GB TABLE OF CONTENTS Introduction 2 Specifications 2 Symbols 3 Safety 4 General Safety Rules 4 Specific Safety Rules 6 Unpacking the Container 7 Contents Supplied 8 Know your Machine 9 Features & Controls 9 Operation 11 Maintenance 13 Transporting 18 Storage 18 Hydraulic Scheme 18 Trouble Shooting 19 Parts Schedule 20 Parts List 22 INTRODUCTION Your new mini tracked dumper will more than satisfy your expectations.
RECYCLING AND DISPOSAL GB Keep your hands clear from all rotating parts. This marking indicates that this product should not be disposed with other household wastes. To prevent possible harm to the environment or human health from uncontrolled waste disposal, recycle it responsibly to promote the sustainable reuse of material resources. To return your used device, please use the return and collection systems or check with your local authority or local stores for advice of environmental safe recycling.
SAFETY GB General Safety Rules Understand Your Machine Read this manual and labels affixed to the machine to understand its limitations and potential hazards. Be thoroughly familiar with the controls and their proper operation. Know how to stop the machine and disengage the controls quickly. Make sure to read and understand all the instructions and safety precautions as outlined in the Engine Manufacturer’s manual packed separately with your unit.
on the unit. Transporting or performing maintenance or service on a machine with its switch on invites accidents. If the machine should start to vibrate abnormally, stop the engine (motor) and check immediately for the cause. Vibration is generally a warning sign of trouble. Engine Safety This machine is equipped with an internal combustion engine.
GB Specific Safety Rules Thoroughly inspect the area to be worked. Keep the working area clean and free of debris to prevent tripping. Operate on flat, level ground. Never place any part of your body where it would be in danger if movement should occur during assembly, installation, operation, maintenance, repair, or relocation. Keep all bystanders, children, and pets at least 23m away. If you are approached, stop the unit immediately. Do not mount anything on the hopper and never carry passengers.
UNPACKING THE CONTAINER GB Use the screwdriver and hammer to open all the side locks. 500 Item # 09737 6,5 HP QTY : 1GW: 298.5 kg NW: 255.5 kg Cart on S 167.5 ize: X 75 .5 X 11 2.5 c m per CZ Mini-Dum Dumper ed ck GB Mini Tra ndumper DE Miniraupe orter IT Minitrasp 9,0 HP ɬɟɪ RU Ɍɪɚɧɫɩɨɪ 1 2 3 4 Remove all the plywood plates, and remove all the loose parts on the bottom pallets. MINI TRACKED DUMPER 09737UK00M100_更新回收处理标志.
CONTENTS SUPPLIED GB The mini tracked dumper comes partially assembled and is shipped in carefully packed package. After all the parts have been removed from the package, you should have: 1 2 3 1. Machine 3. Tools for Spark Plug Assembly 2. Operator’s Manual & Engine Manual 8 MINI TRACKED DUMPER 09737UK00M100_更新回收处理标志.
KNOW YOUR MACHINE GB Features and Controls Engine Switch Throttle Control Right Steering Lever Clutch Control Lever Left Steering Lever Hydraulic Tipping Handle Gear Selection Lever High/Low Speed Shifting Handle Track Hopper Recoil Starter Handle Choke Control Fuel Shut-Off Valve MINI TRACKED DUMPER 09737UK00M100_更新回收处理标志.
GB Gear Selection Lever The gear selection lever has 4 positions: 3 forward speeds and 1 reversefor both high and low speed.To change speeds, move the speed shift lever to the desired position. The lever locks in a notch at each speed selection. To raise the hopper, pull the tipping handle upwards (as Ill. B in the figure) until the hopper has reached the desired position. To stop raising the hopper, simply release the tipping handle and return the locking plate to its original position.
Engine On/Off Switch Operation The engine switch has two positions. OFF engine will not start or run. ON - engine will start and run. Recoil Starter Handle The Recoil Starter Handle is used to start the engine. GB Add Oil To Engine No oil in the engine originally, but a bottle of engine oil is in scope of delivery. Don’t start the engine before adding oil. Fuel Shut-Off Valve The fuel shut – off has two position. ) - use this position to service, CLOSED ( transport, or store the unit.
GB IMPORTANT: DO NOT OVERFILL! This equipment and/or its engine may include evaporative emissions control system components, required to meet EPA and/or CARB regulations, that will only function properly when the fuel tank has been filled to the recommended level. Overfilling may cause permanent damage to evaporative emissions control system components. Filling to the recommended level ensures a vapor gap required to allow for fuel expansion.
Avoid sharp turns and frequent changes of direction while driving on rough, hard terrains full of sharp, uneven points with a high degree of friction. Even though the unit has rubber tracks, remember to be careful when working in adverse weather conditions (ice, heavy rain and snow) or on types of ground that could make the mini tracked dumper unstable. Please note that as this is a tracked vehicle, it is subject to a considerable pitching movement when passing over bumps, holes and steps.
GB 3. Once tightness is set, return the jam nut against the handle to hold the cable in place. 1. Loosen the jam nut by turning it counter clockwise with 12mm wrench. 1 Jam Nut Jam Nut 2. Tighten or loosen the cable by turning the cable adjustment nut clockwise or counter clockwise with 10 mm wrench until you have reached your required tightness. 3. Once tightness is set, return the jam nut against the handle to hold the cable in place.
Remove all the screws and washers from both belt covers and take off the covers. Lubrication GB General Lubrication Lightly lubricate all moving parts of the machine at end of the season or every 25 operating hours. Gearbox Lubrication M6×12 (×2) The gearbox is pre-lubricated and sealed at the factory. Unless there is evidence of leakage or service has been performed on the gearbox, no additional lubricate should be required until 50 hours use. After first 50 hours use, change all the gear oil.
GB Hydraulic Oil Tightening Tracks Unscrew the locking nut to drain the oil into the pan. With use, tracks tend to loosen. When operating with loose tracks, they tend to slip over the driving wheel causing it to jump its housing, thus damaging wear to the housing. To check track tightness, proceed as follows. 1. Set the machine on a flat surface with compact ground, or on asphalt or pavement. M14 x 1.5 2.
Adjust the bolt M20x180 to move the guiding wheel assembly toward the driving wheels. Then the track will get loose. GB M20×180 M20×180 Caution: Do not over-tighten your track. The adjustment of the track and the brakes are linked. The braking power will lessen the more the track is tightened. Pull out the loosen tracks . If the adjustment bolt has no more adjustment left, the tracks may have to be replaced. Replacing Tracks Check the condition of the tracks periodically.
GB Transporting For long distance transport, the machine is equipped with lifting rings for hoist. from the engine. Refill with fresh oil of the grade recommended in the Engine Manual. 4. Use clean cloths to clean off the outside of the machine and to keep the air vents free of obstructions. Use a crane to lift up the machine with a reliable chain, rope or strap fixed through the lifting rings as shown in the figure. Do not use strong detergents or petroleum based cleaners when cleaning plastic parts.
TROUBLE SHOOTING Problem Engine fails to start Cause GB Remedy 1. Spark plug wire is disconnected 1. Attach spark plug wire securely to spark plug 2. Out of fuel or stale fuel 2. Fill with clean, fresh gasoline 3. Engine and/or Fuel valve is not in ON position 3. Engine and Fuel valve must be in ON position 4. Choke lever is not in CLOSE position 4. Choke level must be in CLOSE position for a cold start 5. Blocked fuel line 5. Clean fuel line 6. Fouled spark plug 6.
PARTS SCHEDULE GB 09737 Machine 20 MINI TRACKED DUMPER 09737UK00M100_更新回收处理标志.
09737 Gearbox (50) GB MINI TRACKED DUMPER 21
Parts List GB No. 22 Description Q'ty No.
No. Description Q'ty No. Description GB Q'ty 81 Knuckle Bearing SQ6-RS 2 121 Adjusting Shaft 2 82 Screw M10x60 2 122 Hexagon Thin Nut M20 2 83 Driving Wheel 2 123 Connecting Pipe 2 84 Gear Shifting Lever 1 124 Guide Spring 2 85 Bolt M10x35 3 125 Guide Wheel Adjusting Part 2 86 Spring 1 126 Cotter Pin ∮4X35 7 87 Gearbox 6+2 1 127 Guide Wheel 2 88 Lock Nut M10 13 128 Axis Pin 2 89 Long Extension Sping 1 129 Guide Wheel Assy.
GB 24 No. Description Q'ty No.
GB 09737A Machine MINI TRACKED DUMPER 09737UK00M100_更新回收处理标志.
09737A Gearbox (50) GB 26 MINI TRACKED DUMPER
Parts List No. Description Q'ty No.
GB 28 No. Description Q'ty No. Description Q'ty 81 Knuckle Bearing SQ6-RS 2 121 Adjusting Shaft 2 82 Screw M10x60 2 122 Hexagon Thin Nut M20 2 83 Driving Wheel 2 123 Connecting Pipe 2 84 Gear Shifting Lever 1 124 Guide Spring 2 85 Bolt M10x35 3 125 Guide Wheel Adjusting Part 2 86 Spring 1 126 Cotter Pin ∮4X35 7 87 Gearbox 6+2 1 127 Guide Wheel 2 88 Lock Nut M10 13 128 Axis Pin 2 89 Long Extension Sping 1 129 Guide Wheel Assy.
No. Description Q'ty No.
OF NOTE PLEASE READ THE FOLLOWING CAREFULLY THE Record Product"s Serial Number Here: _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ Note: If product has no serial nuhlber, record month and year of purchase instead. Note: Sohle parts are Iisted and shO\,Vn for illustration purposes only and are not available individually as replacement parts.
