Electric Vehicle AC Charger Instructions
INSTALLATION INSTRUCTION INSTALLATION INSTRUCTION WARNING WARNING IMPORTANT SAFETY INSTRUCTIONS INSTRUCTIONS DE SÉCURITÉ IMPORTANTES WARNING – This manual contains important instructions for Models: AVERTISSEMENT - Ce manuel contient des instructions importantes pour les modèles: EVC10 EVC10 series that shall be followed during installation, operation and maintenance of the unit. series qui doivent être suivies pendant l’installation, l’exploitation et l’entretien de l’unité.
INSTALLATION INSTRUCTION WARNING INSTALLATION INSTRUCTION 2. Basic Interface This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
INSTALLATION INSTRUCTION INSTALLATION INSTRUCTION 3. Dimensions 4. Design Standard 3.1 Main Size of Charger 9.8″ 3.9″ Safety standards UL2594: Electric Vehicle Supply Equipment UL 2231-1: Personnel Protection Systems for Electric Vehicle (EV) Supply Circuits: General Requirements UL 2231-2: Personnel Protection Systems for Electric Vehicle (EV) Supply 14.
INSTALLATION INSTRUCTION 5. Specification INSTALLATION INSTRUCTION 6. Status Description of the Charger Indication Light Model Name EVC11 Version Rated Input Voltage 200-240 VAC Rated Output Current 16/32/40/48A Standby - Blue Light AC Power Frequency 60 Hz The READY light stays steady in standby mode.
INSTALLATION INSTRUCTION INSTALLATION INSTRUCTION Electric Vehicle AC Charger Installation Instructions Fault - Red Light The red light is lit while fault. Please refer to "8.3 Error and Warning Messages" for detailed information. 1 2 3 D FI R 7. Packing List 7.1 Safety Requirements 4 5 6 Be sure to preview the user manual and ensure local building and electrical codes are reviewed before installing the AC charger.
INSTALLATION INSTRUCTION INSTALLATION INSTRUCTION 7.2 Wiring For safe use of electricity, please add circuit breaker protection in the input part GROUNDING INSTRUCTIONS of charging pile.Connect the L1 lead to the grid L1,connect the L2 lead to the grid L2, This product must be grounded. If it should malfunction or break down, grounding provides a path of least resistance for electric current to reduce the risk of electric shock.
INSTALLATION INSTRUCTION 7.3 Tools and Materials Required INSTALLATION INSTRUCTION 7.4 Wall-Mounted Bracket Installation Tools required before installing the Wall-Mounted charger, gather the following tools: Wire stripper Crimpers for European terminals Step1 : • Set the positions of the 4 screw holes and drill them, with a diameter of 9mm and a depth of 52mm. • Use 4 sets expansion screw and M6 screw to fix the wall-mounted bracket on the wall. Phillips screwdriver for M5 Slotted screwdriver for 4~5.
INSTALLATION INSTRUCTION INSTALLATION INSTRUCTION Step3 : Fix two M5 screws to complete the installation. 7.
INSTALLATION INSTRUCTION INSTALLATION INSTRUCTION STEP3 : 8.2 Operating Steps • Hook the charger to the panel and tighten it with 2 M5 screws 8.2.1 Operating Steps With Plug The charger • Connect the power cable behind the pedestal STEP1 / Standby Mode After power-on,,blue(READY) ,green(CHARGE) and red light (FAULT) all lit. Enter standby mode and the blue light (READY) is steady on.The time from power on to the green light on is 90 seconds. READY 8.
INSTALLATION INSTRUCTION INSTALLATION INSTRUCTION STEP3 / Charging The green light (CHARGE) turns to flash automatically, charging is in process • If the red light (FAULT) is lit, plug the vehicle connector again. • If red light is still lit, please refer to "Error and Warning Messages". 8.2.2 Operating Steps With RFID STEP1 / Standby Mode After power-on,,blue(READY) ,green(CHARGE) and red light (FAULT) all lit. Enter standby mode and the blue light (READY) is steady on.
INSTALLATION INSTRUCTION INSTALLATION INSTRUCTION 8.3 Error and Warning Message STEP3 / Tap the RFID Card Tap the RFID card to start the charging. STEP4 / Charging The green light (CHARGE) turns to flash automatically, charging is in process • If the red light (FAULT) is lit, re-plug the vehicle connector again. • If red light is still lit, please refer to "Error and Warning Messages".
INSTALLATION INSTRUCTION • Avoid placing the charger near hot objects and at high temperature locations and away from dangerous substances such as flammable gases and corrosive materials. INSTALLATION INSTRUCTION 8. Malfunction and damage caused by other unavoidable external factors. Malfunction and damage caused by improper use of equipment, such as water or other solutions entering into the equipment. • Do not place external objects or heavy objects on the charger to avoid danger. 9.
