Universal High Power Auto-Focus Digital SLR Flash wide angle diffuser & reflection board Item # XTDF260 INSTRUCTION MANUAL designed for D-SLR
Warning 1. To avoid fire or electrical shock,do not expose this product to rain or moisture. 2. Do not flash at hight level output continuously for over 15 time. 3. To avoid short circuit,be sure the batteries contacts are securely packed and in accordance with local provisinon when handling the batteries. 4. Please place the batteries and the parts which can be swallowed mistakenly away from children. Contact a doctor immediately when it occurs. 5.
Features * Wireless triggering sensor: It can works in outdoor environment under S1 and S2 mode, the wireless triggering distance is up to 10-15M in outdoor, 20-30m in indoor. * Super speed of charging recycle: It only takes 4 seconds in charging * The improved power saving mode: In the power saving mode,the flash will get automatic sleeping.
Nomenclature 1.Reflection board 2 2.Wide-angle diffuser 1 3 3.Flash head 4. Wireless sensor 5.Battery compartment cover 6.Hot shoe stand 5 4 6 7.Fixed dial 8.Contacts 7 9.
Nomenclature M 9 S1 S2 10 11 ZOOM PILOT 24 28 35 MODE 12 50 70 ZOOM 85 mm ON/OFF 15 16 13 17 14 18 -4-
Nomenclature 10. Mode indicator(M,S1 and S2): It indicateds the current flash mode. 11. Output level indicator: It can regulate the output power by setting the button, there are 8 levels for output level adjustment. It indicates the output power and the fine-turning; it indicates the coverage of the current focus length when adjusting the focus length 12. Test button 13. Mode switch button: The mode of the flash ligth will be switched among the M/S1/S2 in circle for each press. 14.
Installation Instruction 1. Install Batteries Slide the batteries chamber’s cover in the direction of the arrow. Insert the batteries according to the label inside battery chamber.Make sure the direction of the batteries’ polarity is correct. Close the battery chamber cover in the direction of the arrow.
2. Mount the speedlite on your camera a. Loosen the locking ring by turning it in the direction of the arrow. b. Slide the speedlite hot shoe stand into the camera hot shoe stand until it stops. Turn the locking ring in the direction of the arrow tighten. c. To detach the speedlite,loosen the locking ring by turning it in the opposite direction.
Basic functions 1.Basic Operations Operation of the buttons: Operation Component Power and focus adjustment and button Power fine adjust button button Power Switch of the flash light.The power of the flash light can be opened or closed by holding this button for 2 seconds.It is suggested that the battery shall be taken out after the power of the flash light is closed through this button.
Meaning of ： Meaning of(Output control indicator) represents state of indicator’s light. While O represents state. State In M/S1/S2 Mode,indicates the output level State of
2. Turn ON/OFF: *The power of the flash ligth can be opened or close by holding this button for 2 seconds. It is suggested that the battery shall be taken out after the power of the flash ligth is closed throught this button. *After opening the power switch of the flash,the flash will fetch the setting state saved in the close down last time,the charging indicator is green,which indicates the flash is avallable. *If the charging is not completed within 20 seconds, shortage of power supply can not to flash.
4. S1/S2modes By pressing the ,the flash will step into the S1/S2 mode.These two modes are suitable to be used as off -camera auxiliary light,so as to create a variety of lighting effects.They aresuitable for manual flash environment and Ttl flash environment respectively. *Under these two modes,the way to adjust the output level is like that in M mode,which is to press the and in the middle.
6. Flash will eningy power save mode : if 30s have any operation, It can be wake up through any button 7. Overheating proteciton If the flash light is used too frequently,its overheating protection funciton will be triggered, the red and green lights of the charging indicator will blink alternatively,and the flash light will be locked. in such case, wait indicator to be green then cancel the protection before continuing the use.
8. Manually set the zooming position By pressing ZOOM ,you can set the zooming position, zoom will chang green light when focus adjust status. Pressing < >and < >.the covered focus lenght of the flash will switch of (24/28/35/50/70/85mm).In setting the flash zooming position.the indicator in the operational panel will indicate the currentposition.The focus length showed by the displayed position can be found in the table below. represents state of indicator’s light,while representsstate.
The Advanced Application 1. Output power fine adjust function: Press the "SET" button, Among two power indicator lights up , through the left and right key for fine-tuning, every time fine-tuning value one third, When make sure the parameters, then press key again can save and quit, or after 15 seconds later Automatic save and exit.
2. Multi-flash Lighting Application Use inbuilt flash or top-mounted flash as master flash, Place ulti-speedlite in different directions. *In indoor application,radio signals can be reflected by walls;therefore,the placement of the slave flash should have more space. Wrieless triggering distance is up to 20-30M. *which can be avaiable in outdoor state.
3. Reflection Flash Bounce flash means to take photos by making flash light head aimed at will or ceiling and using the light reflected back from the ceiling or wall to light the desired object,so that the shade behind the object can be decreased to ger more natural shooting effect. If the wall or ceiling is too far,the bounce flash may be too weak to get enough exposure.
5. Use Wide-angle Diffuser Pull out the wide-angle diffusion board,push back the reflection board and arrange them as per the figure; Iin such case,the flash scopes will extent to 18 mm and the flash effect will be softer and more natural.
Specifications Guide Number Flash mode Vertical rotation angle Horizontal rotation angle Power supply Lighting times Recycle time Color temperature Flash time Flash control External interface Wireless triggering distance Additional features Dimensions Net weight ccessories 85 meters (ISO 100,85mm) M,S1,S2 0-90 degrees 0-270 degrees 4XAA size batteries(Alkaline or Ni-MH are usable) 100-1500 times(AA alkaline cell used) approx 4s 5600k 1/500s-1/20000s 8 levels of output control(1/128-1/1), every level have s
Guide number of different focus length range GN85 ISO 100 (meters / feet) Flash output Coverage(MM) 24 28 1/1 20/66 22/72.6 1/2 12.2/40.1 15.3/45.9 1/4 8.8/28.9 11/36.1 1/8 6.3/20.7 35 50 25/82 27/88.6 17.7/58.1 12.5/41 70 30/98.3 19.1/62.7 21.9/71.9 13.5/44.3 15.5/50.9 85 33/109.2 105 36/118.1 24/87.7 26.2/86 17/55.8 18.5/60.7 7.8/25.6 8.8/28.9 9.5/31.2 11/36.1 12/39.4 13.1/43 1/16 4.4/14.4 5.5/18 6.3/20.7 6.8/22.3 7.8/25.6 8.5/27.9 9.3/30.5 1/32 3.1/10.2 3.9/12.
Possible problems during use and solutions 1.Please note when use the flash outdoors:For outdoor application,please avoid direct sunlight to the wirless triggering sensor and ensure normanl use of the falsh. 2.Precaution for outdoor sue of lambency umbrella; The lambency umbrella mounted on the falsh light outdoors may be blowen down easily ,and the hot shoe of the flash light may be broken. Please fix the mounting rack or avoid outdoor use. 3.
