GB TABLE OF CONTENTS Introduction 2 Specifications 2 Symbols 3 Safety 4 General Safety Rules 4 Specific Safety Rules 6 Specifications Unpacking The Container 7 Contents Supplied 8 Item No. Assembly 8 Engine Know your Machine 10 Transmission 3F+1R Load Capacity 300 kg Box Length 860 mm Features & Controls 10 Operation 12 09715 196cc, 6.
SYMBOLS The rating plate on your machine may show symbols. These represent important information about the product or instructions on its use. Read these instructions carefully. Wear eye protection. Wear hearing protection. GB The exhaust fumes are dangerous, containing carbon monoxide. Staying in the environment can lead to unconsciousness and death. Always turn off the engine before starting maintenance. Keep children and bystanders off and away. Wear protective gloves. Wear safety footwear.
SAFETY GB General Safety Rules Understand Your Machine Read this manual and labels affixed to the machine to understand its limitations and potential hazards. Be thoroughly familiar with the controls and their proper operation. Know how to stop the machine and disengage the controls quickly. Make sure to read and understand all the instructions and safety precautions as outlined in the Engine Manufacturer’s manual packed separately with your unit.
on the unit. Transporting or performing maintenance or service on a machine with its switch on invites accidents. If the machine should start to vibrate abnormally, stop the engine (motor) and check immediately for the cause. Vibration is generally a warning sign of trouble. Engine Safety This machine is equipped with an internal combustion engine.
GB Specific Safety Rules Thoroughly inspect the area to be worked. Keep the working area clean and free of debris to prevent tripping. Operate on flat, level ground. On soft ground, drive at the first forward/ reverse gear. Do not rapidly accelerate, turn sharply or stop. Pay the utmost attention when working on frozen ground, as the machine may tend to skid.
UNPACKING THE CONTAINER GB Use the screwdriver and hammer to open all the side locks. 1 2 3 4 Remove all the plywood plates, and remove all the loose parts on the bottom pallets. MINI TRACKED DUMPER 09715UK00M112_更新回收处理标志_未发排.
GB CONTENTS SUPPLIED The mini tracked dumper comes partially assembled and is shipped in carefully packed package. After all the parts have been removed from the package, you should have: 1 2 3 4 5 6 1. Handles 2. Machine M10 X 20 X4 M8 X 25 X2 A Gas Spring (Optional) Lift up the hopper and insert a support rod for safety purpose. Align the holes in the gas spring with the holes in both guide brackets and insert M8x35 bolts, washers and nuts to tighten. 3. Gas Spring (Optional) 4.
Plow Blade (Optional) Mount the mounting bracket to the blade using M8X30 hex bolts, washers and nuts. Attach control lever to the guide tube. Line up holes and fasten with M8X35 bolt, washers and nut. GB Insert the handle grip into the holder. Secure the support bracket into the control lever with pin 10x60 and bridge clip. M8×30 (×4) Handle Grip Control Lever M8 X 30 Mounting Bracket X4 10×60 (×1) a Position the pivot bracket inside the mounting bracket and align with mounting bracket holes.
KNOW YOUR MACHINE GB Features and Controls Engine Switch Throttle Control Right Steering Lever Clutch Control Lever Left Steering Lever Hopper Tipping Handle Gear Selection Lever Track Gearbox Gas Spring (Optional) 10 MINI TRACKED DUMPER 09715UK00M112_更新回收处理标志_未发排.
GB Recoil Starter Handle Throttle Control Choke Control Fuel Shut-Off Valve Gear Selection Lever The gear selection lever has 4 positions: 3 forward speeds and 1 reverse. To change speeds, move the speed shift lever to the desired position. The lever locks in a notch at each speed selection. engine will not start or run. ON - engine will start and run. Recoil Starter Handle The recoil starter handle is used to start the engine.
GB Operation IMPORTANT: DO NOT OVERFILL! This equipment and/or its engine may include evaporative emissions control system components, required to meet EPA and/ or CARB regulations, that will only function properly when the fuel tank has been filled to the recommended level. Overfilling may cause permanent damage to evaporative emissions control system components. Filling to the recommended level ensures a vapor gap required to allow for fuel expansion.
CLOSED OPEN The power trackbarrow has a maximum capacity of 660 LBS. However, it is advisable to assess the load and adjust it according to the ground on which the machine will be used. CLOSED OPEN 4. Move the throttle lever slightly to the FAST speed. FAST SLOW 5. Pull the recoil starter until the engine starts. Return the recoil to the home position after each pull. Repeat the steps as needed. Once engine has started, set the throttle to the FAST position before you operate the unit.
GB Sudden stopping at a high speed under a heavy load is not recommended. Engine damage may result. Do not move the choke control to CLOSE to stop the engine. Backfire or engine damage may occur. MAINTENANCE Maintaining your mini tracked dumper will ensure long life to the machine and its components. Adjusting Clutch When the clutch begins to show wear, the handle reach will become wider, making it more difficult to reach. Follow these steps to return the clutch lever back to its original position. 1.
GB Adjustment Nut M8×20 (×4) 1 Belt Cover Jam Nut Jam Nut Lock Nut Lock Nut 2 3 Adjustment Nut M6×20 Jam Nut Belt Cover for Gearbox Pulley Lock Nut If the above adjustment does not create enough cable tension, follow the steps below: Loosen the two bolts M8X25 and one bolt 5/16X30 that fix the two belt blockers, no need to remove them. Pull out the belt. 1. Loosen the jam nut by turning it counter clockwise with 12mm wrench. M8 × 25 2.
GB Gearbox Lubrication The gearbox is pre-lubricated and sealed at the factory. Unless there is evidence of leakage or service has been performed on the gearbox, no additional lubricate should be required until 50 hours use. 3. Measure the track midline vs. the horizontal line. The reading must not be more than 10cm~15cm. After first 50 hours use, change all the gear oil. Capacity is 1.5L. 10cm ~ 15cm For future use, check the oil level after every 50 hours of use.
3. Loosen the adjusting bolts and pull the steering wheel axle toward the engine, then track will be loosen. Steering Wheel GB Steering Wheel Steering Wheel Axle Steering Wheel Axle Do not over-tighten your track. The adjustment of the track and the brakes are linked. The braking power will lessen the more the track is tightened. Adjusting Bolt 4. Pull out the whole track. If the adjustment bolt has no more adjustment left, the tracks may have to be replaced.
STORAGE GB If the mini tracked dumper will not be used for a period longer than 30 days, follow the steps below to prepare your unit for storage. 1. Drain the fuel tank completely. Stored fuel containing ethanol or MTBE can start to go stale in 30 days. Stale fuel has high gum content and can clog the carburetor and restrict fuel flow. 2. Start the engine and allow it to run until it stops. This ensures no fuel is left in the carburetor. Run the engine until it stops.
PARTS SCHEDULE 50 88 GB MINI TRACKED DUMPER 09715UK00M112_更新回收处理标志_未发排.
Gearbox (50) GB 20 MINI TRACKED DUMPER 09715UK00M112_更新回收处理标志_未发排.
PARTS LIST No. Description Q'ty No.
GB 22 No. Description Q'ty No.
No.
Plow Blade (Optional) GB Parts List No. 24 Description Q'ty No.
