Water Pressure Sensor ZETA Water Pressure Sensorr 1
Water Pressure Sensor Copyright Statement ZiFiSense owns the copyright on this specification. No part of this specification may be reproduced in any form or means, without the prior written consent of ZiFiSense. Disclaimer This specification is preliminary and is subject to change at any time without prior notice. ZiFiSense assumes no responsibility for any errors contained herein. ZiFiSense is not responsible for any patent infringement of third party on its use or as a result of its uses.
Water Pressure Sensor 目录 1. Product Description...............................................................................................................................4 2. Applications........................................................................................................................................... 4 3. Appearance............................................................................................................................................4 4. Features.............
Water Pressure Sensor 1. Product Description ZETA Water Pressure Sensor is a low power consumption module with the external water pressure detector which can report the water pressure readings periodically with adjustable alarm threshold values. The pressure sensor is installed at the inspection point by modifying the pipeline. 2. Applications Water pressure detection of booster pump, fire pump, live water pump pipeline 3. Appearance 4.
Water Pressure Sensor 5. Product parameters Product No. Wireless Features WPZTZT92 Transmission protocol Frequency band Output power Power supply Electrical Features Battery capacity Stand-by current Working current Physical Features Sensor Characteristics Working Environment Size Enclosure material Waterproof level Antenna Range Precision Operating temperature Storage temperature 6.
Water Pressure Sensor 7. Installation There are two installation methods: wall-mounted, pole-mounted. 7.1. Wall-mounted 7.1.1.Auxiliary material No. 1 2 Materials Expansion screw M6*50) Impact drill, #6 drill bit, hammer, flat-blade screwdriver, Phillips screwdriver, M6 Allen key, M6 open end wrench Quantity 4/device 7.1.2.
Water Pressure Sensor Power on Use an M6 Allen key to open the case 7
Water Pressure Sensor Install the battery and connect the sensor cable 8
Water Pressure Sensor 7.2. Pole installation 7.2.1.Auxiliary material No. 1 2 Materials Pole mounting accessories, support ≤50MM pole M6 Allen wrench, M6 open end wrench Quantity 2/device 7.2.2.Installation instructions Bracket installation Use an M6 Allen key to open the screw on the left to fix the bracket.
Water Pressure Sensor Fix the device to the pole.
Water Pressure Sensor Install the battery and connect the sensor cable 7.3. Waterproofing When installed outdoors or indoors in a humid place, the antenna port and sensor inlet of the device need to be waterproofed.
Water Pressure Sensor Three layers of protection, from the inside to the outside are: adhesive tape-clay-adhesive tape: Use waterproof tape to wrap around the interface: Cut a piece of waterproof glue, stretch it and wrap it along the RF port 12
Water Pressure Sensor Finally, use waterproof tape to wrap it again: 8. Use of Device 8.1. Steps for usage Place the device in the range covered by the ZETA network, install the battery, and wait for the device to go online. When the device is online, report the current device status once, and check whether the device is detected correctly according to the reported water pressure status. If it is not accurate, you need to check whether the range of the device and the sensor are consistent.
Water Pressure Sensor hours) Set/query reporting heartbeat cycle-m: Set or query the currently set heartbeat reporting cycle in minutes. (Range: 1-65535 minutes) Set/query the alarm cycle: When the detected water pressure exceeds the set threshold, the alarm will be reported according to the set cycle. (Range: 0-255 minutes, default value: 0, 0 means that the alarm is only reported once, without periodic reporting.
Water Pressure Sensor 9. Common faults and handling Ensure ZETA signal coverage Ensure that the device is powered on, and the ZETA network device management platform can observe that the ZETA module is on line Check the battery usage of the device. When the battery is low, replace the battery in time.
FCC Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
Water Pressure Sensor 16