UNDERCOUNTER NUGGET ICE MAKERS MODELS: XOUIMN1585NO, XOUIMN1585NOP XOUIMN1585NOADA, XOUIMN1585NOPADA I worked really hard on this manual so please read it...
UNDERCOUNTER When buying any XO appliance you can be confident you have chosen a high quality, innovative and stylish product from a company that cares about you! If you require service or have questions, Help is only a phone call away call: 973-403-8900 Talk to one of our undercounter experts. CONGRATULATIONS on purchasing your XO. Before you proceed, take just a moment to register your XO at: www.xoappliance.
where things are 4 - 7 Before You Get Started Installer Checklist Find Your Model Safet y Instructions Electrical and G rounding Instructions 8 - 19 Installation Inst ruc tions S izes and Installation Dimensions Plumbing With & Without Drain Pump Reversing the Door Door panel Installation O perating I nst ruc tions Features & Specifications Operating Instructions 20 - 22 Ca re and Cl ea nin g Wash Function Cleaning Sanitization Stainless Steel Maintenance Schedule 23 - 28 Trouble Shooting Before You
heres’s ten steps for a quick & easy install 1 Inspect cabinet opening for water, drain and electrical connections. 2 The 1/4” O.D. water supply line must include isolation valve and should include an inline water filter (consult manual). Do NOT use a self-piecing valve for the supply connection. Water supply must have a minimum pressure of 20 psi and a maximum of 80 psi. Cold water o o should be between 50 F and 90 F - NOTE: warmer water will slow ice production. is strongly recommended.
2 these are the models covered in this book INDOOR NUGGET GOURMET ICE MAKER STANDARD HEIGHT XOUIMN1585NO & XOUIMN1585NOP ADA HEIGHT XOUIMN1585NOA & XOUIMN1585NOPA take a minute to circle your model above and record your serial number here in case you need it later 5
your safety matters Pl ease re ad t hrough comp l etely be fore using your XO Unit Periodic maintenance is essential for safe operation - the unit must be easily pulled out for full access. The appliance must be positioned so that the plug and water shutoff are readily accessible. Empty your XO unit before attempting to move the appliance. Moving while loaded may damage or distort the frame. The compressor will get HOT during operation / touching it may cause injury.
Failure To Follow All E l ec trical Safe t y M easures M ay Result in Se rious I nju r y, Fire O r Dea t h All electrical work should only be performed by an experienced, licensed electrician. FOR INDOOR USE: All XO units MUST be grounded for safe operation and come e q u i p p e d w i t h a 3 Prong molded cord/plug for that purpose. NEVER remove or disable the 3rd prong with an adapter. XO Ice Makers shown in this manual are rated for indoor use.
a perfect fit install under counter ALL XO UNDERCOUNTER UNITS ARRIVE PRE-WIRED WITH LOW PROFILE PLUGS FOR EASY INSTALLATION Standard Height Units 33-3/4” MINIMUM (853mm) 7" (178mm) 4" (100mm) 15 ” (381mm) MINIMUM WALL ADA Height Units 31-7/8” MINIMUM (808mm) 90° Door Swing WHEN INSTALLING WITH THE HINGE SIDE NEXT TO A WALL LEAVE ADEQUATE SPACE FOR YOUR DOOR HANDLE DOOR HAS THE ABILITY TO OPEN TO 115 o Clearance Gap When installing, remember you need to leave ready access to both the power Cut acces
a perfect fit your xo is this big ( or small, as the case would be ) height & width XOUIMN1585__ & XOUIMN1565__A ICE MAKER H 33-9/16” STANDARD HEIGHT (853mm) 31-13/16” STANDARD HEIGHT (808mm) 14-7/8” WIDE W (378mm) depth 115 90 TOP VIEW 22-25/32” D (579mm) THE OVERALL DEPTH SHOWN (22-25/32”) INCLUDES THE DOOR WITH 3/4” PANEL.
before you install check a few things Water source tub e 120V Outlet Is the installation location COOL, DRY, LEVEL and away from direct sun. Drain hose The water supply valve must provide positive shut off capability and be readily accessible. Does the unit have a dedicated 115V three prong, properly grounded outlet? o o The Cold Water supply is 1/4” O.D. tube, it should be 50 to 90 F and be between 20 and 80 psi. (NOTE: as the inlet water temperature increases - production efficiency goes down.
water quality All water contains some impurities and minerals. Your XO Ice Maker is designed to produce chewable, nugget ice. It does this by compressing ice flakes as they are forming. PURER WATER YIELDS PURER ICE. Cubes are formed by cold water spraying against a chilled mold. Pure water freezes faster than water containing impurities.
the plumbing Plan the arrangement of the water supply pipes. You will need both a water supply line and a drain (see section on installing a gravity drain unit or pump drain unit) 1/4” O.D. If the tap water has a high level of minerals, an inline filter will be required. Attach the water supply line to the rear of the unit with flexible tube to the fitting indicated here. The tubing must be long enough to permit the unit to be pulled out for service. Water supply should be between 20psi and 80psi.
with gravity drain INSTALLING THE XOUIMN1585 without a drain pump. Position the ice maker in front of the opening. Level the unit using the leveling legs. Wash and flush the water supply tube and connect the unit to the cold water isolation valve. Prepare the drain. The drain must be pitched downward at a drop of 1/4” per foot to drain properly. Horizontal runs of 5’ or more must be anchored to a wall for support to prevent sagging.
with drain pump INSTALLING THE XOUIM1565SP with DRAIN PUMP. Position the ice maker in front of the opening. Level the unit using the leveling legs. Wash and flush the water supply tube and connect the unit to the cold water isolation valve. Cut the 3/8” diameter drain hose to the required length. Immerse the hose in warm water to make installation easier, then connect the drain hose to the drain using hose clamps.
reversing the door Your XO Ice Maker is shipped with the hinge on the right hand side but it can be easily reversed. 1. Remove the inner most screw holding the top and bottom hinges (shown here) 2. Loosen the outer screw holding the top and bottom hinges (as show here) 3. Slide the door and hinges sideways to remove from the cabinet. Hole Plugs 4. On the opposing side of the door, remove the Hole Plugs and screws from the left hand hinge locations. Hinge Pocket Cover 5.
installing the door panel The panel is held in place by self tapping screws and/or machine screws. To install your panel, follow these simple steps: 1. First prepare your custom panel. The panel must be 14-7/8” wide and no more than 3/4” thick. It cannot weigh more than 20 lbs. The height of the panel can vary but cannot block the free exchange of air through the toekick.
Use the upper hole Optional Stainless Steel Panel Use the lower hole MAXIMUM PANEL THICKNESS 3/4” PANEL MAXIMUM WEIGHT: 20 lbs.
overlay panel dimensions xouimn1585no & xouimn1585nop xouimn1585noada & xouimn1585nopada 14-7/8" (378mm) TOP Standard Height 29-13/32” (747mm) ADA Height 27-5/8” (702mm) FRONT PANEL HEIGHTS ARE MINIMUMS, PANEL MAY BE TALLER. PANEL MUST NOT INTERFERE WITH TOEKICK VENTS. AFTER INSTALLATION UNDERCOUNTER DOOR MUST BE ABLE TO OPEN 90o MAXIMUM PANEL THICKNESS 3/4” PANEL MAXIMUM WEIGHT: 20 lbs.
the toekick PANELS MAY EXTEND HIGHER OR LOWER THAN THE DOOR BUT MUST NOT OBSTRUCT THE FREE EXCHANGE OF AIR THROUGH THE TOEKICK.
2 features & specs Produces up to 85lbs of nugget ice per day Stores 24.
operation You XO Ice Maker is simple to operate. When you open the door you will see the electronic button/display located at the top center of the appliance. The first button, LAMP, allows you to cycle through the 5 different interior LED Light colors (white, Dark Blue, Green, Red and Light Blue). The ICE light will always come on first when the unit is switched on. Initially, the unit will automatically fill and drain water three times then, the ice making cycle will begin.
operation cont. DURING OPERATION: After turning the switch to the ICE position, ice production will begin and continue until the ice bin has been filled. Once the bin is filled, production will automatically be paused. Remove ice using the handy scoop located in a holder in the top left hand side of the interior. It takes approximatel 10 hours to fill the ice bin, this time may vary based on ambient and water temperatures. W 0.6” NUGGET ICE: Nugget ice is a smaller softer cube H 0.
maintenance Proper maintenance, cleaning and santizing is essential to ensure your ice is safe, fresh and odor free. WASH FEATURE: Regular maintenance is the key to delicious, wholesome ice. The WASH feature helps make this easy to perform. When the WASH Position of the switch is selected, the cleaning process takes approximately 10 minutes and the following action take place: BEFORE BEGINNING - REMOVE ALL ICE FROM THE ICE BIN. 1.
maintenance cont. Proper maintenance, cleaning and santizing is essential to ensure your ice is safe, fresh and odor free. CLEANING: BEFORE BEGINNING - REMOVE ALL ICE FROM THE ICE BIN. 1. Prepare by mixing 0.25ℓ of a non-toxic, nickle-safe Ice Maker cleaning solution and 5ℓ of water. 2. Open the door and pour approximately 1 liter of cleaning solution into the ice spout located at the top, rear of the unit. 3. Toggle the lower front mode switch to “WASH”.
maintenance cont. Proper maintenance, cleaning and santizing is essential to ensure your ice is safe, fresh and odor free. SANITIZING: BEFORE BEGINNING - REMOVE ALL ICE FROM THE ICE BIN. 1. Prepare by mixing 0.25ℓ of a Ice Maker sanitizer solution and 5ℓ of water. WARNING: Observe all safety precautions including the use of protective eyewear and gloves while using sanitizer. Read and observe all manufacturers instructions carefully. 2.
stainless steel cleaning the exterior Stainless Steel: Stainless steel does not stain, corrode, or rust as easily as ordinary steel, but it is not stain or corrosion proof. Stainless steels can discolor or corrode if not maintained properly. Stainless steels differ from ordinary carbon steels by the amount metals such as chromium and nickel used in the alloy. It is the chromium which provides an invisible protective film on the surface called chromium oxide.
the condenser improve efficiency & performance Cleaning the condenser Remove dust and dirt from the surface of the condenser coils with a vacuum cleaner Remove two screws on the front panel at the center of the inside Vacuum the condenser coils Reassemble the panel using the two screws to after cleaning 27
maintenance schedule o The following maintenance schedule is a guideline. Maintenance and repairs should be performed more frequently where required by water quality, equipment usage and local hygiene regulations. FREQUENCY AREA TASK DAILY Scoop Clean with neutral cleaner / rinse thoroughly MONTHLY Water filter Check dressure drop / change as needed Exterior of unit Wipe down with clean soft cloth. Use neutral cleaner on damp cloth to remove oils or dirt.
what the control lights mean PROBLEM ICE NO WATER DRAIN POSSIBLE CAUSE ACTION Making Ice O Switch in “ICE” position Washing B Switch in “WASH” position ICE lamp blinks once per second Switch in “WASH” position ICE lamp blinks once per second Bin Full B ICE lamp blinks every 2 seconds Will turn off when sensor detects release temperature O Draining B Water Supply Error Drain Error Evap Temp Error B Evap Temp Error B B B Ice Full Sensor Error Evap Temp Sensor B Air Temp Sensor Error
troubleshooting PROBLEM POSSIBLE CAUSE ACTION Ice maker not operating No power Unit unplugger / plug in Breaker thrown / rest breaker Switch in wrong position Change switch to ICE position Storage bin full Operating normally - production ceases when bin is full Room temp below 50 o / raise room temp.
we’ve got your back 90 DAY LOVE IT or LEAVE IT. For 90 Days all our products are backed by our unique Love it or Leave it Guarantee. ONE-YEAR PARTS & LABOR LIMITED WARRANTY. XO warrants to the original purchaser of every new XO ice maker unit, the cabinet and all parts thereof, to be free from defects in material or workmanship under normal and proper use and maintenance as specified by XO and upon proper installation and start-up in accordance with the instruction packet supplied with each XO unit.
SEE ALL THE LATEST XO PRODUCTS AND ACCESS PARTS AT: WWW.XOAPPLIANCE.
