SWIMMING POOL HEAT PUMP Owner's Manual 1 Manual
SWIMMING POOL HEAT PUMP Manual Contents 1. Introduction ............................................................................................................... 3 2.Heat Pump Technical Specifications .......................................................................... 4 3. Structure of Heat Pump ............................................................................................ 5 4. Installation Instructions ............................................................................
SWIMMING POOL HEAT PUMP Manual 1. Introduction The pool heat pump is a self-contained unit designed specifically for pool heating. Each component has been selected with care to achieve a high-quality product in an effort to exceed all industry standards. All pool heat pumps have an electronic board with service analyzer, a titanium heat exchanger tube warranted for 10 years against corrosion and PVC plastic cabinet that eliminates all maintenance for life.
SWIMMING POOL HEAT PUMP 2.
SWIMMING POOL HEAT PUMP Manual 3. Structure of Heat P Pump Figure 1.
SWIMMING POOL HEAT PUMP Manual Figure 2.
SWIMMING POOL HEAT PUMP As the picture shows, the components of the heat pump is listed in the form. Table1. Parts of Heat Pump NO.
SWIMMING POOL HEAT PUMP Manual Figure 3. Titanium Heat Exchanger Exc Exploded View ² As the picture shows, the titanium exchanger exchanges heat with the refrigerant and offers high resistance to chemical products while ensuring an excellent heat exchange. Table2.. Parts of Titanium Heat Exchanger No. Parts of heat exchanger No.
SWIMMING POOL HEAT PUMP Manual Figure 4. SHAS-32/53/65/80H 32/53/65/80H-UC Electrical Box Exploded View Table3. Parts of SHAS SHAS-32/53/65/80H-UC Electrical Box No. Parts of Electrical Box No.
SWIMMING POOL HEAT PUMP Manual Figure 5. SHAS-95H 95H-UU Electrical Box Exploded View Table4. Parts of SHAS SHAS-95H-UU Electrical Box No. Parts of Electrical Box No.
SWIMMING POOL HEAT PUMP Manual Figure 5. SHAS-110/125/137H 110/125/137H-UU Electrical Box Exploded View Table5. Parts of SHAS SHAS-110/125/137H-UU Electrical Box No. Parts of Electrical Box No.
SWIMMING POOL HEAT PUMP Manual 4. Installation Instructions 4.1 Location The placement of the pool heater is very important in keeping installation costs to a minimum while providing for maximum efficiency of operation, as well as allowing adequate access for service and maintenance. The pool heat pump is designed for outdoor installation and should not be installed in a fully enclosed area, such as a shed, garage, etc.
SWIMMING POOL HEAT PUMP Manual 4.2 Water Piping ² Single Unit Installation Figure 6 illustrates the standard plumbing layout with a single heat pump unit. Following the diagram from right to left, the plumbing sequence is as follows: Pool > Pool Pump > Filter > Heat Pump > Check Valve > Chemical Feeder > Pool. Note For normal installations, do not install a shutoff valve or any kind of variable restriction in the water piping between the heat pump outlet and the pool/spa.
SWIMMING POOL HEAT PUMP Wire Conduits Power Supply and Grounding Check Valve Bypass Valves Chemical Feeder Filter Pool Pump Heat Pump Figure 6.
SWIMMING POOL HEAT PUMP Figure 7. Plumbing lumbing For Heating System Combinations Figure 8.
SWIMMING POOL HEAT PUMP Manual Figure 9. Four(4) Heat Pump Plumbing Layout ² Important Certain installations have valves which isolate the heat pump from the water circuit. If the heat exchanger is deprived of water circulation for several days, high chlorine gas could cause excessive corrosion. If the disconnect switch is turned off, be sure that the pool water is allowed to circulate through the unit, or is drained out of it.
SWIMMING POOL HEAT PUMP Manual 5. Electrical Connections 5.1 Electrical The wiring of your pool heat pump should be performed by a qualified electrician in accordance with local requirements. A properly-sized breaker and copper wire must be used. Check the heat pump data label for required maximum breaker size ² Important The unit must always be powered off before opening the access panel. 5.
SWIMMING POOL HEAT PUMP L1 Ground L2 Manual G Figure 10.
SWIMMING POOL HEAT PUMP 6. Wiring Diagram Figure 11.
SWIMMING POOL HEAT PUMP Figure 12.
SWIMMING POOL HEAT PUMP Figure 13.
SWIMMING POOL HEAT PUMP Figure 14.
SWIMMING POOL HEAT PUMP Manual 7.. Service Analyzer Control The control panel is factory set to display the te temperature mperature in Fahrenheit degrees, degrees it can also be displayed as degree centigrade centigrade. 7.1 Panel Description Temperature and parameter display screen To lower the desired temperature or to change parameters To raise the desired temperature or to change parameters Display light Switch on/off on/o Timer which sets and adjusts the running time with the " and " button.
SWIMMING POOL HEAT PUMP Long press the " the item with the " Manual " button for 10s to examine the running parameter, change and " button to check the measure value. Figure 16. Parameter Table ² For Example: Display "026.5", it means the inlet water temperature is 26.5℃； 26.5 Display"146.5", it means discharge temperature is 46.5 46.5℃ 7.2 Operation ² To increase the temperature Proceed as explained above using the up arrow to increase the temperature setting 0.5 degree at a time.
SWIMMING POOL HEAT PUMP Manual 8. Service Analyzer Codes Most problems will be detected by the service analyzer and a code will be displayed on the digital display of your heater. The meaning of Display Codes are as follows: Figure 17.
SWIMMING POOL HEAT PUMP Manual 9. Troubleshooting The pool heater is not running Heat pump control set to OFF Turn the heat pump on Desired water temperature is reached Unit will automatically restart when the water temperature goes below the set point Main breaker is tripped Reset main breaker and restart heat pump Filter is dirty, restricting the water flow.
SWIMMING POOL HEAT PUMP Manual There is water around the unit While your pool heater is in the heating mode, a large quantity of warm and humid air passes over the evaporator and causes condensation. It is normal to see condensation dripping under the heater. To check if the water really is a leak, you must stop the heater and leave the pool pump running for over 5 hours. If water is still coming out of your heater after this period, then call your dealer for service.
SWIMMING POOL HEAT PUMP Manual 10. Initial Startup ² Before starting the pool heater for the first time, it is important to verify that the breaker is in the ON position. ² Also make sure that the water circulates freely and that the pool pump is activated. ² Then, you will need to set the water temperature you desire. The fan will immediately start. The compressor will start after a 3 to 4-minute delay.
SWIMMING POOL HEAT PUMP Manual 11. Requesting Assistance or Service ² All service will be handled by the dealer that you bought the unit from. Do not return the heater to your dealer, give them a call and they will schedule a service call. ² Before calling for assistance or service, please check the “Troubleshooting” (pp. 16-17) and “Warranty” (pp. 21) sections or call your dealer. It may save you the cost of a service call. If you still need help, follow the instructions below.
SWIMMING POOL HEAT PUMP Manual Please read carefully Record your model’s information Please complete and mail in the ownership registration card provided with this guide. The return address is displayed on the front of your registration card. Simply mail it as you would a postcard. The card helps us notify you about any new information about your heater. Whenever you call to request service for your heater, you must know your complete model and serial numbers.
SWIMMING POOL HEAT PUMP Notes 31 Manual
