Installation Guide

ManualsBrandsXtremepowerUS ManualsOutdoors4 ft. W x 12 ft. H In-Ground Pool Safety Fence DIY Latch Magnetic Gate in Beige

XtremepowerUS Pool Equipment

Service Phone: 909-628-0880

Monday to Friday 9am-3pm (PST)

Index

◎ Getting Started

◎ Section1: Layout and Marking Out Your Deck

◎ Section2: Understanding How to Drill

◎ Section3: Drilling and Inserting Ground Sleeves

◎ Section4: Making Your Custom Cut

◎ Section5: Finishing and Latching Your New Pool Fence

TOOLS

REQUIRED

1. Hammer Drill 8.

Scissors

2. 5/8'' Masonry Bit(14''+) 9. Household

Stapler

3. Extension Cord 10.#2 Square Head Screw

Tip

4. Tape Measure 11.1/8'' Metal Drill

Bit

5. Hammer 12.Cordless Screw

Gun

6. Marker

13.1-Template(Incl.)

7. Garden Hose 14.Chalk

Line

Each Fence Section Includes :1 Mark Out Template,1 Latch,5

Ground Sleeves,5 Ground Caps

NOTE: Fence sections are 12'of pool fence mesh

bordered on all four sides with 5 fence poles

spaced every 36''

REMEMBER : Nothing replaces direct adult supervision. Never leave a

child unattended.

(Read Instructions Completely Before

Beginning)

Summary of content (14 pages)

PAGE 1
XtremepowerUS Pool Equipment Service Phone: 909-628-0880 Monday to Friday 9am-3pm (PST) Index ◎ Getting Started ◎ Section1: Layout and Marking Out Your Deck ◎ Section2: Understanding How to Drill ◎ Section3: Drilling and Inserting Ground Sleeves ◎ Section4: Making Your Custom Cut ◎ Section5: Finishing and Latching Your New Pool Fence TOOLS REQUIRED 1. Hammer Drill 2. 5/8'' Masonry Bit(14''+) 3. Extension Cord Tip 4. Tape Measure 5. Hammer 6. Marker 7. Garden Hose 8. Scissors 9. Household Stapler 10.
PAGE 2
Step 1: Layout & Mark-Out **If using a self-closing gate, skip this step and refer to the instructions included in the gate box * Layout: The fence should be a minimum 2' off the pool edge. See Fig.1&Fig 2 * Start Point: Is the manual opening to enter the pool area. See Fig 1 Use the double hole on the section template provided and mark your first hole 1L Fig 3. 1L is for the 1st pole of the full section going to the left side of the pool.
PAGE 3
* Then place the template over 1R and mark your second hole for that section(Fig.5a). * Now repeat until pole 5th of the section Fig. 6-7a * Mark your last hole for that section,(hole 5)Fig.7a. * Then use the double hole on the template and align it over the 5th hole you marked Fig.7b and mark the first hole of the next connecting section to the right,(hole).Repeat these steps on the both sides of the pool until you reach the section that will be the cut section. ** See Fig.
PAGE 4
* Custom Cut:Is when the last piece is less than the 36''template. Marking your custom cut is just like marking out a full 3 foot panel only the last panel is usually shorter than 3 feet. This is the custom cut you will make later. This section is the last one marked out, usually in the back of the pool, where you will not notice it. The last piece will most likely have fewer poles in it. This example depicts a two pole cut.
PAGE 5
PRO NOTES: Any hole to be drilled will have a hole in front of it and one in the back of it as shown in Fig.15a. If the hole to be drilled is in the heavy lean range it will require a Heavy Lean. If the hole to be drilled is in the light lean range, it will require a Light Lean. See Fig.
PAGE 6
PRO NOTES :When determining the lean of a hole simply stand over the hole you are about to drill then look at the hole in front of you. If you connected all three holes with a triangle. The point of the triangle indicates the direction of lean. The further away from the imaginary line the more of a lean.If it doesn't make a triangle then it is level. Fig.
PAGE 7
heavy lean is and what a light lean is. (See Fig.
PAGE 8
* Drilling: Begin at your start point to drill out fence as shown below in Fig.18.Check the hole you are about to drill making sure you have the appropriate degree of lean & the direction of the hole to be drilled either towards the pool or away from the pool. In thsi example we are drilling away from the pool. Remember to always adjust your bubble indicator to level. NOTE: Stabilize drill guide with foot pressure to prevent drill guide from sgifting.
PAGE 9
Step 4: Making Your Custon Cut * Measuring Your Custom Cut: Your custom section is the one that doesn't fit. The first step is to measure your custom cut. Note whether you will be cutting from the right side or the left side of the full section. See Fig.21 below PRO NOTE: When measuring for a custom cut or cutting fence you should always remember that the moldings face out away from the pool. When measuring your cut section always face the pool. Measure the outside centerline fo the odd panel.
PAGE 10
PAGE 11
Hold your tape measure on the OUTSIDE OF THE MOLDING as shown in FIg.25. and make a mark on the border at the top and bottom of the fence with a marker. Using your scissord you can proceed to cut the mesh. Sliding your ruler up against the molding to make sure you are cutting at exactly the measurement you took. See Fig.26 Make sure the mesh us tight and remove the extra pole from the extra piece. Your cut has been made and you now have to attach the border material included.
PAGE 12
Now your border has been attached to the cut side of the mesh. Cut of excess bprder. Your next step is to attach the pole you removed in Fig.26 to the cut side. The best way to attach your pole to the cut is as follow: * lay your molding strip on top of the border you just attached. Fig.29 * Line up molding so that it's flush with bottom & flush with line of mesh. Make sure all staples are covered by molding Fig.
PAGE 13
in Fig.32. Use the latch for leverage. Then disconnect the latch from the screw eye and turn the other screw eye in using the latch for leverage. Make sure both screw eyes are tightened until there are no visible threads. The fence works on tension so you must squeeze the poles together in order to connect the latch to the screw eye.(TIP) Before you squeeze the poles together make sure that the poles are straight. The tension of the fence wil want to twist the poles away from each other.
PAGE 14
Safety Reminder * keep gates and manual openings closed at all times. * Periodically check fence for proper function. * The Fence must block all entrances to the pool area. * Keep fence away from staging plaforms ie:tables or chairs. * Leave room between fence & pool to allow for a walkway while fence is * If fence is terminating to an existing structure make sure the structure is solid enough and the latch can not pull out allowing a child to et through.