Inc. Trainers/Controllers Instructions Manual

76
ELECTRONIX EXPRESS / RSR • 365 Blair Road, Avenel, NJ 07001
77
Call Toll Free: 1 [phone] • In NJ: [phone]
• Fax:
[phone]
[phone]
Back to Catalog Download Main Page (http://www.elexp.com/a_print.htm)
Back to Catalog Download Main Page (http://www.elexp.com/a_print.htm)
BLUETOOTH BOARD
This board allows you to add Bluetooth capability to any
microcontroller with UART functionality.
E-BLOCK™ SYSTEM
The E-Block™ System consists of small circuit boards each of which contains electronics that you would typically nd in an
Electronic System. The E-Blocks™ range consists of around 150 separate items which can be combined to make a variety of
systems offering a wide range of learning opportunities. Select a Programmer Board, add a number of peripheral boards,
combine with a range of software utilities including “Flow Code” to develop a fully functional electronic system.
PROGRAMMING BOARDS
PICMICRO DEVELOPMENT BOARD VER. 3
This is an ideal platform for
learning how PICmicros are
programmed and also for project
work. This board programs a
range of 8, 14, 18, 28 and 40
pin devices from the 12, 16 and
18 series PIC micro ranges. The
on-board LED’s, switches and displays can be used in CD
ROM based courses or with Microchip’s MPLAB software. The
board also has two E-Blocks parts (on ports C and D) which
makes it compatible with a large range of E-blocks add-ons
and sensors.
Features:
• USB Connector
• Single bit audio output
• 2 line LCD display
• Onboard sensors
• Quad 7 segment displays
PICMICRO MULTIPROGRAMMER
This programmer connects to your PC via
USB to provide you with a low cost and
exible PIC microcontroller programmer.
This board can be used with Assembly,
C or Flowcode programming utilities
provided by Matrix Multimedia. This board
will programm most 8, 14, 18, 28 and
40 pin ash PIC micro devices using the
exible programming software provided and
provided “clean” access to all I/O lines. The
board has 5 E-blocks parts to which you can connect a
variety of peripheral boards.
LED BOARD
It has 8 LEDs which shows the status of each bit on
the port
LCD BOARD
This E-block contains a 16 character 2 line alphanu-
meric LCD display on a 5 wire serial bus.
SWITCH BOARD
This E-block contains 8 push-to-make switches. Connec-
tors allow this board to be used in bus conguration.
PROTOTYPE BOARD
It contains a small breadboard for developing circuits
and projects. Connectors for two E-block ports allow
prototype wires and leads to be connected to the rows
and columns on the prototype board.
SENSOR BOARD
This board contains a variable resistor and a simple
light sensor which can be used for simple analog ex-
periments. It also contains sockets which allow users to
interface with many other sensors.
INTERNET BOARD
This board adds Ethernet functionality to a microproces-
sor with the need for developing a TCP-IP software stack.
VOICE CODEC BOARD
This audio coder-decoder board allows students to inves-
tigate Bluetooth systems that use audio. It is based on
MC145483 linear 13 bit CODEC which allows voice digiti-
zation and reconstruction as well as pre and post ltering.
MOTORS BOARD
This board is based on L298 device which can drive
two motors operating up to 46 V @ 4A each. It can be
used in a variety of motor control congurations includ-
ing PID control.
KEYPAD BOARD
A simple 4 x 3 keyboard that allows data entry into bus
based systems.
Part No. Description Price
01EB004 LED Board $22.00
01EB005 LCD Board 32.00
01EB007 Switch Board 22.00
01EB016 Prototype Board 32.00
01EB003 Sensor Board 26.00
01EB024 Bluetooth Board 210.00
Part No. 01HP488 • Price: $285.00
Part No. 01EB006 • Price: $115.00
FLOWCODE / PICMICRO
PLATFORM WIN95/98/ME/NT/2000/XP
Flowcode is a very high level language
programming system for PICmicro® micro-
controllers based on owcharts. Flowcode
allows students to design complex robotics
and control systems in a matter of minutes.
Flowcode is a powerful language that uses
macros to facilitate the control of complex
devices like 7-segment displays, motor con-
trollers, and LCD displays. The use of macros allows students to
control highly complex electronic devices without getting bogged
down in understanding the programming involved.
Part No. Description Price
01TEFLCST2 Flowcode Student Ver. $79.00
01TEFLCSI2 Flowcode Single User 182.00
01TEFLC102 Flowcode 10 Users 550.00
OPTO-ISOLATOR BOARD
This Opto-Isolator Board allows you to add 4 separate
optically isolated inputs to your E-blocks system. This is
ideal for developing industrial control systems like PLCs
(programmable Logic Controllers) where electrical sys-
tems need to be isolated from one another.
Part No. Description Price
01EB023 Internet Board $120.00
01EB032 Voice CODEC Board 210.00
01EB022 Motor Board 95.00
01EB035 Opto-Isolator Board 54.00
01EB014 Keypad Board 26.00
PERIPHERAL BOARDS
SOFTWARE AND PROGRAMMERS