Instructions / Assembly

MINI TRACKED DUMPER
18
GB
5. Inspect for any loose or damaged parts.
Repair or replace damaged parts and
tighten loose screws, nuts or bolts.
6. Store your unit on flat ground in a clean, dry
building that has good ventilation.
STORAGE
Transporting
HYDRULIC SCHEME
If the mini tracked dumper will not be used for
a period longer than 30 days, follow the steps
below to prepare your unit for storage.
1. Drain the fuel tank completely. Stored fuel
containing ethanol or MTBE can start to go
stale in 30 days. Stale fuel has high gum
content and can clog the carburetor and
restrict fuel flow.
2. Start the engine and run until it stops. This
helps prevent gum deposits from forming
inside the carburetor and possible engine
damage.
3. While the engine is still warm, drain the oil
Do not use strong detergents or
petroleum based cleaners when
cleaning plastic parts. Chemicals
can damage plastics.
Do not store the machine with fuel
in a non-ventilated area where fuel
fumes may reach flame, sparks,
pilot lights or any ignition sources.
Oil Cylinder
Oil Pump
A
P
T
B
(25MP, 2.5ml/r)
Oil Tank
Reversal Valve
Oil Filter
Oil Relief Valve
from the engine. Refill with fresh oil of the
grade recommended in the Engine Manual.
4. Use clean cloths to clean off the outside of
the machine and to keep the air vents free
of obstructions.
For long distance transport, the machine is
equipped with lifting rings for hoist.
Use a crane to lift up the machine with a
reliable chain, rope or strap fixed through the
lifting rings as shown in the figure.
09737UK00M100_更新回收处理标志.indd 18 2019/9/4 11:01:53
MINI TRACKED DUMPER
19
GB
TROUBLE SHOOTING
Problem Cause Remedy
Engine fails to
start
1. Spark plug wire is disconnected
2. Out of fuel or stale fuel
3. Engine and/or Fuel valve is not in
ON position
4. Choke lever is not in CLOSE
position
5. Blocked fuel line
6. Fouled spark plug
7. Engine flooding
8. Belt tension lever is engaged
1. Attach spark plug wire securely
to spark plug
2. Fill with clean, fresh gasoline
3. Engine and Fuel valve must be in
ON position
4. Choke level must be in CLOSE
position for a cold start
5. Clean fuel line
6. Clean, adjust gap, or replace
7. Wait a few minutes to restart, but
do not prime
8. Disengage the belt tension lever
Engine runs
erratically
1. Spark plug wire is loose
2. Unit running with Choke lever in
CLOSE position
3. Blocked fuel line or stale fuel
4. Vent plugged
5. Water or dirt in fuel system
6. Dirty air cleaner
7. Improper carburetor adjustment
1. Connect and tighten spark plug
wire
2. Move choke lever to OPEN
position
3. Clean fuel line. Fill tank with
clean, fresh gasoline
4. Clear vent
5. Drain fuel tank. Refill with fresh
fuel
6. Clean or replace air cleaner
7. Refer to engine manual
Engine overheats
1. Engine oil level low
2. Dirty air cleaner
3. Air flow restricted
4. Carburetor not adjusted properly
1. Fill crankcase with proper oil
2. Clean air cleaner
3. Remove housing and clean
4. Refer to engine manual
One of the two
tracks is blocked
Foreign bodies have worked their
way between the track and the frame
Remove the foreign body
Machine does not
move while engine
is running
1. Gear is not properly selected
2. Driving tracks not tight enough
1. Ensure gear lever is not in-
between two different gears
2. Tighten driving tracks
09737UK00M100_更新回收处理标志.indd 19 2019/9/4 11:01:53