microwave radar sensor module specification (with gesture recognition) Type：KMGR-1T1R02 Version:V1.
1. Characteristic 24 GHz frequency band design. Accurate gesture recognization. Super disturbance suppression. Low power consumption, lost cost, and small size. 2. application Used in intelligent toilet with the recognization function: approximation, departure, and gesture. 3. Specification Parameter Condition Min. Typ. Supply voltage 25℃ 4 5 Current consumption 25℃,DC5V 60 67 Power consumpiton (standby) 25℃,DC5V,in standby mode Max.
Notes ①②"Antistatic ability" is only for antistatic design of products. Antistatic ability test is verified by Kemu and passed the test. ③"Walking speed range" is the theoretical value data of software design, this parameter is the research and development design of Yixing, and the validation of Kemu test is passed.
3. FCC:The design is FCC compliant. 4. Interface Num. Name Description Comment 1 VDD DC+5V Input 2 Data-Down Host -> Radar TTL 0~5V 3 NC NC NC 4 Data-Up Radar -> Host TTL 0~5V 5 GND Ground Input 5.
1) Content of communication protocol Data format： Content description： a. Data head: 4ms for high level and 8ms for low level; b. Interval code (high level): 480us; c. Data (low level): 0 - > 480us, 1 - > 1.44ms; 32 bit data in total; d.
7. PCBA structure size: Unit:：mm 14081I1310-A0-014081I1310-A0-011 8. Change record： 1. 2. V1.0 changes---initial Version V1.
OEM/Integrators Installation Manual Important Notice to OEM integrators 1. This module is limited to OEM installation ONLY. 2. This module is limited to installation in mobile or fixed applications, according to Part 2.1091(b). 3. The separate approval is required for all other operating configurations, including portable configurations with respect to Part 2.1093 and different antenna configurations 4. For FCC Part 15.
Antenna (1) The antenna must be installed such that 20 cm is maintained between the antenna and users, (2) The transmitter module may not be co-located with any other transmitter or antenna. In the event that these conditions cannot be met (for example certain laptop configurations or co-location with another transmitter), then the FCC/IC authorization is no longer considered valid and the FCC ID/IC ID cannot be used on the final product.
Federal Communication Commission Interference Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
This device is intended only for OEM integrators under the following conditions: (For module device use) 1) The antenna must be installed such that 20 cm is maintained between the antenna and users, and 2) The transmitter module may not be co-located with any other transmitter or antenna. As long as 2 conditions above are met, further transmitter test will not be required.
Industry Canada Statement This device complies with Industry Canada’s licence-exempt RSSs. Operation is subject to the following two conditions: (1) This device may not cause interference; and (2) This device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence.
Cet appareil est conçu uniquement pour les intégrateurs OEM dans les conditions suivantes: (Pour utilisation de dispositif module) 1) L'antenne doit être installée de telle sorte qu'une distance de 20 cm est respectée entre l'antenne et les utilisateurs, et 2) Le module émetteur peut ne pas être coïmplanté avec un autre émetteur ou antenne. Tant que les 2 conditions ci-dessus sont remplies, des essais supplémentaires sur l'émetteur ne seront pas nécessaires.
Manual Information to the End User The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module in the user’s manual of the end product which integrates this module. The end user manual shall include all required regulatory information/warning as show in this manual.
