V IE W XVMIRROR USER MANUAL For more information on the Xview range go to our website xviewdrive.com.au INCLUSIONS: Dash Cam, GPS Power Cable, 12/24V In-Car USB Charger, Micro SD Card, Adhesive Surface Mount, Rear Camera & Rear Camera Cable.
1. PRODUCT FEATURES AND SPECIFICATIONS Mirror Display • 4.3” 16:9 High-resolution TFT LCD Screen • Resolution 480*272 • Clip-On mount extends 53-70mm • 12V Compatible • PAL video standard • Power Supply: DC12V +/- 10% • Video Input : Yellow = Reverse Camera Input • Secondary Video RCA Input • Dimensions 75(H) x 37(W) x 285mm(L) Butterfly Camera • 120 Degree wide angle lens • Parking guide lines • IP-67 Dust and water protection • Surface plate mount • CMOS Sensors • 0.
2. TABLE OF CONTENTS Product features and specifications......................................2 Table of contents..................................................................3 Installation diagram..............................................................4 Installing the camera............................................................5 Installation of the Mirror Display...........................................7 Testing the reverse camera function....................................
3. INSTALLATION DIAGRAM Mirror F M F Moulded splitter F M Powerwires + (ACC) M F F (Optional front camera) 6 Metres F M (Red wires can be used for additional accessories ) + Moulded splitter Powerwires (Reversing light) F M Camera The Clip on mirror design securely mounts on the existing rear view mirror in the vehicle by expanding the clamping arms at the back.
4. INSTALLING THE CAMERA In most instances, the camera is best mounted above the vehicles license plate as shown here. Hole for cable 1. Connect the RED wire of the Cameras Power Harness to the wire that supplies power to the reversing light globe (the wire that is energized only when the car is put into reverse). Before making the electrical connection, temporarily disconnect the camera from the power plug whilst making the connection to the reversing light globe.
5. INSTALLING THE CAMERA CONT.... module (sold separately) may need to be installed. However, just because the vehicle has a CAN BUS system does not necessarily mean that it will require such a module to work. In fact the opposite is true. Most vehicles do not require an additional module. If a CAN BUS module is required we recommend seeking advice from a professional installer. 2. After you have insulated the join you can connect the power harness to the camera.
6. INSTALLATION OF THE MIRROR DISPLAY 4. The display has two power wires to be connected. Connect the red wire (accessories +12V) to a wire that is energized when the vehicles accessories is turned on. Connect the black wire to a ground earth wire or to the body of the car using the steel of the cars body behind the kick trim as an earth. In this case drill a small hole and connect the wire using a suitable ring terminal. Scrape off the cars paint around the hole to ensure good earth. 5.
. MENU OPTIONS AND SETTINGS 1. Press the Middle button for Menu access functions (see Fig.1) 2. Press the Top button repeatedly to increase value 3.
. TROUBLESHOOTING GUIDE Problem: The Mirror Display feels warm when it is operating Solution: • It is normal for the Mirror Display to feel warm to the touch during typical use. Problem: My screen image is blurry, dirty or discoloured Solution: • Check to see if there are any finger prints or dirt present on the camera lens. If needed, clean with a soft dry cloth before recording. • Also be sure to have removed the transparent lens/screen cover during installation.
. SAFETY INFORMATION & WARNINGS Do not use the Mirror display in damp working conditions; the Mirror Display is not waterproof. Do not try opening the shell or trying to repair the Mirror Display by yourself. If the accessories for the Mirror Display have any problems, please take it to an authorised repair agent for repair. Do not use a chemical substance, cleaning solvent or cleaner to clean the Mirror Display, please use a moist soft cloth if you would like to clean the Mirror Display.
. USER SUPPORT If you need assistance setting up or have an issue regarding the use of your Xview product contact Xview Customer Support. Australian Agent: TEL: 03 – 8587 8898 FAX: 03 – 8587 8866 Mon-Fri 9am – 5pm AEST For more information, manuals, software or other products in the Xview range please go to our website. Xviewdrive.com.au This manual is considered correct at time of printing but is subject to change. For latest manuals and updates refer to the website.
