Instructions For Use Gebrauchsanweisung 6 7 HS720 usa@holystone.com (USA) eu@holystone.com (EU) jp@holystone.com (JP) ca@holystone.com (CA) +1(855) 888-6699 www.holystone.
1.0 DISCLAIMER & WARNING 1. Please read this Disclaimer & Warning and Safety Guidelines carefully before using our product. This product is not recommended for people under the age of 16. By using this product, you hereby agree to this disclaimer and signify that you have read it fully. You agree that you are responsible for your own conduct and any damaged caused while using this product, and its consequences .
④ Please do a thorough check of the product before each use. Inspect the integrity of the parts, any signs of cracks and wear of the propeller, battery power and effectiveness of the indicator, etc. If after doing a complete check any issues are found, please refrain from using the product until the issue has been resolved. 2.
2.3 Operation Requirements： ① Please don’t use this product to follow any moving vehicles . ② During the flight, only turn off the motor in case of an emergency. ③ Please flight the drone back to you as soon as possible when the battery is running low. ④ This product should not be used while drinking alcohol, if you are feeling fatigued, taking medicine, or feeling any physical discomfort. ⑤ Beware of the noise volume the drone produces. Keep your distance to avoid ear damage.
⑦ It is recommended to only use the USB charging cable that comes with the drone to charge the battery. ⑧ Don't connect the battery directly to wall outlets or car cigarette -lighter sockets. ⑨ Don't attempt to disassemble or modify the battery in any way. ⑩ Don't use the battery if it gives off an odor, generates heat, becomes discolored or deformed,or appears abnormal in any way. If the battery is in use or being charged, remove it from the device or charger immediately and discontinue use.
3.0 MAINTENANCE ① Clean the product after each use with a clean, soft cloth. ② Avoid prolonged exposure to direct sunlight and avoid buildup of heat on the drone. ③ This device is not waterproof and must not be submerged in water under any circumstance. Failure to maintain the device completely dry will result in the failure of the unit. ④ Check the charging plug and other accessories for signs of damage frequently.
4.0 PACKAGE CONTENTS ×1 Drone ×1 Transmitter ×4 Drone Battery Instructions For Use Gebrauchsanweisung Charger Hub 6 7 HS720 usa@holystone.com (USA) eu@holystone.com (EU) jp@holystone.com (JP) ca@holystone.com (CA) ×1 Screwdriver ×1 ×1 USB Charging Cable Propeller ×1 +1(855) 888-6699 www.holystone.
5.
6.0 TRANSMITTER DETAILS 6.
GPS Mode Switch When turning on the transmitter, the default mode is the GPS Mode. You can turn off GPS by sliding the switch. Check the icon “ ” or “ ”on the LCD screen to confirm whether the GPS is on or off. Return to Home (RTH) Press the button to start the RTH, the transmitter makes a beep sound and the drone will fly back to the recorded Home Point. Press the RTH button again to exit RTH procedure and regain control of the drone.
6.2 LCD Screen Functions Return to Home (RTH) Signal Strength Drone Battery Level Transmitter Battery Level Photo/ Video High/ Low Speed Mode Distance Against Home Point Amount Transmitter Altitude against GPS Mode Throttle Mode Home Point ----------------------------------------------------------- 6.3 Low Battery Warning Pic. 1 1. When the battery icon “ Pic. 2 ” is shown on the LCD screen or on the APP (Pic.
6.4 Mode Switch 6.4.1 MODE 2 (Left hand throttle MODE 2 will be default setting.) Left Joystick Up Down Descend Right Left Turn Left ----------------------------------------------------------- Right Joystick Ascend Up Forward Down Backward Left Right Turn Right Fly to Left Fly to Right ----------------------------------------------------------- 6.4.2 MODE 1 ① Hold down the “ ② Press the “ ” and then turn on the power switch.
7.0 INSTALLATION 7.1 Drone Battery Installation: Push the battery into the battery compartment at the rear of the drone. Make sure that you hear a click sound indicating the battery is firmly installed. Attention: The battery should be installed firmly, failure to do so may affect the flight safety of your drone. The drone may crash due to power-cut during the flight.
7.2 Install TF Card HEAD As shown in the above figure, place the drone bottom up, and then put the TF card (NOT included) into the TF card slot on the left side of the fuselage. ----------------------------------------------------------7.3 Transmitter Battery ② ① ③ (Not included) Step 1: Unfold the hand sticks and open the battery cover. Step 2: Install 2*AA batteries into the battery compartment according to the given polarity. Step 3: Close the battery compartment .
7.4 Propellers Installation A B HEAD B A Correct the each propeller ---The icon A/B is printed on the back of the propeller--- to its corresponding motor shaft, either position A/B, then lock it with screws by rotating clockwise. Tips: Always pay close attention to the icon A/B printed on the back of the propeller, if you want to insert any propeller to make sure they are fitted correctly, otherwise the drone will not take off.
7.5 Phone Holder 1. Pull out the mobile phone holder upwards completely (Pic. 3). Pic. 3 2. Tilt the holder 30 degrees towards you and then you will hear a click sound (Pic. 4). Pic. 4 3. Rotate and fix the support board in place (Pic. 5). Pic. 5 4. Adjust the mobile phone holder upward or downward according to the size of your mobile phone(Pic. 6). Pic.
8.0 CHARGING Charging Indicator Light ① USB Adapter (5V/0.5-2.0A) Power Bank Power Indicator Light Charging Indicator Light ② ① Connect the Battery, Charger Hub and USB Charging Cable. ② Connect the USB Charging Cable with Power Bank or a USB Adapter (5V/ 2.0A ) for charging. ③ When the battery is charging, the corresponding charging indicator of the battery is flashing green quickly, and the power indicator light is red.
9.0 OPERATION GUIDE 9.1 Download APP iOS Android APP on Google play Scan the QR code, corresponding to either App Store™ or Google™ Play Store and download the “ Ophelia GPS ” application for free. Required Operating Systems: iOS 8.0 or later / Android 4.3 or later 9.2 Connect to Wi-Fi HolyStoneFPV-****** Connect your smart phone to the Wi-Fi network created by the drone. Check the drone’s status in the ”Ophelia GPS” App.
All of the operations shown in this manual are demonstrated using MODE 2. 9.3 Pairing ① Hold the ” ” button and slide the power switch to the right to power on the transmitter, then it makes 2 beep sounds, and the indicator light “ ” keeps flashing. HEAD ② Short press the Power Switch to turn on the drone, and place it on a level surface with the head forward.
9.4 Initialization Detection HEAD 4 Place the drone on the level surface and it will enter the Initialization Detection. The red, green and yellow LED lights of the drone will alternate flickering for about 7 seconds to complete the initial detection. When completed, the transmitter will sends out “Di Di” and the front and back yellow lights will flicker. ----------------------------------------------------------- 9.
（ ） Step 2: Hold the drone vertically and rotate the drone in 3 complete circles. When completed the front Red lights and rear Yellow lights will turn solid and “ ” on the LCD screen changes from slow flash to disappear. Attention: ·If the GPS receives a signal from 7 or more satellites the indicator light on the drone will change to Red in the front and Green in the rear. ·Drone compass calibration should be done for every flight.
9.7 Unlocking 9.7.1 Unlocking the Motor Please unlock the motor before take-off. Short press the red button “ ” . The motors rotate and the drone is unlocked. ----------------------------------------------------------- Pic. 7 ----------------------------------------------------------- 9.7.2 Locking the Motor Pic. 8 Method 1: Long press the red button “ ” for 3 seconds, the motors will stop rotating immediately and the drone locks. (Pic.
9.8 One Key Takeoff/ Landing ① ② Landing Take-off ① After unlocking the drone, short press the “ ” button, the drone will automatically take off and hover at 5 feet altitude. ② When the drone is flying, short press the “ ” button, the drone will automatically land on the ground. Tips: Before flying, make sure the GPS Mode is turned on in case the drone gets lost! ----------------------------------------------------------- 10.0 FUNCTION DETAILS 10.
10.2 Return to Home (RTH) ·The Return to Home function brings the drone back to the last recorded Home Point. ·The Home Point is the location at which the drone takes off or the GPS receives a signal from 7 or more satellites for the first time during flight. The current position of the drone will be recorded as the Home Point. ----------------------------------------------------------- 10.2.
10.2.3 Low Voltage RTH ķ When the drone's rear lights flash slowly, the “ ” symbol is displayed on the screen of the transmitter, the First Low Voltage RTH will be triggered. And the drone will return automatically in the following two conditions: (At this time, the drone can only fly within a safe range of the height no more than 98 feet and the distance no more than 328 feet .) H98 feet a.
② When the drone's rear lights flash quickly, the “ ” symbol is displayed on the screen of the transmitter, and the transmitter sounds “Di..., Di...”. At this moment, the Second Low Voltage RTH will be triggered. H50 feet a. When the filght altitude is higher than or equal to 50 feet, the drone will stay in the current altitude and return above the Home Point then desend vertically. H50 feet 50 feet Home Point Flight Altitude 50 feet b.
10.3 Image Positioning System ķ The Image Positioning System consists of a camera ķ module, which acquires the position information of the drone through visual images to ensure precise positioning and safe flight of the drone. ----------------------------------------------------------- The Image Positionin System is typically used in indoor environment when GPS is weak or unavailable. It works best when the drone altitude is less than 5 meters.
available, your drone will switch to Gesture Mode automatically. Be cautious to operate the drone in the following situation: 1. Fly fast at an altitude below 0.5m. 2. Fly over monochrome surfaces (like pure black, pure red, pure red and pure green). 3. Fly over strong light reflective surfaces or surfaces prone to reflection. 4. Fly over water or transparent object surfaces. 5. Fly over moving object surfaces (such as crowds, swaying juggles and glass). 6.
11.0 APP OPERATION INSTRUCTION 11.
11.2 Setting Parameters Click the “ ” icon to enter the setting interface (as shown in the figure above), you can set a limited flight range: 1. Maximum flight altitude: 50~390 feet/ 15~120 m. (The default flight altitude is 390 feet.) 2. Maximum flight distance: 160~1600 feet/ 50~500 m. (The default flight distance is 3200 feet.) 3. Maximum flight radius: 16~320 feet/ 5~100 m. (The Point of Interest's flight radius is set at 16 feet by default.
11.3 Follow Me When the Follow Me function is enabled, the drone will follow the GPS in your smart phone to follow you wherever you go. 1. Ensure the drone's flight range is within 15~95 feet. 2. Click the“ ” icon on the app interface, and click “ YES ” in the prompt box to enter the Follow Me function — the drone will now follow the phone’s coordinates. 3. To exit Follow Me Mode, simply click the“ ” icon on the app interface again.
11.4 TapFly It is recommended to enlarge the map if you want to use TapFly. 1. Click the“ ” icon on the app interface, and click “ YES ” in the prompt box to enter the TapFly function. MODE 1: Click the“ ” icon on the app interface, draw a line on the screen to create a path, click“ ” icon to submit the route, then click" YES ", and the drone will fly along the path. MODE 2: Click the“ ” icon on the app interface, set any point on the screen, click“ ” icon to submit the route, then click" YES ".
11.5 Point of Interest 3 1. Click the“ ” icon on the app interface, and click “ YES ” in the prompt box to enter the Point of Interest function. 2. The drone will record it’s flight position the moment you enter this function as the point of interest. The drone will now continuously circle clockwise around the preset point. (The default radius is 16 feet. To change the point, please click “Setting” —“Flight Radius” to reset.) 3.
11.6 Take Photo/ Video 1. Click the “ ” icon to switch between photo and video mode. 2. When the shutter button is “ ”, click once to take a photo. 3. When the shutter button is “ ”, click once to start recording, and click again to stop recording. 4. Click the “ ” icon to enter the photo album for viewing. Pic 9 When the TF card is not installed, the photos or videos will be stored directly in the APP photo album (Pic.9) and smartphone.
12.0 DRONE STATUS INDICATOR IndicatorStatus Status Indicator Meanings Front and rear lights alternate flashing The drone is not connected to the yellow. transmitter. Red, green and yellow lights flashing and alternate. Drone is currently in Initialization Detection status. F R Front light turns solid red, rear light turns solid yellow. No GPS signal or weak GPS signal. F R Front light turns solid red, rear light turns solid green. Good GPS signal. Front and rear lights flash green quickly.
13.0 SPECIFICATIONS DRONE Model: HS720 Weight: 460g / 16.2oz Flight Time: 26 minutes Operating Temperature Range: 32° to 104°F Dimensions: 173 x 104 x 56 mm (Folded) 336 x 370 x 56 mm (Unfolded) DRONE BATTERY Capacity: 2800 mAh Voltage: 7.4 V Battery Type: Li-Po Energy: 20.72 Wh Charging power: 15.2 W Charging Temperature Range: 41° to 104°F (5° to 40°C) Charging Time: 5~7 hours TRANSMITTER Operating Frequency: 2.4 GHz MAX Transmission Distance: 2624~3277 feet (outdoor and unobstructed) Battery: 2×1.
CAMERA Camera frequency: 5 GHz Video/ Photo Resolution: 2K (2048×1152p) Lens: FOV 110° FPV Distance: 656~1312 feet (outdoor and unobstructed) Photo: JPEG Video: AVI / MP4 MAX Supported TF Cards: 32 GB (Not included) Controllable Range: Pitch: -90° to 0° Operating Temperature Range: 32° to 104°F USB CHARGING CABLE Voltage: 5 V
14.0 TROUBLE SHOOTING No. Problem Solution When the drone is powered on, the indicator light keeps flashing rapidly. The drone is in the gyroscope calibration state. Please place the drone on an flat and level surface. 2 The drone cannot hover after takeoff and tilts to one side. Place the drone on a flat, level surface and repeat the gyro calibration. 3 The drone vibrated in flight. The propeller are damaged. Please replace the new propeller.
16.0 GENERAL INFORMATION FCC Statement: Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.
WARNING: Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. RF Exposure The equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This device should be installed and operated with minimum distance 20cm between the radiator & your body. This part belongs to the drone. RF warning for Portable device: The device has been evaluated to meet general RF exposure requirment.
2) I'utillsateur de I'appareil doit accepterbrouillage radioélectrique subi meme si le brouillage est susceptible d'encompromettre le fonctionnement. mauvais fonctionnement de I'appareil. Cet appareil numériquie de la classe B est conforme à la norme NMB-003 du Canada. CAN NMB-3 (B) RF Exposure Radiation Exposure Statement: This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment.
BATTERY WARNING: 1. Failure to follow all the instructions may result in serious injury, irreparable damage to the battery and may cause a fire, smoke or explosion. 2. Always check the battery’s condition before charging or using it. 3. Replace the battery if it has been dropped, or in case of odor, overheating, discolouration, deformation or leakage. 4. Never use anything other than the approval LiPo charger the battery. Always use a balancing charger for LiPo cells or a LiPo cell balancer.
11. Non-rechargeable batteries are not to be recharged. Rechargeable batteries are only to be charged under adult supervision. 12. Different types of batteries or new and used batteries are not to be mixed. 13. Batteries are to be inserted with the correct polarity. 14. The supply terminals are not to be short-circuited. Regular examination of transformer or battery charger for any damage to their cord, plug, enclosure and other parts and they must not be used until the damage has been repaired. 15.
The Statement of compliance is available at the following address: http://www.holystone.com/Download/CE/HS720_EU_DOC.pdf This product can be used across EU member states. MANUFACTURER INFORMATION Manufactured by Xiamen Huoshiquan Import & Export CO., LTD Room 703,No. 813-2 Xiahe Road, Siming District, XIAMEN, China +1(855) 888-6699 FAA REGISTRATION: PLEASE FOLLOW ALL FEDERAL, STATE AND LOCAL FAA LAWS.
