FMC13A ADVANCED LTE TERMINAL WITH FLEXIBLE INPUTS CONFIGURATION Quick Manual v1.
CONTENT Content.................................................................................................................................................................................................................2 Know your device................................................................................................................................................................................................3 Pinout .....................................................................
KNOW YOUR DEVICE TOP VIEW BOTTOM VIEW (WITHOUT COVER) NAVIGATE STATUS LED LED MICRO-SIM SLOT Telematics TOP VIEW (WITHOUT COVER) GNSS ANTENA 2x6 SOCKET BATTERY SOCKET Quick Manual v1.
PINOUT Pin number Pin name Description 1 VCC (10-30) V DC (+) Power supply (10-30 V DC) DOUT 3 Digital output, channel 3. Open collector output. Max. 0,5 A DC 2 DIN 3 / AIN 2 Analog input, channel 2. Input range: 0-30 V DC / Digital input, channel 3 4 DIN 2-N / AIN 1 Digital input, channel 2, Negative input (ground sense), Analog input, channel 1, Input range: 0-30 VDC 5 DIN 1 Digital input, channel 1 3 6 INPUT 6 TX EXT (LVCAN – TX) 7 GND (-) Ground pin.
WIRING SCHEME CAN-CONTROL ALARM BUTTON 87 87a 86 DIN2 AIN2 DIN3 IGNITION DETECTION 85 30 FUEL GAUGE INPUT 6 6 12 INPUT 5 DIN1 5 11 1WIRE DATA DIN2-N/AIN1 4 10 1WIRE POWER DIN3/AIN2 3 9 DOUT2 DOUT3 2 8 DOUT1 +10...30 V DC 1 7 GND IBUTTON DIN2-N ANALOG LLS SENSOR STARTER Telematics BUZZER DOOR SENSOR POWER SUPPLY 10 - 30V DC CENTRAL LOCK Quick Manual v1.
SET UP YOUR DEVICE HOW TO INSERT MICRO-SIM CARD AND CONNECT THE BATTERY 1 2 COVER REMOVAL You will receive your device partly closed. Gently remove top and bottom covers. MICRO-SIM CARD INSERT Insert SIM card as shown with PIN request disabled or read our Wiki1 how to enter it later in Teltonika Configurator2. Make sure that Micro-SIM card cut-off corner is pointing outward from slot. SIM slot 1 is closer to PCB, SIM slot 2 is the top one. 3 BATTERY CONNECTION Connect battery as shown to device.
PC CONNECTION (WINDOWS) 1. Power-up FMC13A with DC voltage (10 – 30 V) power supply using supplied power cable. LED’s should start blinking, see “LED indications”. 2. Connect device to computer using Micro-USB cable or Bluetooth connection: • Using Micro-USB cable • • You will need to install USB drivers, see “How to install USB drivers (Windows)” Using Bluetooth • FMC13A Bluetooth is enabled by default. Turn on Bluetooth on your PC, then select Add Bluetooth or other device > Bluetooth.
CONFIGURATION At first FMC13A device will have default factory settings set. These settings should be changed according to the users needs. Main configuration can be performed via Teltonika Configurator1 software. Get the latest Configurator version from here2. Configurator operates on Microsoft Windows OS and uses prerequisite MS .NET Framework. Make sure you have the correct version installed. 1 wiki.teltonika-gps.com/view/Teltonika_Configurator 2 wiki.teltonika-gps.
Various Status window1 tabs display information about GNSS2, GSM3, I/O4, Maintenance5 and etc. FMC13A has one user editable profile, which can be loaded and saved to the device. After any modification of configuration the changes need to be saved to device using Save to device button. Main buttons offer following functionality: Downloaded Configurator will be in compressed archive. Extract it and launch Configurator.exe.
QUICK SMS CONFIGURATION Default configuration has optimal parameters present to ensure best performance of track quality and data usage. Quickly set up your device by sending this SMS command to it: « setparam 2001:APN;2002:APN_username;2003:APN_password;2004:Domain;2005:Port;2006:0» 1 2 3 4 5 6 Note: Before SMS text, two space symbols should be inserted.
DEFAULT CONFIGURATION SETTINGS MOVEMENT AND IGNITION DETECTION: VEHICLE MOVEMENT will be detected by accelerometer IGNITION WILL BE DETECTED by vehicle power voltage between 13,2 – 30 V DEVICE MAKES A RECORD ON MOVING IF ONE OF THESE EVENTS HAPPEN: 300 seconds passes VEHICLE TURNS 10 degrees DEVICE MAKES A RECORD ON STOP IF: 1 HOUR PASSES while vehicle is stationary and ignition is off VEHICLE DRIVES 100 meters SPEED DIFFERENCE between last coordinate and current position is greater than 10 km/h REC
MOUNTING RECOMMENDATIONS CONNECTING WIRES • Wires should be connected while the module is not plugged in. • Wires should be fastened to stable wires or other non-moving parts. Any heat emitting and/or moving objects should be kept away from the wires. • There should be no exposed wires. If factory isolation was removed while connecting the wires, the isolation material should be applied.
LED INDICATIONS BASIC CHARACTERISTICS NAVIGATION LED INDICATIONS Module Behaviour Meaning Permanently switched GNSS signal is not received on Blinking every second Name FMC13A-QBIB0: Quectel EG91-NA with Teltonika TM2500 Technology LTE(CAT1)/UMTS/GNSS/BLUETOOTH Normal mode, GNSS is working GNSS is turned off because: Off Device is not working or Device is in sleep mode Blinking fast constantly Device firmware is being flashed STATUS LED INDICATIONS Behaviour Meaning Blinking every second
LTE: LTE FDD: Max 10Mbps (DL)/Max 5Mbps (UL) Data transfer Supported peripherals UMTS: WCDMA: Max 384Kbps (DL)/ Max 384 Kbps (UL) Transmit power Data support Class 3 for LTE-FDD: 23±1dBm Class 3 for WCDMA: 23.
Scenarios Green Driving, Over Speeding detection, GNSS Fuel Counter, DOUT Control Via Call, Excessive Idling detection, Immobilizer, iButton Read Notification, Unplug detection, Towing detection, Crash detection, Auto Geofence, Manual Geofence, Trip, Ground Sense Sleep modes GPS Sleep, Online Deep Sleep, Deep Sleep, Ultra Deep Sleep Configuration and firmware update FOTA Web, FOTA, Teltonika Configurator (USB, Bluetooth), FMBT mobile application (Configuration) Operating Environment Operating temperat
Input voltage (Recommended Operating Conditions) ELECTRICAL CHARACTERISTICS Characteristic description Value Supply voltage Min. Supply Voltage (Recommended Operating Conditions) +10 Typ. Max. Unit +30 V Input Voltage threshold (DIN1) 7.5 V Input Voltage threshold (DIN2) 2.5 V Input Voltage threshold (DIN3) 2.5 V Analog input Digital output (open drain grade) Drain current (Digital Output OFF) 120 μA Drain current (Digital Output ON, Recommended Operating Conditions) 0.1 0.
Input resistance, Range 2 150 kΩ Measurement error on 12 V, Range 2 0.9 % Additional error on 12 V, Range 2 108 mV Measurement error on 30 V, Range 2 0.33 % Additional error on 30 V, Range 2 88 mV Output supply voltage 1-wire Supply voltage +4.5 +4.7 V Output inner resistance 7 Ω Output current (Uout > 3.0 V) 30 mA Short circuit current (Uout = 0) 75 mA Negative input Input resistance 38.
SAFETY INFORMATION • Do not disassemble the device. If the device is damaged, the power supply cables are not isolated or he isolation is damaged, DO NOT touch the device before unplugging the power supply. This message contains information on how to operate FMC13A safely. By following these requirements and recommendations, you will avoid dangerous situations. All wireless data transferring devices produce interference that may affect other devices which are laced nearby.
CERTIFICATION This sign on the package means that it is necessary to read the User ‘s Manual before your start using the device. Full User ‘s Manual version can be found in our Wiki1. 1 instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
IC: 28804-FMC13A. IC NOTICE This device complies with Industry Canada licenseexempt RSS standard(s). Operation is subject to the following two conditions: 1. this device may not cause interference, and 2. this device must accept any interference, including interference that may cause undesired operation of the device. This Class B digital apparatus complies with Canadian ICES-003. Cet équipement est conforme aux limites d'exposition aux rayonnements ISED établies pour un environnement non contrôlé.
WARRANTY TELTONIKA guarantees its products to be free of any manufacturing defects for a period of 24 months. With additional agreement we can agree on a different warranty period, for more detailed information please contact our sales manager. Contact us teltonika-iot-group.com/about-us/contacts/ All batteries carry a reduced 6 month warranty period.