ZETA AP ZETA AP 1
ZETA AP Copyright Statement ZiFiSense owns the copyright on this specification. No part of this specification may be reproduced in any form or means, without the prior written consent of ZiFiSense. Disclaimer This specification is preliminary and is subject to change at any time without prior notice. ZiFiSense assumes no responsibility for any errors contained herein. ZiFiSense is not responsible for any patent infringement of third party on its use or as a result of its uses.
ZETA AP Table of Contents Table of Contents.................................................................................................3 1. Product Description........................................................................................ 4 2. Applications.....................................................................................................4 3. Appearance & Interface................................................................................4 4. Device Specifications.......
ZETA AP 1. Product Description ZETA AP is the gateway between the ZETA wireless network and the ZETA Server. All interactions between the devices in ZETA network and the ZETA Server are done through the AP. AP communicates with the rest of ZETA network devices via the ZETA protocol, and communicates with the ZETA Server via the standard IP protocol.
ZETA AP 4. Device Specifications Model No. Protocol Frequency band Wireless Output power Number of channels Coverage Electrical Power supply Standby current Power Weight Physical Size Enclosure material Ingress level Antenna Environmental Operating temperature Storage temperature APZT-GO01/APTG-GO01 ZETA 920-925 20±3 mW 1 (expandable to 3 channels) Urban area/complex environment: 200m-2km Line-of-sight/open environment: 10-15km PoE/ AC100- 240V to DC 5V ≤100mA ≤5W 1.
ZETA AP 5. Use of AP 5.1. Antenna installation According to the device interface diagram, install the RF, GPS, and operator antennas that match the device. Note: The gateway of the test kit sends data back through the operator's network by default. Please check whether the device has a SIM card installed. If it is not installed, you need to install a suitable local SIM card by yourself.
ZETA AP 8 ： Reserved 7
ZETA AP 6. Installation 6.1. Installation Kit Before the equipment is installed, customers need to prepare the following installation tools and auxiliary materials: Name No. Use Case Screwdriver 1 For AP bracket, antenna, hoop and other screws Waterproof tape 1 For AP interface waterproof Wrench(#10) 1 Waterproof clay 1 Electrician knife 1 LAN cables (Cat.5 / Cat.5e / 1 Crystal head(TYF) 1 Cat.
ZETA AP 6.2. Gateway installation 6.2.1.
ZETA AP 4) The gateway is installed to the pole, and the other two dog teeth fixtures are passed through the screws to hug the other end of the pole. According to the actual situation of the site, the fixed direction and the position are adjusted, and the screws are fixed. 6.2.2.
ZETA AP 3) Fix the 4 clips as follows 4) Pass the hoop through the gap of the clamp and adjust the position of the gateway to the pole 11
ZETA AP 6.3. Antenna installation 6.3.1.U-ring fixing This method is suitable for scenes with a pole diameter less than 5 cm: 1) Take out the antenna U-shaped fitting and disconnect the antenna fitting screw 2) The antenna and the feeder are connected in advance and the lightning protection and waterproof measures are taken according to the specifications; 3) Close the antenna to the pole and use the U-ring in the accessory to clamp and tighten the screw as shown: 6.3.2.
ZETA AP 4) Use the spiral hoop to fix the antenna on the pole 6.4. Equipment waterproof and lightning protection 6.4.1.
ZETA AP 6.4.2.
ZETA AP 3) Finally, wrap the layer again with an electrical tape; 4) All other outdoor open-air interface of the gateway must be processed according to the above steps; 15
ZETA AP 6.4.3.Power port waterproofing 1) Pass the network cable through the connector cover, seal ring and base in turn, and press the crystal head with the wire crimping pliers, as shown below: 2) Insert the cable head into the gateway POE port and tighten the base.
ZETA AP 5) At the other end of the cable, use a crimping tool to make the crystal head and connect to the P+D port of the POE power adapter.
ZETA AP 7. Common faults and handling Check the power supply to ensure that the gateway is powered normally. Check the antenna, whether the antennas are connected correctly, and whether they are properly tightened. Check the network cable and check if the network cable is properly connected. Check the SIM card and insert it normally.
FCC Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
ZETA AP 19
