MB8.
Table Of Contents Product Registration 1 Important Safety Instructions 2 Important Operation Instructions 3 MB8.5 Assembly Instructions 5 Operation of Your New Indoor Cycle 10 Troubleshooting 16 Manufacturer’s Limited Warranty 17 ATTENTION THIS INDOOR CYCLE IS INTENDED FOR RESIDENTIAL USE ONLY AND IS WARRANTED FOR THE APPLICATION. ANY OTHER APPLICATION VOIDS THIS WARRANTY IN ITS ENTIRETY.
Congratulations On Your New Indoor Cycle and Welcome to the XTERRA Fitness Family! Thank you for your purchase of this quality indoor cycle. Your new indoor cycle has been manufactured by one of the leading fitness manufacturers in the world and is backed by one of the most comprehensive warranties available. XTERRA Fitness will do all we can to make your ownership experience as pleasant as possible for many years to come.
Important Safety Instructions WARNING - Read all instructions before using this appliance. 1. Use this equipment only for its intended use as described in this manual. Do not attempt to ride this bike at high pedal speeds until you have ridden the bike for some time and are comfortable riding at slower pedal speeds. 2. The bike is NOT equipped with a freewheel system which means that when the flywheel is in motion, the pedals will be in motion.
Important Operation Instructions WARNING - AS THE OWNER OF THIS EXERCISE EQUIPMENT, YOU SHOULD INSIST THAT ALL USERS FOLLOW THE SAME GUIDELINES: YOU SHOULD MAKE THIS MANUAL AVAILABLE TO ALL USERS. 1. Obtain a complete physical examination from your medical doctor and enlist a health/ fitness professional’s aid in developing an exercise program suitable for your current health status. 2. When working out for the first time, start out slowly for a minimum of five minutes.
MB8.5 Assembly Pack Checklist Hardware Step 1 #82. 3/8” Nut (4 pcs) #81. 3/8” x 3-1/2” Button Head Socket Bolt (4 pcs) #83. 3/8” x 23mm Curved Washer (4 pcs) Hardware Step 2 #91. M5 x 10mm Screw (2 pcs) Hardware Step 3 #49. 5/16” Split Washer (4 pcs) #48. 5/16” x 16mm Flat Washer (4 pcs) #88. 5/16” x 5/8” Screw (4 pcs) Assembly Tools #85. Wrench MB8.5 Indoor Cycle #86.
MB8.5 Assembly Instructions Pre-Assembly 1. Using a razor knife (Box Cutter) cut the outside, bottom, edge of box along the dotted Line. Lift Box over the unit and unpack. 2. Carefully remove all parts from carton and inspect for any damage or missing parts. If damaged parts are found, or parts are missing, contact your dealer immediately. 3. Locate the hardware package. Remove the tools first. Remove the hardware for each step as needed to avoid confusion.
3 Handlebar Hardware Step 3 #49. 5/16” Split Washer (4 pcs) #48. 5/16” x 16mm Flat Washer (4 pcs) #88. 5/16” x 5/8” Screw (4 pcs) 1. Attach the handlebars (make sure they are oriented as in the illustration) with four Screws (88), four Split Washers (49), and four Flat Washers (48). Tighten firmly using the Combination M5 Allen Wrench & Phillips Head Screw Driver (86). 4 Water Bottle Holder 1. Place the water bottle slightly to the right of center when looking at the bike from the rear. MB8.
5 Left/Right Pedals 25(R) 25(L) 1. Attach the Right and Left pedals to the appropriate crank. The pedals have an “R” and an “L” stamped on the end of the threaded area to distinguish them. Check the illustrations to make sure you are attaching each to the correct side. Note: the left side has left hand threads; therefore you will screw it on in a counterclockwise direction. Tighten each pedal as firmly as possible with the Wrench (85) provided.
6 Console 1 2 3 4 1 – Console 2 – Mounting Clamp 3 – Clamp mounting screw 4 – Clamping thumb screw 5 – Velcro 6 – Speed transmitter 6 MB8.
XTERRA Fitness Indoor Cycling Console Battery Installation: 1. Remove the battery cover from the back of the computer. 2. Insert 2 AAA batteries into the battery compartment and reinstall the battery cover. 3. When Battery working voltage is too low, The “Low battery” indicator will show up on the console display indicating it is time to change the batteries. Speed Sensor Transmitter Battery Installation 1. Remove the battery cover from the transmitter. 2.
Operation of Your Indoor Cycle Getting Familiar with the Control Panel MB8.5 Console PLEASE NOTE: 1. The XTERRA Fitness Indoor Cycling Console system is designed as a sealed unit and not meant to be opened other than for the sole purpose of installing batteries. Any opened units will void the warranty. 2. To clean the XTERRA Fitness Indoor Cycling Console use a clean damp cloth. Use of any caustic cleaning solutions will void the warranty. 3.
Console Operation Time Time is measured in min:sec. There is a time of day clock and a workout timer clock. The workout time will count up or count down during pedaling. If pedaling stops, the time will stop counting after 3sec. RPM/Cadence Cadence is the measurement of how fast the cranks are rotating in RPM. The approximate speed of the bike can also be displayed in MPH or KPH.
Mode Select Press the left hand key to select the SPEED, DIST, TIME or CLOCK at the bottom of the display. Reset/Heart Rate Alarm Select 1. Press the right hand key to activate the heart rate (this will only register if you are wearing the chest strap which is sold separately). If the alarm is on, the alarm icon will flash and a beep will sound to indicate that your heart rate is either above or below the selected target zone. 2.
Heart Rate Target Zones 1. GENDER: Press the left hand key until SPEED is displayed, then press the right hand key for 3 seconds. The TIME will be flashing, press the left hand key until the gender icon is blinking. Press the right hand key to select gender. 2. Press the left hand key to set the measuring value for weight (Lb or Kg); press the right hand key to select. 3. BODYWEIGHT: Press the left hand key to set the bodyweight. Press the right hand key to increase the weight.
First Time User Instructions Adjusting The Bike For A Proper Fit Take some time to learn how to properly adjust the bike to your body; it will make your workouts more pleasant and a safer experience too. Riding the bike when it is incorrectly adjusted can result in discomfort and increase your risk of injury. Adjustment Of Seat Position Seat Height Adjustment 1. Standing next to the bike, adjust the seat until it is about hip height. 2.
Dual Function Pedals Adjusting The Pedal Straps Place your feet in between the aluminum surface of the pedal and the nylon foot strap that wraps around it. If the opening is too narrow, depress the spring loaded clasp with one hand and pull on the nylon strap with the other to increase the opening area. If it is too loose or to tighten the strap, depress the spring loaded clasp, then pull on the open end of the nylon strap until the strap is snug around each foot.
Troubleshooting No Display on Console 1. Hold down any key to bring the console to “Quick Start” mode. 2. Ensure that the batteries are installed properly in the console and transmitter. If they are, install fresh batteries. No Heart Rate signal displayed (chest strap transmitter sold separately) 1. Ensure that your chest strap is worn correctly and that there is moisture under the electrodes. 2.
Manufacturer’s Limited Warranty Effective August 1, 2012 - INDOOR CYCLE LIMITED WARRANTY XTERRA Fitness Inc. warrants all its home use indoor cycle parts for a period of time listed below, from the date of retail sale, as determined by a sales receipt or in the absence of a sales receipt, eighteen (18) months from the original factory shipping date.
3000 Nestle Road Jonesboro, AR 72401 www.xterrafitness.com - Phone:870-336-4286 ©2012 All RIghts Reserved. - Fax:870-935-7611 MB8.
