User's Manual

1. This device complies with Part 15 of the
FCC Rules. Operation is subject to the
following two conditions:
(1) This device may not cause harmful
interference.
(2) This device must accept any interference
received, including interference that may
cause undesired operation.
2. Changes or modifications not expressly
approved by the party responsible for
compliance could void the user's authority
to operate the equipment.
NOTE:
This equipment has been tested and found
to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide
reasonable protection against harmful
interference in a residential installation.
This equipment generates uses and can
radiate radio frequency energy and, if not
installed and used in accordance with the
instructions, may cause harmful
interference to radio communications.
However, there is no guarantee that
interference will not occur in a particular
installation. If this equipment does cause
harmful interference to radio or television
reception, which can be determined by
turning the equipment off and on, the user
is encouraged to try to correct the
interference by one or more of the following
measures:
Reorient or relocate the receiving antenna.
Increase the separation between the
equipment and receiver.
Connect the equipment into an outlet on a
circuit different from that to which the
receiver is connected.
Consult the dealer or an experienced
radio/TV technician for help.
SAR Information Statement
Your wireless phone is a radio transmitter
and receiver. It is designed and
manufactured not to exceed the emission
limits for exposure to radiofrequency (RF)
energy set by the Federal Communications
Commission of the U.S. Government. These
limits are part of comprehensive guidelines
and establish permitted levels of RF energy
for the general population. The guidelines
are based on standards that were
developed by independent scientific
organizations through periodic and
thorough evaluation of scientific studies.
The standards include a substantial safety
margin designed to assure the safety of all
persons, regardless of age and health. The
exposure standard for wireless mobile
phones employs a unit of measurement
known as the Specific Absorption Rate, or
SAR. The SAR limit set by the FCC is 1.6
W/kg. * Tests for SAR are conducted with
the phone transmitting at its highest
certified power level in all tested frequency
bands. Although the SAR is determined at
the highest certified power level, the actual
SAR level of the phone while operating can
be well below the maximum value. This is
because the phone is designed to operate at
multiple power levels so as to use only the
power required to reach the network. In
general, the closer you are to a wireless
base station antenna, the lower the power
output. Before a phone model is available
for sale to the public, it must be tested and
certified to the FCC that it does not exceed
the limit established by the government
adopted requirement for safe exposure. The
tests are performed in positions and
locations (e.g., at the ear and worn on the
body) as required by the FCC for each model.
The highest SAR value for this model phone
when tested for use at the ear is0.219W/Kg
and when worn on the body, as described in
this user guide, is 1.193
W/Kg(Body-worn measurements differ
among phone models, depending upon
available accessories and FCC requirements).
The FCC has granted an Equipment
Authorization for this model phone with all
reported SAR levels evaluated as in
compliance with the FCC RFexposure
guidelines. SAR information on this model
phone is on file with the FCC and can be
found under the Display Grant section of
http://www.fcc.gov/ oet/fccid after
searching on
FCC ID:2ABOSSKYPLATB7 Additional
information on Specific Absorption Rates
(SAR) can be found on the Cellular
Telecommunications Industry Asso-ciation
(CTIA) web-site at
http://www.wow-com.com. * In the United
States and Canada, the SAR limit for mobile
phones used by the public is 1.6 watts/kg
(W/kg) averaged over one gram of tissue.
The standard incorporates a sub-stantial
margin of safety to give additional
protection for the public and to account for
any variations in measurements.
Body-worn Operation
This device was tested for typical
body-worn operations. To comply with
RF exposure requirements, a minimum
separation distance of 10mm must be
maintained between the user’s body
and the handset, including the antenna.
Third-party belt-clips, holsters, and
similar accessories used by this
device should not contain any metallic
components. Body-worn accessories
that do not meet these requirements may
not comply with RF exposure
requirements and should be avoided.
Use only the supplied or an approved
antenna.