Bosch Connected Control BCC50 Thermostat User Guide T E MOS GET TH UR NEW O Y F OUT O MOSTAT THER Bosch ad The Downlo Control App ted Connec GE XX SEE PA FO ORE IN FOR M BoschHeatingAndCooling.
Table of Contents Meet the Bosch Connected Control (BCC50 Thermostat) The Bosch Connected Control BCC50 Thermostat is compatible with the majority of 24VAC heating and cooling equipment to 1 Compatibility Device Settings 2 Thermostat Install 14 Screen buttons, the Bosch Connected Control smartphone app or your voice with the Bosch Connected Control Alexa Smart Home Skill 3 Initial Setup 15 Date & Time and your Alexa-enabled smart devices or with google assistant.
Compatibility u u A C-wire (common wire) is required to power the unit. Two wire systems are not supported. If a C-wire is not readily available, we recommend you seek professional support from your local contractor. The Bosch Connected Control BCC50 Thermostat works with most 24VAC systems, including gas, oil, propane, electric, forced air, variable speed, heat pump and radiant.
Thermostat Install Step 2 Turn OFF Power Remove the old thermostat from the old wall plate Turn off the power to your HVAC (Heating, Ventilation, and Air Conditioning) system by using the master equipment switch or circuit breaker box. ON OFF Take a Picture of The Existing Wiring Make sure that you can clearly read the terminal labels and see which wires are connected to which terminal from your photo. You will need to reference this photo later during the initial setup.
Thermostat Install Pull Thermostat Wires Through The Hole in the Center of the BCC50 Wall Plate and Mark the Location of the Mounting Screws It is recommended to use the BCC50 Wall Plate as a reference guide to mark the mounting holes and ensure that all holes and unpainted surfaces are covered. If the new Wall Plate does not cover up any holes or unpainted spaces left by your old thermostat, use this opportunity to patch any holes or paint.
Thermostat Install Step 13 Step 12 Turn ON the Power to Your HVAC by Using the Master Equipment Switch or Circuit Breaker box. The thermostat will power on and display a Bosch logo and loading bar. Note: After loading completes, the thermostat will display the following screen: Great Job, The Hard Parts Over! ON OFF Next get Your Smartphone and Visit Your App Store. Download the Bosch Connected Control app to Set-up Your New BCC50.
Initial Setup Unit Configuration Select your Heat Type according to the heating appliance located in your home. Below is a list of helpful tips that may guide you to selecting the correct option for your home. Note: If you are unsure of which option to select, contact your local contractor or our support line: 1-800-283-3787. If you Have a Dual Fuel System 1. Select Dual Fuel and click the setup button to the right 2.
Initial Setup Date & Time Follow the on-screen instructions to set the date and time of BCC50 Thermostat and then click Next. 7. After you have set up one day of the week, use the Copy section to mirror the same daily schedule to other days of the week by clicking on the days you would like to copy that daily set of periods. Then click next.
Advanced Settings Advanced Settings Advanced Settings allow HVAC professionals the ability to modify specific thermostat Heating & Cooling uuTo access the Hveating and Cooling, click Heat – Cool on the Advanced Settings screen and enter the Professional Access Code. uuClick on a setting and use the scroll wheel to modify the default value. From this menu you can adjust: settings for better control of the heating and cooling appliance(s).
Advanced Settings Installer Access uuTo access the Installer Access, click Installer on the Advanced Settings screen and enter the Professional Access Code. uuEnter any one of the Action Codes in parenthesis below to gain access to that specific setting: Humidity Calibration (HC) Ability to adjust humidity readings to improve sensor accuracy as the thermostat nears the end of its lifecycle after years of use.
Advanced Settings Troubleshooting Device Log uuTo access the Device Log, click Log on the Advanced Settings screen and enter the Professional Access Code. uuThe Device Log stores up to 90 days’ worth of thermostat activity. To view historical data, select the time period you would like to view.
Wiring Diagrams ---Single Stage Heat – Furnace Ensure the system has a C-wire Ensure the pre-installed jumper wire remains between RH and RC Connect the R, C, W1 and G wires from the Furnace to RH, C, W/E and G terminals on the wall plate, respectively G C W2/ AUX W/E Y Y2 O/B RH Jumper ---- Ensure the system has a C-wire Ensure the pre-installed jumper wire remains between RH and RC Connect the R, C, W1, W2 and G wires from the Furnace to RH, C, W/E, W2/ AUX and G terminals on the wall plate, resp
Wiring Diagrams ---Single Stage Heat Pump Ensure the system has a C-wire Ensure the pre-installed jumper wire remains between RH and RC Connect the R, C, Y1, O/B and G wires from the heat pump to RC, C, Y, O/B and G terminals on the wall plate, respectively Data G C W2/ AUX Y2 O/B Two Stage Heat Pump with One Stage Emergency Heat Ensure the system has a C-wire W/E Ensure the pre-installed jumper wire remains between RH and RC Y Connect the R, C, W1, Y1, Y2, O/B and G wires from the heat pump to R
Wiring Diagrams Combined Single Stage Heat and Single Stage Cool Furnace and Air Conditioner Ensure the system has a C-wire Remove the pre-installed jumper wire from between RH and RC Connect the R, C, W1 and G wires from the Furnace to RH, C, W/E and G terminals on the wall plate, respectively Connect the R, C, Y1 and G wires from the Air Conditioner to RC, C, Y and G terminals on the wall plate, respectively Humidifier or Dehumidifier Accessory with a Single Stage Heat Pump Note: The wiring configuratio
User Manual How to use your BCC50 Thermostat Use the illuminated buttons to navigate the thermostat. If you do not see the illuminated buttons, simply click on a button’s location to illuminate all the lights. Note: the screen is not a touch screen. The buttons are the only way to interact with the device. The buttons will turn off after a few seconds of no use.
Adjusting Temperature Setpoint(s) No Schedule From the Main Screen, use the up or down arrows to change the temperature setpoint, and then press Ok to confirm your selection. You will see a green check mark confirming your selection. Menu Overview Schedule Follow the same process as above to change the setpoint, but be aware that you are only changing the setpoint until the next scheduled period listed on the thermostat.
Menu Overview Accessory Use the up and down arrows to change the relative humidity setpoint, and then press Ok to confirm your selection. You will see a green check mark confirming your selection. Note: this item will not appear on your thermostat if you did not setup a humidifier or dehumidifier accessory during the initial setup process. 32 Menu Overview Wi-Fi Use the up and down arrows to Connect, Re-Connect or Disconnect from your home’s Wi-Fi network.
Bosch Connected Control App Menu Overview The app allows you to remotely control all of your thermostat’s settings. It also allows you to adjust your schedule on-the-go or set it to vacation mode to save energy while you’re away. You can also connect an unlimited number of thermostats and manage up to 4 schedules per thermostat. This is a perfect solution to help you achieve maximum comfort with minimum effort! Downlo ad Today! Control all of yo thermos ur tat’s your sche settings.
App Adjusting Temperature Setpoint(s) Need Screen 36 Main Screen Overview Actual Room Temperature Current Schedule Period Current Time Heating Setpoint Cooling Setpoint Actual Room Relative Humidity Lock Refresh / Sync Time Mode Menu No Schedule From the Main Screen, tap the current temperature and use your finger to scroll up or down to change the temperature setpoint. Stop on the value you want for your new setpoint and wait a few seconds for the setpoint to update.
App Menu Overview Need Screen Schedule uuTo add a new Schedule, use the ‘+’ button in the top right hand corner, name your schedule and click OK. uuTo modify an existing Schedule, select a Schedule from the list and click Next. 38 App Menu Overview Need Screen Add a New Period To add a new Period to a given day, click the Add Period button in the middle of the screen and then individually select and set Starting time, Heat setpoint and Cool setpoint.
App Menu Overview Need Screen Need Screen Need Screen Need Screen Need Screen Wi-Fi space for text Mode Similar to the BCC50 Thermostat, use the Mode screens to adjust remotely the System Mode, Fan Mode and Accessory Mode. 40 Wi-Fi To change the Wi-Fi Network that your thermostat uses to connect to the internet, follow the on-screen instructions on your app. Note: ensure that you have clicked Connect from your Thermostat’s Wi-Fi menu to start the pairing process.
Additional Features Connecting Your BCC50 to Amazon Alexa Control Your BCC50 with Amazon Alexa Bosch offers one Smart Home Skill for integrating your BCC50 with Amazon Alexa’s voice controls. Using the Bosch Connected Control Skill from the Skills section of the Amazon Alexa App. You Can Control the BCC50 by Saying: ▶▶ Alexa, turn (Device Name) on. ▶▶ Alexa, turn (Device Name) off. ▶▶ Alexa, Increase (Device Name) by _ _ degrees. ▶▶ Alexa, Decrease (Device Name) by _ _ degrees.
Additional Features Need Document Control Your BCC50 with Google Assistant Bosch offers one Smart Home Skill for integrating your BCC50 with Amazon Alexa’s voice controls. Using the Bosch Connected Control Skill from the Skills section of the Amazon Alexa App. You Can Control the BCC50 by Saying: ▶▶ Alexa, turn (Device Name) on. ▶▶ Alexa, turn (Device Name) off. ▶▶ Alexa, Increase (Device Name) by _ _ degrees. ▶▶ Alexa, Decrease (Device Name) by _ _ degrees. ▶▶ Alexa, Set (Device Name) to _ _ degrees.
Warranty This limited warranty is provided by Bosch Thermotechnology Corp. (“Bosch”) and covers the Bosch Connected Control (BCC50) Wi-Fi Thermostat (hereinafter referred to as “Product”). This warranty is provided to the original purchaser of the Product as long as the Product remains installed at its original place of installation.
Bosch Thermotechnology Corp. Watertown, MA • Londonderry, NH • Ft. Lauderdale, FL General Inquiries: 1-866-330-2725 www.boschheatingandcooling.com 70H995260B 1/19 Copyright © 2019 Bosch Thermotechnology Corp. All rights reserved. Subject to change without notice.
FCC Caution This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
IC Caution: This device complies with Industry Canada’s licence-exempt RSSs. Operation is subject to the following two conditions: (1) This device may not cause interference; and (2) This device must accept any interference, including interference that may cause undesired operation of the device. To maintain compliance with RF exposure guidelines, this equipment should be installed and operated with a minimum distance of 20cm between the radiator and your body.
