Instruction Manual

INSTALLATION INSTRUCTION FOR
CEILING FAN REMOTE CONTROLLER
MODEL NO. OF RECEIVER: AA2022-8RF-S3L1, AA2022-8RF-S4L1, AA2022-8RF-S6L1,
AA2022-8RF-S3L2, AA2022-8RF-S4L2, AA2022-8RF-S6L2,
AA2023-1RF-S3L1, AA2023-1RF-S4L1, AA2023-1RF-S6L1,
AA2023-1RF-S3L2, AA2023-1RF-S4L2, AA2023-1RF-S6L2
MODEL NO. OF TRANSMITTER: HTT20085XX
IMPORTANT POINTS:
1. Please read this instruction, and save it for further use.
2. Before installation, TURN OFF THE POWER OF YOUR CEILING FAN.
3. Please note that all wiring appliances should be installed by a qualified electrician.
4. This unit is to be used in a 100-120V~ 50/60Hz supply only. (Rating: RECEIVER: Max
100W and Min 15W for fan motor, Max 100W for each lamp. TRANSMITTER: transmitting
frequency range: 433.92MHz±300kHz, Maximum transmitting power: 8dBm.)
5. Do not install in damp locations or immerse in water. (For indoor use only.)
6. Do not pull on or cut leads shorter.
7. Do not drop or bump the unit.
8. PLEASE NOTE: The battery will weaken with age and should be replaced before leaking
takes place as this will damage the transmitter.
9. The batteries must be removed from the transmitter before it is scrapped. And the batteries
shall be disposed of safety.
10. The switch shall be mounted at a height greater than 1.7m.
11. The electric shock protection of the RF receiver shall be depended on its installation.
12. The RF remote controller shall be used within its rating range, otherwise overheating and
dangerous phenomenon may occur.
13. The RF ceiling fan remote controller is made by XIN HUI A.A. ELECTRONICS LTD.
14. CAUTON: To reduce the risk of fire or injury, do not use this product in conjunction with
any variable (rheostat) wall control.
15. Warning: Changes or modifications to this unit not expressly approved by the party
responsible for compliance could void the user’s authority to operate the equipment.
16. This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) this device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause undesired operation.
17. NOTE: This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. This limits are designed to provide
reasonable protection against harmful interference in a residential installation. This equipment
generates uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
□ Reorient or relocate the receiving antenna.
□ Increase the separation between the equipment and receiver.
□ Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
□ Consult the dealer or an experienced radio/TV technician for help.
CONTROL INSTRUCTIONS:
1. The receiver is only control by transmitter.
2. If you would like to operate receiver by a new transmitter, you must use the transmitter to
code the remote controller.
3. The way of code is within 60s after the receiver is powered on, you should press and hold
on the key of FAN OFF for 5s to code. If code successfully, you will hear a sound “beep”
from buzzer or you will see the led twinkles 1-3 times.
4. After code successfully, the new transmitter can control the receiver and the old transmitter
can not control the receiver.
FUNCTIONS OF RECEIVER AND TRANSMITTER:
AA2022-8RF-SXLY
①
represents fan speed level and can be replaced by 3, 4, 6.
3 means the product can control the fan speed level is 3.
4 means the product can control the fan speed level is 4.
6 means the product can control the fan speed level is 6.
②
represents the number of led and can be replaced by 1, 2.
1 means the product can control the number of led is 1 independently.
2 means the product can control the number of led is 2 independently.
①
②
1h 3h 6h 8h
FAN ON/OFF: Turn on or turn off ceiling fan.
SPEED UP: Rise the ceiling fan speed 1 level.
SPEED DOWN: Reduce the ceiling fan speed
1 level.
LIGHT ON/OFF: Turn on or turn off the light.
TURN COLOR: Turn the led color.
(Only for the specific led.)
: The led and ceiling fan will turn off after 1
hours.
: The led and ceiling fan will turn off after 3
hours.
: The led and ceiling fan will turn off after 6
hours.
: The led and ceiling fan will turn off after 8
hours.
1h
3h
6h
8h