing to Bearing Centerline 22.90 22.90 22.90 22.90 22.00 25.25 25.25 22.90 25.25 22.90 22.90
Inboard 6206 6206 6206 6206 6206 6206 6208 6206 6208 6206 6206Ball Bearings
Outboard 5206 5206 5206 5206 5206 5206 5307 5206 5307 5206 5206
Packing F20-C4 F20-C4 F20-C4 F20-C4 F20-G4 F20-H4 F20-I4 F20-C4 F20-B4 F20-C4 F20-C4
Mech. Seal on Shaft F20-C5 F20-C5 F20-C5 F20-C5 F20-C5 F20-C5 F20-C5
Frame
Designation
Mech. Seal on Shaft Sleeve F20-C6 F20-C6 F20-C6 F20-C6 F20-C6 F20-B6 F20-C6 F20-C6
c With 250# FF flanges and 280# PSIG working pressure refer to pump as
M3x2x11S.
d With 250# FF flanges and 400# PSIG working pressure refer to pump as
H3x2x11S.
e For pumps with 400 PSI working pressure, wear ring clearances are doubled.
Derate pump efficiencies by 2 percentage points.
f Flange dimensions are in accordance with ANSI A21.10, AWWA C110 & ANSI
B16.1 class 125.
g Flange dimensions are in accordance with ANSI B16.1 class 250 except flanges
are flat faced, i.e. FF.
h The hydrostatic test will be accordance with the latest edition of the Hydraulic
Institute Standards, test will maintained for a minimum of 5 minutes.
i Type 1 and 21 seals have the same working lengths.
j For bronze impellers and casing rings. For diametral clearances for other
materials, consult factory.
l Impeller is a light press fit on shaft, do not use construction with stainless steel
impellers.
K Not available in mechanical seal on shaft arrangement.
54