User's Manual
Table Of Contents
- Important Notice
- Safety and Hazards
- Limitation of Liability
- Patents
- Copyright
- Trademarks
- Contact Information
- Revision History
- 1: Introduction
- 2: Technology Overview
- 3: Standards Compliance
- 4: Electrical Specifications
- 5: RF Specifications
- 6: Power
- 7: Software Interface
- 8: Mechanical and Environmental Specifications
- 9: Regulatory and Industry Approvals
- A: Antenna Specification
- B: Design Checklist
- C: Testing
- D: Packaging
- E: References
- F: Acronyms
- Index
Rev 4 Sep.11 Proprietary and Confidential - Contents subject to change 11
List of Tables
Table 1-1: Supported RF bands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Table 1-2: Required host-module connectors . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Table 3-1: Standards compliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Table 4-1: Connector pin assignments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Table 4-2: Power and ground specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Table 4-3: USB interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Table 4-4: SIM interface signal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Table 4-5: Module control signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Table 4-6: LED states (Default behavior) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Table 4-7: GPIO signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Table 5-1: LTE frequency band support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Table 5-2: LTE bandwidth support. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Table 5-3: CDMA frequency band support . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Table 5-4: Conducted Rx (Receive) sensitivity — LTE bands . . . . . . . . . . . . . . 42
Table 5-5: Conducted Rx (Receive) sensitivity — CDMA bands . . . . . . . . . . . . 42
Table 5-6: Conducted Tx (Transmit) power tolerances . . . . . . . . . . . . . . . . . . . 43
Table 5-7: GPS specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Table 6-1: Averaged standby DC power consumption . . . . . . . . . . . . . . . . . . . 45
Table 6-2: CDMA DC power consumption (+3.3V) . . . . . . . . . . . . . . . . . . . . . . 46
Table 6-3: Averaged call mode DC power consumption (LTE) . . . . . . . . . . . . . 46
Table 6-4: Miscellaneous DC power consumption . . . . . . . . . . . . . . . . . . . . . . 47
Table 6-5: Module power states . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
Table 6-6: Power state transitions (including voltage / temperature trigger levels). .
48
Table 8-1: Mechanical and environmental specifications . . . . . . . . . . . . . . . . . 53
Table A-1: Antenna requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
Table A-2: GPS standalone antenna requirements. . . . . . . . . . . . . . . . . . . . . . 67
Table B-1: Hardware integration design considerations . . . . . . . . . . . . . . . . . . 69