Electric Vehicle AC Charger Installation Instructions
USER MANUAL TABLE OF CONTENTS 1. IMPORTANT SAFETY INSTRUCTIONS ........................................... 2 2. PRODUCT INTRODUCTIONS .............................................................. 6 3. VERIFY CONTENTS ................................................................................ 8 4. GATHER TOOLS..................................................................................... 10 5. PLAN THE MOUNTING ........................................................................ 11 6.
USER MANUAL II WARNING & CAUTION 1. Important Safety Instructions 1.1 Overall Warnings & Cautions WARNING: To avoid fire, injury or death, carefully read and follow the instructions during installation, operation and maintenance. - DO NOT put fingers into the electric vehicle connector. - DO NOT use this product if the flexible power cord or EV cable is frayed, insulation-broken, or any other signs of damage.
USER MANUAL WARNING & CAUTION 1.2 Installation Requirements WARNING: Disconnect electrical power prior to installing the charging station. WARNING: Be sure to preview the user manual and ensure local building and electrical codes are reviewed before installing the AC charger. WARNING: The AC charger should be installed by a qualified technician according to the user manual and local safety regulations. CAUTION: Use appropriate protection when connecting to the main power distribution cable.
USER MANUAL WARNING & CAUTION Consignes De Sécurité Importantes 1.1 Avertissement & Mise En Garde Généraux AVERTISSEMENT : Pour éviter les risques d’incendie, de blessure ou de mort, il faut lire et suivre soigneusement les instructions pendant l’installation, l’utilisation et l’entretien. Ne mettez pas les doigts dans le connecteur du véhicule électrique. N'utilisez pas ce produit si le cordon d'alimentation flexible ou le câble EV est effiloché, isolé ou présentant tout autre signe de dommage.
USER MANUAL WARNING & CAUTION 1.2 Exigence Avant L’installation AVERTISSEMENT : Assurez-vous de consulter le manuel d'utilisation et assurez-vous que les codes locaux du bâtiment et de l'électricité sont passés en revue avant d'installer le chargeur. AVERTISSEMENT : Débranchez l'alimentation électrique avant d'installer la station de charge. AVERTISSEMENT : Le chargeur CA doit être installé par un technicien qualifié conformément au manuel d'utilisation et aux réglementations de sécurité locales.
USER MANUAL 2. Product Introductions CAUTION: Avoid placing the charger near hot objects and at high temperature locations and away from dangerous substances such as flammable gases and corrosive materials. 2.1 Basic Interface 4.3” LCD Screen 2.
USER MANUAL 2.
USER MANUAL 3.
USER MANUAL No.
USER MANUAL 4. Gather Tools Tools required before installing the Wall-Mounted charger, gather the following tools: 1. Wire stripper 2. Adjustable Wrench 3. Voltmeter or digital multi-meter (for measuring AC voltage at the installation site) 4. Level 5. Pencil or marker 6. Drill 7. Phillips screwdriver 1 4 2 5 3 6 7 Note: The above tools are very important, please gather them all.
USER MANUAL 5. Plan The Mounting WARNING: In areas with frequent thunderstorms, add surge protection at the service panel for all circuits. Ensure all power and ground connections, especially those at the breaker and bus bar, are clean and tight. CAUTION: Not recommended to be installed in coastal environments with high humidity or high dust. STEP 1 (Only for 4G Version) Use screwdriver to loosen the 13 fixed screws on the rear of charger, then remove the front cover (for 4G Version).
USER MANUAL STEP 3 (Only for 4G Version) Tighten 13 screws on the front cover after the front cover is put back, the recommended screw torque is 1.0 N.m (9.6 lbf.in) (for 4G Version). STEP 4 Select the appropriate mounting location with electrical capacity: I. Ensure the owner has chosen a mounting location that allows the charging cable to reach the car’s charging port while still providing slack. II. The device must be anchored into mounting such as 3.14’’ x 5.11’’ stud or a solid wall. III.
USER MANUAL 6. Mount the Charging Station STEP 1 Use 4 sets Hexagonal Expansion Screws to secure the wallmounted bracket on the wall. Then level the brackets. STEP 2 STEP3 Align the rear notch of charger with the Tighten two M5 anti-theft screws to wall-mounted bracket and fit the screw complete the installation. holes of the right and left side.
USER MANUAL STEP 4 Overall outlook picture after installation.
USER MANUAL 7. Wire The Circuit WARNING: This device must be grounded. Disconnect electrical power prior to installing the charging station. WARNING: Improper connection of the equipment-grounding conductor would result in a risk of electric shock. Check with a qualified electrician or serviceman if you are not sure whether the product is properly grounded. Do not modify the plug provided with the product – if it doesn’t fit the outlet, have a proper outlet installed by a qualified electrician.
USER MANUAL 8. Operate Your Device WARNING: This device should be supervised when used around children. CAUTION: Please use the charger properly. Do not hit or press hard on the enclosure. If the case is damaged, please contact a professional technician. CAUTION: Do not put heavy objects on the charger to avoid danger. 8.1 Operating Steps with Plug and Charge STEP 1 Standby Mode: After being powered on, the lights will be all on, blue light (READY), green light (CHARGE) and red light (FAULT).
USER MANUAL STEP 2 Plug the Charging Connector: Please plug the charging connector into the vehicle charging inlet. STEP 3 Charging: The green light (CHARGE) turns to flash automatically, charging is in process. If the red light (FAULT) is on, plug the vehicle connector again. If red light is still on, please refer to "Error and Warning Messages". STEP 4 Charging finished: When the charging is finished, the green light (CHARGE) is constantly on, pull out the charging connector.
USER MANUAL 8.2 Operating Steps with RFID (Optional) CAUTION: Please keep your RFID card properly to avoid unnecessary loss. STEP 1 Standby Mode: After power-on, blue light (READY), green light (CHARGE) and red light (FAULT) all on. The blue light (READY) is constantly on when in standby mode. STEP 2 Ready to charge: Please plug the charging connector into the vehicle charging inlet.
USER MANUAL STEP 3 Swipe the RFID Card: Swipe the RFID card first and plug in the charging connector within 120 seconds, otherwise you need to swipe the RFID card again. STEP 4 Charging: The green light (CHARGE) turns to flash automatically, charging is in process. If the red light (FAULT) is on, plug in the charging connector again. If red light is still on, please refer to "Error and Warning Messages".
USER MANUAL 9. Light Codes 9.1 After Start UP Standby, waiting to plug in Waiting to charge, communicating with vehicle Charging in progress Finished charging Solid Blue Solid Green Green Blinking Solid Green Fault Solid Red 9.
USER MANUAL 10. Warranty and Maintenance • The warranty period for this charger is three years. • During the warranty period for any malfunction under normal use according to the User Manual (to be determined by certified maintenance technicians of sellers), the product shall be repaired free of charge. Except for the following situations, the charger shall be subject to the above warranty terms: 1.
USER MANUAL Thi s devi ce compl i es wi t h par t 15 of t he FCC Rul es. Oper at i on i s subj ect t o t he f ol l owi ng t wo condi t i ons: Thi s devi ce may not cause har mf ul i nt er f er ence, and t hi s devi ce must accept any i nt er f er ence r ecei ved, i ncl udi ng i nt er f er ence t hat may cause undesi r ed oper at i on.
