ITEM NO.
Carefully read through this entire Instruction Manual before using your XTREMEPOWERUS Power Tool. Take special care to heed the Cautions and Warnings. XTREMEPOWERUS power tool has many features that will make your job faster and easier. Safety, performance, and dependability have given top priority in the development of this tool, making it easy to maintain and operate. GENERAL SAFETY RULES ,&WARNING! Read all safety warnings and all instructions.
IMPORTANT SAFETY INFORMATION GENERAL SAFETY RULES ■ ■ ■ ■ ■ ■ Store idle power tools out of the reach of children and do not allow persons unfamiliar with the power tool or these instructions to operate the power tool. Power tools are dangerous in the hands of untrained users. BATTERY TOOL USE AND CARE ■ Maintain power tools. Check for misalignment or binding of moving parts, breakage of parts and any other condition that may affect the power tool's operation.
IMPORTANT SAFETY INFORMATION ADDITIONAL SAFETY INSTRUCTIONS ■ When using the tool, use safety equipment including safety glasses or shield, ear defenders, and protective clothing including saf ety gloves. Wear a dust mask if the cutting or sanding operation creates dust. If in doubt, do not plug in the tool. Using a power source with a voltage less than the nameplate rating is harmful to the motor. The tool must be used only for its prescribed purpose.
IMPORTANT SAFETY INFORMATION ADDITIONAL SAFETY INSTRUCTIONS FOR THE CHARGER ,A.WARNING! ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ Do not allow any liquid to come into contact with the charger. There is a danger of electric shock. Do not position the tool or battery charger near water; for example, near a sink, wash bowl or toilet. Do not spill liquid of any kind on the tool or charger. Doing so may short out parts, causing damage to the product and creating the risk of fire or electric shock.
IMPORTANT SAFETY INFORMATION ADDITIONAL BATTERYSAFETY INSTRUCTIONS The most suitable temperatures to charge the battery pack are between 20 -25 ° C. ■ Always allow the battery pack to cool down after charging, do not place it in a hot environment such as a metal shed or open trailer left in the sun. ■ Take care where the tool is stored. Do not store in areas of corrosive fumes, or salt air or similar conditions. Try and store the tool in the packaging supplied with the tool.
IMPORTANT SAFETY INFORMATION UNPACKING ■ ■ ■ Unpack all parts and lay them on a flat, stable surface. Remove all packing materials and shipping devices, if applicable. ■ Ensure that you have all the accessories and tools needed for assembly and operation. This also includes suitable personal protective equipment.
2 1 3 4 9 10 5 8 6 7
TECHNICAL DATA SPECIFICATION 100-240V ~ 50/60Hz Charger Battery Lithium-ion 2.0 Ah Charging time around 1 hour No-load speed 0-400 I 0-1500 rpm Torque settings 18 + 1 Max. torque 25N.M. Chuck capacity 10mm keyless chuck Max. drilling capacity for steel 6mm Max. drilling capacity for wood 16mm OPERATING INSTRUCTIONS FOR DRILL DRIVER [I] NOTE: Before using the tool, read the instruction book carefully.
OPERATION 1. ON / OFF SWITCH (SEE FIG. 2) Depress the On/Off switch (8) to start and release it to stop your drill. The on/off switch is fitted with a brake function which stops your chuck immediately when you quickly release the switch.It is also a variable speed switch that delivers higher speed and torque with increased trigger pressure. Speed is controlled by the amount of switch trigger pression.
OPERATION 5. CHUCK ADJUSTMENT (SEE FIG. 6) 7. USING THE LED LIGHT (SEE FIG. 8) To open the chuck (1) jaws rotate the front section of the chuck. Insert the drill bit between the chuck jaws and rotate the front section in the opposite direction. Ensure the drill bit is in the center of the chuck jaws. Finally, firmly rotate the front chuck section in the opposite directions. Your drill bit is now clamped in the chuck. The LED light (9) allows you to keep a clear view under less illuminated circumstances.
OPERATION ■ Overheated: Under the condition above, if the tool does not start, the Battery are overheated. In this situation, let the Tool and Battery cool before pulling the Trigger Switch again. ■ Low battery voltage: The remaining Battery capaci ty is too low and the tool will not operate. In this situation, remove and recharge the Battery. drilled dry. The cutting lubricants that work best are sulfurized cutting oil or lard oil.
Part No. Description 1 M5*22 screw 2 Drilling chuck 3 Torque setting ring 4 Gear box assem. M3*6 screw 5 Motor gear 6 7 550 motor Double speed push button 8 9 Double speed push button spring 10 Double speed push button click spring 11 Click lever 12 Capacity show transparent cover 13 Trigger 14 Contact piece assem. 14-1 Contact shelf 14-2 Contact piece 15 Buckle 16 Battery pack 17 Gear shrapnel 18 LED transparent cover 19 Capacity show plate 20 Magnetic tube 21 Body housing 22 ST2.
14
