CONTENTS Precautions..................................................................................................................1 How to Handle Discs...................................................................................................1 Precautions & Warnings..............................................................................................1 Lithium Battery Cell Warnings.....................................................................................
PRECAUTIONS How to Handle Discs • • • • Handle a disc by its edges. Do not touch the playing side Before inserting a disc, wipe the disc outward from the disc center with a clean, soft, dry and lint-free cloth. Do not use solvents or thinners such a petrol/benzene or cleaners. After removing a disc from the disc slot, place the disc in a sleeve or case to keep it clean and prevent scratches. Do not stick paper or tape on the disc surface.
INSTALLATION Installation Procedures First complete the electrical connections and then check for correctness. Installation Opening This unit can be installed in any dashboard Having an opening as shown the right figure. 103 mm 182 mm Important: Remove the transport CD deck screws before use. To Install the Car Radio Be sure you test all connections first, and then follow these steps to install this unit. 1.
INSTALLATION(CONT.) INSTALLATION DIAGRAM - Only use speakers with 4 ohms impedance. - Do not attach the control panel to the chassis before wiring is complete. - The maximum current of the auto antenna is 200mA. Wiring Connections WIRING DIAGRAM CAUTION +12V DC NEGATIVE GROUND Removal of the Main Unit 1. 2. 3. Remove the metal strap from the main unit. Remove the plastic trim out from the main unit.
CONTROL PANEL BUTTON LOCATIONS B SD 1. (power)/MODE (source) button 2. SEL (select/menu) button and VOL (volume) knob button 3. BAND(band) button , 4. AMS (automatic store / preset station scan, automatic music search) button 5. (pause/play), Preset station1 button 6. INT (intro) , Preset station 2 button 7. RPT (repeat) , Preset station 3 button 8. RDM (random) , Preset station 4 button 9. -10(previous 10 tracks) , Preset station 5 button 10. +10(next 10 tracks) , Preset station 6 button 11.
GENERAL OPERATION Turn Unit On/Off • Press the power ( ) /MODE button on the front panel to turn on the unit, and long press it again to turn off the unit. • Press the power ( ) button on the remote control to turn the unit on or off. Adjust Volume (VOL) Rotate the VOL knob on the front panel or press the VOL+ control to increase or decrease the volume level.
GENERAL OPERATION (CONT.) This function is used for maintaining a program being listened to during a trip if its frequency changes. - TA ON/OFF: Enables or disables the TA function (traffic information). When this function is enabled, the tuner will periodically scan received frequencies and play any traffic information message that may be broadcast. - TA VOL (traffic announcement volume): This function allows you to define the minimum volume for the traffic announcements. The adjustable range is 0~43.
RADIO OPERATION Change Bands (BAND) Press the BAND button to switch between the FM1, FM2 and FM3 band. Each band stores up to six preset stations. Manual Tuning ( / ) Press and hold the or button on the front panel or on the remote control to enter manual tuning mode. In manual tuning mode, press the or button to move the radio frequency number up or down one step.
DISC / USB / MICRO SD CARD OPERATION To insert DISC / USB / SD CARD • To play files on a disc, insert a disc with the label surface facing upward into the disc slot. Playback will begin automatically. Label surface up • To play files in a USB device or an SD card, open the USB port cover and insert the USB storage device into the USB port or an micro SD card into the micro SD card slot. Playback will begin automatically. Eject Disc/USB/Micro SD • To eject a disc, press the button to stop playback.
DISC / USB / MICRO CARD OPERATION (CONT.
BLUETOOTH OPERATION Pair and Connect Prior to using the Bluetooth device as a handsfree system for a Bluetooth-enabled mobile phone for the first time, you must pair and connect the two devices as follows: 1. In any mode, prior to pairing and connecting, the BT logo in the LCD indicating that no device is connected. To begin pairing, enable BT mode on your mobile phone. 2. When the phone the car audio system,the XOMAX XM-2CDB620 name will be displayed. 3.
REMOTE CONTROL Remove Insulating Sheet The remote control comes with an insulating sheet attached to the underside of the remote control, as illustrated on the right. The remote control will not work until the insulating sheet is removed. Replace Lithium Battery Cell 1. When the lithium cell battery becomes weak, replace it as illustrated on the right. 2. Press and hold the movable block in the direction indicated by arrow 1.
SPECIFICATIONS General Chassis Dimensions.............................................................178(W) x 160(D) x 100(H) mm Power Supply Requirement ..................................................................................DC 12V Current Consumption ................................................................................................10A MAXMaximum Power Output ...........................................................................25W x 4CH Radio FM Frequency Range..............
TROUBLESHOOTING The following chart will help in solving most problems that may occur. If you still have questions after going through the checklist, please consult your local customer service representative. Before going through this check list, refer the wiring and operating procedures. Symptom Cause The car ignition switch have not turn on. If the power supply is connected to the car accessory circuits, but the engine is not moving, switch the ignition key to “ACC”. The fuse has been blown.
